Join Now
International Automotive Technicians Network
Prev Professional Automotive Repair Technical Discussions for January 29, 2015
International Automotive Technicians' Network (iATN) - Members Only
Next
(Also Available: All, Asian, Chrysler, European, Ford, GM.)
Vehicle Owners: If you are seeking an automotive repair professional to service your vehicle, visit the iATN Repair Shop Finder.

Open Help Requests for Chrysler
Help Request Answers
2007 Chrysler Pacifica Limited 4.0L Transfer case VIN: 2A8GF78XX7
This was sold off our used car lot . Customer drove car for about 2 months and Transfer case Grenaded ( Came apart inside , blowing out the case ) The case that was in the vehicle at that time looked like a Brand New unit. So I am assuming it was just replaced...
View
1991 Dodge Dakota 3.9L abs VIN: 1B7GG26X6M
replaced all steel brake lines .rear e-brake cables and rear cylinders.bled system and now have abs light plus red brake light on.pedal stops about 3 inchs from floor and does not pump up or fade under pressure.it almost feels like rears are not working .adjus...
View
2001 Dodge Dakota Sport 4.7L No Start VIN: 1B7HG2ANX1
When truck gets up to operating temp. It will have long crank after a soak. Some times cold frist thing in morning. If you cut key off and back on fires right up. Have new fuel pump. But pressure still falls off as fast as you cut off key. Still starts right b...
View
2004 Dodge Ram 2500 SLT 5.9L No Start, hard start VIN: 3D7KU26C64
had trouble getting truck to start when it is cold. Intake heater is working good and engine is cranking over good 200-225 rpm and lift pump pressure is 15 psi while engine is cranking. hooked up computer and had no codes and checked data and found high pressu...
View
2006 Dodge Grand Caravan SXT 3.8L Hesitation VIN: 2D4GP44L66
Good morning all! I have a demon here! The first time customer made complaint of delayed shifting and noise while in gear. They stated that it didn't want to pull itself. They said they were told it was the transmission. The vehicle was dropped off and we look...
View
2007 Dodge Caliber SXT 1.8L No crank VIN: 1B3HB48C07
hi everyone got a 07 Dodge Caliber with a no crank condition if you feed 12 volts to the starter it runs normally, through our diagnostics we discovered that on a scan tool the WCM data pid reads "Valid key" in the on position but reads NO during crank positio...
View
2011 Dodge Nitro Heat 3.7L Vent System VIN: 1D4PU5GK5B
We removed the left vent & found wires pinched in duct work We removed Dash & Checked for blockage or unhooked duct work & found the duct work was not restricted or un-hooked but it was not sealed good to heater box. We checked all doors and motors while the d...
View
2003 Jeep Liberty Sport 3.7L no heat VIN: 1J4GL48K03
sitting still it has great heat but wen you start driving the vehicle it gets cold when the heat is all the why up
View

Fixes & Summaries for Chrysler
Fix/Summary Answers
2008 Dodge Grand Caravan SE 3.3L Pedal hieght VIN: 2D8HN44H88
Thanks to all who offered help we fixed the van by replacing the rear calipers, I would also like to say to [...] from Virginia we may not all be as smart as you but I can reference factory manuals that employ pinching off brake lines to diagnose problems. Now...
29
2010 Dodge Grand Caravan SXT 3.8L MIL Lamp on VIN: 2D4RN5D12A
Vehicle is fixed I did scope cam and crank. It was apperant the cam signal was out of range. Jasper wanted the unit replaced befour they picked it up I pulled the timing cover. There was a chunk of casting on the timing cover interfering with the signal. Than... Trouble codes: P0344.
10
Prev (Also Available: All, Asian, Chrysler, European, Ford, GM.) Next