× Auto Repair Pros Member Benefits TechHelp Knowledge Base Forums Resources My iATN Marketplace Chat Pricing About Us Join Industry Sponsors Video Members Only Repair Shops Auto Pro Careers Auto Pro Reviews
Join Now
International Automotive Technicians Network
Prev Professional Automotive Repair Technical Discussions for January 28, 2015
International Automotive Technicians' Network (iATN) - Members Only
(Also Available: All, Asian, Chrysler, European, Ford, GM.)
Vehicle Owners: If you are seeking an automotive repair professional to service your vehicle, visit the iATN Repair Shop Finder.

Open Help Requests for Chrysler
Help Request Answers
2001 Chrysler PT Cruiser Limited 2.4L timing belt VIN: 3C4FY4BB91
I am in the process of replacing this timing belt...whoa ! This has VERY little room to do it . Do you have ANY tips or suggestions on how to make this job easier ?
2006 Chrysler 300 C SRT8 6.1L Fuel Trim VIN: 2C3LA73W46
I have posted about this car previously. I have a found somthing of interest to what the computer is doing with the injector and coil control. I have confrimed that this engine is lean. During the symptom occurance when STFT are peaked postive 33%, I can add p...
2007 Chrysler PT Cruiser 2.4L No Start VIN: 3C3JY45X57
I would like to start by thanking everyone who takes a minute to take a look at this post. I just finished putting a new head gasket on this car, had a compression leak from cyl. #4 to cyl. #3. Car ran OK when it came in, just had a p0304 misfire code. Car cra... Trouble codes: P0108 (Map voltage incorrect), P0122 (Tps voltage incorrect)
1998 Jeep Cherokee Classic 4.0L Dome Lights Etc VIN: 1J4FJ68S7W
Possible short in rear door jam harness? with both connectors that feed the dome lights and connect near the a pillars under the sill plates.
2008 Jeep Liberty Limited 3.7L Blower VIN: 1J8GN58K58
I have a customer with 2008 Jeep liberty 3.7L engine with manual HVAC system. The blower motor will quit working from time to time but will usually come back to life if the ignition switch is turned off and back on. Today he brought it in not working so I chec...

Fixes & Summaries for Chrysler
Fix/Summary Answers
1995 Chrysler Town & Country 3.8L 2-3 shift VIN: 1C4GH54L2S
Well the input sensor did the trick. Shifts great now. I didn't even consider using the scan tool on it. I must be getting old. Thanks again to all who relied.
2001 Dodge Ram 2500 5.9L camshaft expantion plug VIN: 3B7KF23631
Thank you for all the very helpful replies. We replaced the expansion plug with an other factory plug and o ring. This time we used anaerobic sealer and peened the center of the plug a little more than we did before. So far so good, its been gone for 2 weeks ...
2011 Dodge Grand Caravan Crew 3.6L No Start VIN: 2D4RN5DG6B
Van is fixed. I monitored the voltage on the fuel pump fuse in the TIPM while powering up the fuel pump with the scanner and could see intermittent drop outs of the voltage at the fuse. I found a kit referred to in a forum for the Durangos and it fit this appl...
2006 Jeep Commander Limited 4.7L Oil Pressure Light VIN: 1J8HG58N66
Looks like I may have over-reacted here. The initial problem was a bad sensor, but after replacing the sensor I got a light stuck on at the 2nd key cycle. Seems to have been just an air bubble. Long story short - bad sensor - replaced - saw light - paranoid - ... Trouble codes: P0522.
2011 Ram 3500 Laramie 6.7L Wireless Ignition Node VIN: 3D73Y3CL6B
Hello, sorry for the late response to close this. the key came out fine with some firm wiggling. no problems with the key. I was worried about breaking the key, but I took a chance. installed a new WIN, programmed it with Wytech and all is well
Prev (Also Available: All, Asian, Chrysler, European, Ford, GM.) Next