 Prev |
Professional Automotive Repair Technical Discussions for May 27, 2014 International Automotive Technicians' Network (iATN) - Members Only |
Next  |
| (Also Available: All, Asian, Chrysler, European, Ford, GM.) | ||
| Vehicle Owners: If you are seeking an automotive repair professional to service your vehicle, visit the iATN Repair Shop Finder. | ||
Open Help Requests for Chrysler
| Help Request | Answers | |
| 1998 Chrysler Sebring JX 2.5L Starting VIN: 3C3EL45H1W Keeps blowing fuse 8 for starter under hood power distribution center NEVER after it gets towed in though started 40 times no problems does have aftermarket security system checked all wiring looks good Thanks for all/any help |
View | |
| 1998 Dodge Ram 1500 ST 5.2L No Start, Stall VIN: 3B7HF13Y6W Customer brought me in this Ram and said is just wouldn't stay running. Truck will start and run for about 3 seconds and then just stall out. I have checked fuel pressure (47psi), 5 volt reference (4.89volts), removed exhaust from manifolds to make sure cat.... |
View | |
| 2001 Dodge Ram 3500 5.9L Surge VIN: 1B7MF33651 have tested for codes lift pump pressure scaned with snap on scaner boost presure. suspect either lock up pulse or possible inj pump problem problem only happens in od at 45-55 mph at steady speed give a little more throtle or let off throtle and it stops. no ... |
View | |
| 2007 Dodge Sprinter 2500 3.0L Hesitation VIN: WD0PE74517 We believe we need to replace the swirl valve actuator replaced. Alldata is misleading in telling us what to remove to replace the actuator. One area says to remove intake manifold and another area says to remove transmission to gain access. What is the correc... Trouble codes: 2513 (Swirl Actuator Motor) |
View | |
| 2007 Dodge Ram 3500 ST 6.7L No Start VIN: 3D7MX38A87 Customer states truck died on road, will not crank. Had multiple communication codes stored, but nothing returns once cleared. Theft light is not on. Data looks normal in all modules. The key I'm hoping someone has seen before is the PRND display does not ligh... |
View |
Fixes & Summaries for Chrysler
| Fix/Summary | Answers | |
| 2002 Chrysler Voyager 2.4L Fuel system VIN: 1C8GYN2712 Thank you for the help. I did not fix the vehicle. Customer took it to other place, and they are trying to remove failed injector, but some other people glued the injector in place, since it was leaking diesel, and now it is very stuck in place. I did not purs... |
2 | |
| 2001 Dodge Intrepid SE 2.7L instrument cluster VIN: 2B3HD46R61 thank you to all for your thoughts . as of yet the customer has not decided to fix the car , she is starting the car every other day . the relay system with an ignition feed sounds like the least expensive route . i will need to find out what else will be cont... |
8 | |
| 2007 Dodge Caliber SXT 2.0L Poor Idle Quality, Hesitation, Surge, Cuts out, Misfire, MIL Lamp on VIN: 1B3HB48B77 we found several corroded wires in the wiring harness in the left fenderwell we replaced a few real bad ones and repaired several bad wires we also replaced the etc or throttle body it is commonly called and finally after all this we got the vehicle running sm... Trouble codes: P0700, P0161, U0170, U0171. |
7 | |
| 2007 Dodge Charger R/T 5.7L turn signals VIN: 2B3KK53H37 tried function test with scanner,still no rf or lr,found 30 amp maxi fuse blown in integrated power module,still unable to run the function test.replaced front control module,everything works fine |
7 | |
| 1989 Jeep Wrangler 2.5L Poor Idle Quality, Stall VIN: 2J4FY19E8K I check for vacuum at the EGR valve. It was not present when the idle problem was. I ran a Motorvac fuel cleaning on the fuel system to begin with and, after cycling the vacuum at the EGR valve with my vacuum pump, coupledwith the fuel cleaning, the idle was s... |
5 | |
| 1942 Willys Americar 2.2L Clutch VIN: 0MB5805980 John [...] got it right but many others who replied were on the right track. I pulled the trans out and found no problem visually with disc, pressure plate or throw out bearing. No leaks from the rear main or the input shaft seal. The grease on the input ... |
29 |
