 Prev |
Professional Automotive Repair Technical Discussions for July 7, 2010 International Automotive Technicians' Network (iATN) - Members Only |
Next  |
| (Also Available: All, Asian, Chrysler, European, Ford, GM.) | ||
| Vehicle Owners: If you are seeking an automotive repair professional to service your vehicle, visit the iATN Repair Shop Finder. | ||
Open Help Requests for Chrysler
| Help Request | Answers | |
| 1994 Chrysler LeBaron Landau 3.0L transaxle VIN: IC3EU4530R I have this Lebaron that goes into limp in on start up. There are no codes, checkin at the blue 6 pin connector under the dash. On my Modis it says it is in limp in, and it is, immediately after start up but the tcm is still commanding the shifts 1st thru 4th.... |
View | |
| 2001 Chrysler LHS 3.5L No Start VIN: 2C3HC56G71 I have a 2001 Chrysler LHS 3.5 Liter engine. Had the computer reprogramed at the dealer. I can put the key in to start nothing happens. Dash lights come on no starter response. |
View | |
| 2005 Chrysler PT Cruiser Classic 2.4L Hesitation, Surge, Cuts out, MIL Lamp on VIN: 3C4FY58B25 Help Please! I got this 05 PT Cruiser in the shop cant seem to fix it. The car came in with P0344 and the customer had replaced the Cam sensor. I have the OE sensor and have tried a third new Borg Warner and they all do the same thing. It runs fine when cold b... Trouble codes: P0344 (Cam position sensor circuit intermittent) |
View | |
| 2006 Chrysler PT Cruiser 2.4L Clutch release system car came into shop with clutch inop when hot. No pedal pressure at all. Once cooled down, pressure is Back to normal. Replace clutch master and slave assembly with oem parts, bled system, all seemed okay . Clutch feels like normal. Gave car back to customer, a... |
View | |
| 2008 Chrysler Sebring 2.4L MIL Lamp on VIN: 1C3LC46K58 This car cam in with MIL on and the two listed bank 1 camshaft 2 code listed. This car is only 2k out of warranty. I have not seen this problem on a chry. Have you Chry guys seen this? Mitchell talkes of a camshaft phaser. But there is no info on it. Thank Y... Trouble codes: P000B, P0014 (bank1 cam 2 postion target preformance) |
View | |
| 1998 Dodge Grand Caravan 3.8L Odometer VIN: 1B4GT44L6W The BCM was replaced with a used unit and now the odometer reads the milage from the other vehicle. I need to reprogram the BCM so that the odometer reads the correct milage. Can I correct the odometer reading using a DRB III? If not how can the odometer be co... |
View | |
| 2003 Dodge Ram 2500 5.9L Steering VIN: 3D7KU28C53 please send help on this one. customer brought to my shop sais t walks around on interstate. i had replaced entire front end prior 3 months ago.. ball joints both sides torqued to specs. all tie rod ends and steering shock. roadtest and verify. when it goes ri... |
View | |
| 2003 Dodge Neon SXT 2.0L unknown VIN: 1B3ES56C63 This car presented with a customer complaint of occasionally 'flying out of gear'. As I understood the scenario the car would be running down the highway and the engine would rev up and quit pulling. We scanned the car found codes PO732 Input RPM does not matc... |
View | |
| 2004 Jeep Liberty Sport 3.7L Cooling Fan VIN: 1J4GL48K34 Fans power up with a/c but not under normal conditions should come on at 203f did not come on at all up to 224f scanner will power up fan when commanded. No codes relays have been swaped no diffrence / relays all seem good |
View |
Fixes & Summaries for Chrysler
| Fix/Summary | Answers | |
| 1997 Chrysler Town & Country LX 3.8L starting VIN: 1C4GP64L7V The problem was a cluster cicuit board bleeding voltage on the CCD buss causing the start and shut down.Replace circuit board and all is fixed. Thanks Guys for all your inputs. |
3 | |
| 1994 Dodge Caravan 3.3L Excessive Emissions VIN: 1B4GH44R7R Thanks to all who posted replies so quickly. I tested catalytic converters and found the results to be borderline, tested O2 sensor and also found them to be borderline. So i replaced o2 sensors and the vehicle passed |
12 | |
| 2003 Dodge Durango SLT 4.7L Tps Dtcp0124 VIN: 1D4HS38NX3 eventual testing led us to find TCM getting bogus feedback from b1s1 o2 before cat. replaced o2 and and cleared P0700, p0124, & p0613. Mitchell diagrams never showed o2 sensors to be wired through TCM on any diagram. ground in 02 which is black & blue wire a... |
4 |
