 Prev |
Professional Automotive Repair Technical Discussions for April 1, 2010 International Automotive Technicians' Network (iATN) - Members Only |
Next  |
| (Also Available: All, Asian, Chrysler, European, Ford, GM.) | ||
| Vehicle Owners: If you are seeking an automotive repair professional to service your vehicle, visit the iATN Repair Shop Finder. | ||
Open Help Requests for Chrysler
| Help Request | Answers | |
| 2005 Chrysler PT Cruiser GT 2.4L No Start VIN: 3C8FY78G25 Hi guys. This one has me baffled. Customer scheduled an appointment earlier in the week for sputtering complaint and a check engine light on. It got towed in as a no start. Has good fuel pressure and 130 pounds of compression - followed diagnostic tree to repl... Trouble codes: P0171 |
View | |
| 1988 Dodge Caravan SE 3.0L Stall VIN: 1B7GK1332J After driving this van for over 15 o 20 minutes it dies at stops or under long periods of deceleration. The problem is not always present. Sometimes when reaching a stop ligth, after 10 or 15 second of engine idling the engine starts to run rough and then dies... |
View | |
| 2005 Dodge Sprinter 3500 2.7L limp mode Vehicle came in today with customer complaint stating vehicle goes into limp mode after driving longer distances. Customer called yesterday, stating it was in limp mode,we told him to reset ignition(waited 15 minutes). He drove vehicle home and it ran great. N... |
View | |
| 2001 Jeep Grand Cherokee Laredo 4.7L power seat worm drive The passenger seat worm drive gear is stripped. Which only allows the seat to move half an inch, then stops. There are 2 drives. One for right track, and one for the left. I pulled out the worm drive assembly and confirmed that it is locking up inside the worm... |
View | |
| 2002 Jeep Grand Cherokee Laredo 4.0L No Start, Stall, MIL Lamp on VIN: 1J4GW48SX2 Well techs got another one for you. No start on this one. New cam sensor and gear installed in same way it came out. New crank sensor installed. Coil asm installed. Still no start. Well when first came in it had codes P0122 TPS,P1495 LDP, P0340 No cam signal. ... Trouble codes: P0122 (TPS Voltage Low), P1495 (Leak Dection circuit open/short), P0340 (Nocam signal), P0320 (No crank reference signal at PCM) |
View | |
| 2005 Jeep Liberty Limited 3.7L limp mode VIN: 1J4GL48K75 we rebuilt transmission 4000 miles ago for this problem. customer states jeep went into limp mode pulled codes po841 l-r pressure and po846 2-4 pressure . tested found nothing wrong. cheched cvi were within specs and no pressure loss. checked for reflashes non... |
View | |
| 2006 Jeep Grand Cherokee SRT8 6.1L Unknown VIN: JDH3452345 Hi there this is my first help request. I HAVE A 06 srt8 cherokee came in with a loud cirping/squalking type niose. sounded like water pump impeler hitting inside of housing. so i removed drive belt noise still there. noise only there at idle. off idle it gose... |
View |
Fixes & Summaries for Chrysler
| Fix/Summary | Answers | |
| 2000 Chrysler Concorde LX 2.7L no shifting on this car i had 2 problems which i had to get a drb3 to see. first was a sol pack that was bad and would not show on the modis and ethos. the other issue was the trans module itself was reading -3 degrees F causing the trans to operate in extreme cold mode 2... |
12 | |
| 2007 Chrysler Town & Country LX 3.3L coil pack cracking VIN: 1A4GJ45R47 Replaced ECM. First ECM replacement was defective.No further information avaliable. |
10 | |
| 2001 Dodge Caravan SE 3.3L Poor Fuel Economy, PORR COLD START VIN: 1B4GP253X2 Replaced pre-cat o2 sensor and road tested. Problem was solved after vehicle drove about 20 miles. Customer states fuel economy and starting issues are resolved to her satisfaction. Thanks for all the help on this one. |
4 | |
| 2002 Dodge Neon SE 2.0L Poor Idle Quality, Surge, Misfire VIN: 1C3ES46C32 thanks for all the help guys, turns out that the engine back fireing seperated the intake, replaced it runs fine know |
18 | |
| 2006 Jeep Liberty Limited 2.8L abs lamp VIN: 1J8GL58546 Hello all Thanks for all the info., you guys hit it right on, when i performed the initilization i had car in bay key on engine off, this put vin# in module however never completed initilization. I had to take starmoble on test drive and perform initilizatio... |
5 |
