Prev iATN Members TechHelp for April 10, 2008
Automotive Technical Exchange for the Automotive Repair Professional		 Next
(Also Available: All, Asian, Chrysler, European, Ford, GM.)
Vehicle Owners: If you are seeking an automotive repair professional to service your vehicle, visit the iATN Repair Shop Finder.

Open Help Requests for All Makes and Models
Help Request Answers
2001 Audi TT 1.8L ABS module
ABS module needs coding, tried typical Audi brake system codes; 00022, 00021, 06169, 00031, 00004, 00204 and 00106, does anybody have the correct code? please, help Alex		 View
1993 BMW 325i 2.5L blower motor
still only high speed, rechecked voltages, no power out of resistor, put on another and it works, i got resistor from world pac behr brand name. this is just a warning that there may be some bad resistors being sent out		 View
1994 Buick Skylark 2.3L Excessive Emissions, Poor Fuel Economy
when customer purchased vehicle it would not pass e-check . he returned to the dealer and they kept the vehicle for a week. dealer had vehicle tested and it passed. they would not tell the customer what they had to do to get it to pass. now this year vehicle w... Trouble codes: OX-13 (oxygen sensor circuit failure).		 View
1989 Cadillac Fleetwood 4.5L Starting
Hi techs: we have this 89 fleetwood that was towed in with a no start complaint. we checked for fuel and spark and have fuel but no spark. checked for 12 volts to dist. and was ok next we checked ign. coil, cap, rotor and ign. module all checked ok. checked gr...		 View
1990 Cadillac DeVille 4.5L Driver Info Center, A/C Control Panel
I hate Cadillacs!! This car came in for a bad fuel mileage problem. I dropped the under dash hush panel to access the ECM to current ramp the injectors. The car has "neon" lights under the dash but the controller plugs into the cigarette lighter with NO splici...		 View
1984 Chevrolet Corvette 5.7L transmission
I have an 84 corvette with the doug nash 4+3 transmission. It clunks from 1st to 2nd gear, and when the engine is cold and idling at about 1500rpm the gears will not slip in from 3rd to 2nd; The car has to be stopped and put back into 1st. Eklers sales a rebui...		 View
1985 Chevrolet El Camino 5.0L Hesitation
I am seeking advice from hot rodders. It's been a long time since I tinkered with one of these! I recently installed this engine in my brother's car. It runs great and will smoke the tires off of it once I get past the stumble and hesitation in it. I set the i...		 View
1993 Chevrolet Pickup 5.7L rotors
This problem existed before the brakes were done the truck drives excellent until brakes are applied it then pulls to the left and then right all the time and worsens the harder the brakes are applied		 View
1995 Chevrolet Caprice 5.7L Misfire, MISS FIRES IN DRIVE
Hi everyone.I have a good one for you all.I installed a motor into this impala ss.The motor is from a 95 camaro.It starts fine but runs with hearing a little pop out of the exhaust once in a while.I checked the firing order and that is fine.When I step one the...		 View
1997 Chevrolet Blazer 4.3L fuel guage
GM tech wanted! i need a part number for the fuel level buffer module or call it the slosh module or call it whatever you want, I'm staring at it and nobody at the dealership will try and look it up because they have never heard of it before. After we explaine...		 View
1998 Chevrolet Lumina 3.1L MIL Lamp on
car came in with mil on po401 code. i checked snap on troubleshooter and says that pcm does a test once every ign cycle.and at 40mph on decel pcm opens egr and checks for map volts to raise.i took a movie and checked map sensor voltage when pcm is testing and ... Trouble codes: PO401 (insuffiecent egr flow).		 View
2000 Chevrolet Monte Carlo 3.4L wipers
Wipers stop in the up position when in the delay mode, they will park in the down position where they are suppose to be but does a funky jerk before it moves to park		 View
1999 Chrysler Concorde 3.2L evaporator
Hey All., Sorry about this super technical post. Were is the third through bolt for the evap case? Aldata says there are three and I can only find two. I've spent and hour looking for this thing and I fiqure someone here can bail me out. I believe I have all t...		 View
2003 Chrysler PT Cruiser 2.4L Fan Circuit
Used car with inop ac. Evac and recharge system. No leaks verified. Bleed off valve started releasing r-134 while finishing recharge of system. Verified fan stopped spinning and was not coming on with a/c. Only opperating with engine temp. My beleif was either...		 View
2004 Chrysler Pacifica 3.5L Auto Stick
This vehicle came in with the autostick staying in low gear when car is cold. In the morning when you get in and place trans in drive the prndl display shows all autostick digits lit up and the car will not shift out of low. After a little while trans works fi...		 View
2005 Chrysler Town & Country 3.8L cv joints inner
hi, thanks for your time. One of my clients has had 2 axle shafts break in the last 1,000 miles, both times this has occured when making a hard turn (park lot) I can find no damage and the cradle looks to be in the proper place, I saw the tsb regarding the pow...		 View
1997 Dodge Stratus 2.5L Poor Idle Quality, Hesitation, Misfire, MIL Lamp on
Engine runs rough at idle and hesitates on acceleration. I tried to motorvac the vehicle but no help. Fuel pressure is good. Volume is good. Checked for vacuum leaks with smoke machine. No leaks found. I'm thinking I have partially plugged injectors. I don't r... Trouble codes: P0300 (Randommultiple misfire detected.), P0171 (System too lean bank 1).		 View
2001 Dodge Caravan 3.3L MIL Lamp on
Have a stubborn evap code here and I seem to be overlooking something. Have reveiwed posts and checked vacum lines by airbox area and have replaced LDP and bad gas cap due to locking part of cap not working. Still have a 456? Have smoke tested the sytem for le... Trouble codes: P0456 (evap system small leak detected).		 View
2002 Dodge Pickup 4.7L Surge, Cuts out, Stall
this dodge idles great in park and in gear. let the rear wheels turn it dies. rear wheels off the ground, truck idling in nutural spin rear tires by hand the truck dies. i can give it some gas and drop it in gear on jack stands and it will run but it runs very... Trouble codes: p0601 (pcm internal self test fail).		 View
2003 Dodge Grand Caravan 3.3L abs sensor
Hi, Guys I have this van that come in with a ABS light on and code for right rear speed sensor signal malfunction. Test drove and found that the right rear speed signal on the scanner is 0mph but sometimes it will just jump to a crazy amount like 78mph while t...		 View
2003 Dodge Dakota 4.7L check gauge light on
truck came in for full service and has CHECK GAUGES light on, all gauges read normal, cust stated that the alt gauge seems to be a little bit higher than before. charging test show 13.3 at idle with a analog gauge you can see the needle fluctuate a bit when th...		 View
2005 Dodge Grand Caravan 3.3L Soft pedal
Came in for poor brake pedal and the rear shoes were wore out and the front pads were thin. We replaced the pads and shoes and both rear wheel cylinders because they were seeping. The pedal didn't get very good so we changed the master cylinder. It got ok but ...		 View
1985 Fiat X1/9 1.5L Valve adjustment
Does anyone have a valve shim removal/installation tool for one of these gathering dust that they would like to part with? I'm willing to pay a fair price. Alternatively does anyone know where I can get one? I've already tried Difatta Bros., International A...		 View
1991 Ford Ranger 2.3L No Start, Misfire, MIL Lamp on
This Ranger has the 8 plug 2 coil pack system. It came in as a no start. I checked fuel pressure and it is ok. I scanned and KOEO is a Pass 11 KOER could not be done at this point. I next checked firing order and found #1 and #2 crossed on the intake coil pack... Trouble codes: 98 (failsafe mode).		 View
1992 Ford Ranger 2.3L Timing Belt
Hi This costumer complains of lack of power due to the timing belt jumped a couple of theeth. It ocurred him sometime ago two times and the solution they find was simply buy a generic belt and install it. This time I want to buy the original part and check a...		 View
1999 Ford Pickup 7.3L high pressure oil pump
I recently replaced the high pressure oil pump.The customer has brought vehicle back with an oil leak.It appears to be coming from the front of the engine valley, it appears to be where the oil pump meets the gear cover.Everything was spotless prior to assembl...		 View
1999 Ford Expedition 5.4L losing coolant into oil
I have NO history on this vehicle, but if you try to fill the cooling system I get a severe leak into the oil. all the water runs into the oil. My GUESS is a leaking head gasket but I would like some words from some experinced Ford 4.6 techs giving me some ins...		 View
2000 Ford Focus 2.0L Battery lamp
I could really use some help on this one. I have a problem with the charging system on this focus. It came in with the battery light on complaint and flickering lights. When we checked the charging system with midtronics tester, it condemned the alternator, no...		 View
2000 Ford Pickup 7.3L No Start
This truck was towed in for no start, scanned for codes and no codes where present, so as a comon problem fix replaced cam sensor and no change, even tried another in hopes of a defect, still no start, it will turn over good just won't start, hooked scanner up...		 View
2003 Ford F450 Super Duty 6.0L oil pressure
truck was towed in. would not start. diagnosis led to base oil pressure problem. removed oil pan, checked and cleaned pick-up screen. install pan-new oil and (oem)filter. pressure still below 5 psi. remove oil pressure regulator, cleaned and reinstalled. no ch...		 View
2003 Ford Pickup 5.4L Starting
I have a 03 F-150 that came in on the hook with a NO CRANK per customer. When first tried starting, the engine cranked over but would not start. Had the Flashing security light and the odometer was just dashes, no numbers. pushed vehicle in and found codes u12...		 View
2006 Ford Explorer 4.0L MIL Lamp on
Customer complaint: Could not fill fuel tank, pump would click and shut off, like the tank was already full. Had 2 codes: PO451 (Evap Pressure Sensor Circuit) and P1450 (Unable to Vent/Bleed Fuel Tank Press/Vac) R&Red Fuel Tank, replaced Vent Solenoid/valve (... Trouble codes: p1450 (Unable To Vent Fuel Tank Vacuum).		 View
2006 Ford E450 Super Duty 6.8L Poor Idle Quality
Vehicle came in with customer complaint of poor idle quality and intermittend idle stall. Retrieved codes found P0505 Idle air control system fault. cleared codes and retested, code had not come back but vehicle continues to have idle surge and intermittent st... Trouble codes: P0505 (Idle Air Control System Fault).		 View
1997 GMC Pickup 6.5L push rod
Had a noise on start up and when warmed up engine was missing.With scanner found #2 cylinder was the one not helping.also had a popping noise in intake. pulled valve cover and found exhaust push rod bent but not out of place.Valve seems to open fine now. My qu...		 View
1999 GMC Pickup 5.7L No Start
This truck will start and stall instantly. seems like security issue. No communication with scan tool to PCM or any other modules. All fuses are good. SES light will come on with key on but no other lights on dash e.g. (air bag, seat belt, message center, door...		 View
2004 GMC Sierra 6.6L runs out of fuel
this truck fuel gage reads empty and both tanks are full.now when the front tank runs low it wont transfer from rear and will run out of fuel, and i jumpted the leveling or transfer pump and it works? how does this sys. work have no wiring diagram.do the tanks...		 View
1993 Honda Accord 2.2L Stall
This Car has something completly strange. Everything is perfect when car is in the shop. NO CODES NO SYMTOMS FUEL PRESSURE OK NO VACUUM LEAKS iGNITION SYSTEM OK Transmission shifting O.K The problem starts, only when the car is in complete motion. Every single...		 View
2008 Honda Accord 3.0L Day Time Running Lights
The Car Uses The High Beam Bulb As The Day Time Running Light. It Does This By Supplying The Bulb With 2.5-3.0 Volts. This Illuminates The Same High Beam Buld Only Bimmer. Something Like A Dimmer Switch Used At Home Using A Regular Incondesent Light Bulb. ...		 View
2001 Hyundai Elantra 2.0L No Start
car starts ok in the morning and when cold, after engine warms-up and try to restart the engine it will take a very long time to start. if a disconect one of the sensors (i.e. cts or ats) engine starts right up. i've replaced coolant temp sensor, map sensor, c...		 View
1989 Isuzu Trooper 2.6L No Start
This was towed in as no start. ECU was out but plugged in , another ECU laying in seat beside it. Has been to several other shops including dealer & I get it now. It has no spark & check engine light doesn't come with key on.All-Data not much help with this. W...		 View
1992 Jeep Wrangler 4.0L Excessive Emissions
orignally came in failed smog for being way to rich, found the tps reading 4.6 volts all the time running in clear flood, replaced tps know failing nox, at 15 mph hc7, co0, co2 14.7% nox 1400, at 25 mph hc 3, co0, co2 15.0%, nox 200, tested o2 again switching ...		 View
2003 Jeep G. Cherokee 2.7L solenoid
Hello This WG 2003 Grand Cherokee is europen diesel version (2.7 CRD). Engine and transmission from Mercedes. TCM will go to limp home mode sometimes with code "Power supply to solenoid". ECM will set code P0700. There is a TSB (21-009-08) regarding a very ...		 View
1993 Lexus LS 400 4.0L No Start
Car came in with a no start. Checked for codes, non were found. First sprayed carb cleaner into intake, and acted like it wanted to start, so I went for fuel pressure. No pressure. Went to trunk and checked for power at fuel pump and has none. After looking at...		 View
1999 Lexus RX 300 3.0L Parking brake light and chime
Customer stated, "Once in a while the chime for the parking brake warning will chime, daughter saw a light on the dash flash but didn't know which one. I checked the fluid resivior(topped it off) and parking brake pedal. Nothing obvious. Customer called today ...		 View
1998 Lincoln Mark VIII 4.6L Ride Control
Hello, We have this Lincoln here that after it sits for a day the front driverside sinks down to the ground. Here is what we have doneso far, Replace Both front control solinoids and retainers, scaned for codes and performed auto test and comes up with codes 1...		 View
1990 Mercedes-Benz 300SE 3.0L Cruise control
Hi everybody, got this 1990 300 SE with cruise control operating at times and when it does it is not smooth or consistent as it may engage suddenly or disconnect at will. When selecting 'acc' it will engage with a jerk and when in 'set' will not engage at all ...		 View
2003 Mercedes-Benz CL55 5.5L pwr window / seat
this is Paris hilton's ex car, it's a pink cl55 AMG. whether that's related to the problem or not I don't know.., but here's the problem I'm having: the car is in for inop right front power window and seat adjustments on that same side. basically nothing on t...		 View
2003 MINI Cooper 1.6L transmission
We replaced the transmission in the mini cooper. We are getting ready to fill the transmission or gearbow up with fluid. According to the information on alldata the fill plug is on the front of the transmission close to the block. We don't have the recommended...		 View
1992 Mitsubishi Diamante 3.0L Shifter
Wrecker driver dumped this jewel in the middle of the yard and left while I was out. (It will not run...ECU burnt but this is not the problem problem.) AUTOMATIC GEAR SHIFTER will not unlock. How do I unlock this beast ? KOEO Brake ON, still locked. Don't s...		 View
1993 Mitsubishi Montero 3.0L No Start
vehical crank fine no start. i have spark at the plugs. i do not have fuel injector pulse. i have power to the fuel injectors. i have no gound signal from pcm. reading discription of opration in alldata. the pcm uses both crank and cam sesnor in dist. for spar...		 View
2002 Nissan Altima 2.5L engine
Vehicle is consuming coolant over time. No external leaks found. Has now started to run a little rough on start up then clears up quickly. Convinced we have a headgasket type issue, and that the head needs to be removed. Just wondering if any "characteristic" ...		 View
2004 Nissan Sentra 1.8L No Start
I will try and be to the point. This car has been at four shops including dealer for a NO start. The car was a cranking No start at Midas and was told needed a tune. They broke a plug and bailed out. Second shop pulled head did head gasket and timing chain. It...		 View
2006 Nissan Pathfinder 4.0L Poor Idle Quality
hey guys got a 06 nissan pathfinder in the shop. we did and induction service on the vehicle and then learned about how the throttle body worked. if any body knows off hand of the relearn procedure it would be greatly appreciated. thank you,		 View
1992 Oldsmobile Achieva 2.3L Coolant Reservoir
Hi all, This vehicle came to me with a complaint of oil in the coolant reservoir. Engine runs perfect. No misfires or smoke. Customer stated he changes the oil every 3000 miles and has not noticed the car using or burning any oil. Car does not overheat and I h...		 View
2002 Pontiac Grand Prix 3.8L starter
Vehicle towed in as a no start. Put vehicle up with helper turning key, No power on Purple selenoid wire on starter, voltage on Bat+ wire. Crossed selenoid, engine cranked. Talked to local dealer Tech, Said Ignition Switch bad. Sounded good. Replaced ignition ...		 View
2005 Pontiac GTO 6.0L starting
Got a real fun job on my hands, Customer purchased a complete 2005 Pontiac GTO engine with controller and transmission to install into his 1993 truck. I am concerned that the engine after installed won't start because of theft deterrent. I have looked at the G...		 View
1983 Porsche 928 4.5L speedometer
This is for the 928 porsche man. The speedometer is inoperative. In the past if the vehicle is driven over a big bump on the freeway the speedometer will work for some time. (bad connection somewhere) But now it's totaly dead, The speedometer have been sent ou...		 View
1988 Porsche 924 2.5L oil warning sys
Help all Porsche Techs!! We have this 924s that will intermittenty flash the oil pressure warning light on while the engine speed is above idle. The bar gauge reads normall pressure. We cannot duplicate the concern but want to correct this for the customer. An...		 View
2001 Porsche 911 3.4L Mechanical
car was towed in, customer was driving car to work. car starts but runs poorly. check codes. found code for left camshaft position sensor. implausible signal. check sensor. sensor appears ok. checked engine compression. zero compression on left bank. right ban...		 View
1999 Saab 9-5 2.3L Excessive Emissions, Poor Idle Quality, Stall
Here is my saab story. we got vehicle with engine siezed. we removed engine as sublet to local rebuilder. engine rebuilt and installed by us. Engine runs great when driving, at idle it struggles to keep running and sets two codes p0300, and p1251. we cleared p... Trouble codes: P0300 (random engine misfire), P1251 (throttle out of range).		 View

Fixes & Summaries for All Makes and Models
Fix/Summary Answers
2002 Audi Allroad 2.7L air struts
replaced both struts and compressor. also did new adaptation and system worked ok 		4
2000 BMW 740iL 4.4L Transmission, ABS, Insterment cluster
Well, after checking everything i could, we bit the bullet and tried a new ABS module. ($1700!) Coded it, and it seemed to work! No commutation problems, no can bus codes! The customer picked the car up and we haven't heard back, i'm assuming everything work...		 8
1992 Buick Riviera 3.8L Charging
thanks for all the help, the problem was in the inst cluster, low voltage light never came on with key on. customer didnt want to spend more money to have inst pannel rebuild. rebuilder we use for alternator added a self energing regulator. thanks again every...		 15
1993 Cadillac DeVille 4.9L Excessive Emissions, Misfire
This was a real time eater but with your help we got it to pass emissions here in arizona. Ray [...] helped when he said the the o2 sensor will keep it from going into closed loop ans Juan [...] reminded me about the cracking computer boards and poor ground ...		 21
1988 Chevrolet Van 5.7L head lamps
GOOD JOB GUYS. FOUND THE BULK HEAD CONNECTOR NEXT TO BRAKE MASTER CYLINDER COVERED IN UNDERCOATING FROM 20 YEARS AGO!!! AFTER DIGGING CONNECTOR OUT OF COATING AND SEPERATING, FOUND WATER AND A BROKEN WIRE. REPAIR WIRE, RESEALED, AND RECHECKED OPERATION, PER...		 23
1993 Chevrolet Pickup 4.3L no speedometer
thanks to larry@donsauto. I had already checked power supply at calibrator and all was good, checked again with a load at that circuit and lost voltage, I replaced ignition switch, now voltage is good, trans shifts, speedo works. thanks again		 7
1995 Chevrolet Van 5.7L Hydro Boost
Thanks everyone for the help with this problem. So in fact it was the pump. After everyone's feedback about how the pump could be the most possible cause, i went ahead and borrowed a friends gauge that he had made purposely for such a system. 44 PSI was see...		 15
1996 Chevrolet Suburban 5.7L blower motor
Well we checked the drain and checked for water leaks inside the vehicle and found nothing-owner did not want to pursue any furthur repairs such as the sealing of the hvac and cowling as some suggested.Says he will worry about it if he still has the truck come...		 12
1997 Chevrolet Blazer 4.3L Misfire
first of all thanks for all the replies,after some thought,this was a pretty simple problem,based on the exhaust readings. with only 6 hc's on a major misfire i realized this was a fuel injection problem. using scan tool found ltft @ +25 on bank 1. i removed ... Trouble codes: PO300 (multiple misfire).		 16
1998 Chevrolet Cavalier 2.2L MIL Lamp on
I tried disconnecting the battery overnight. No change. checked for vacuum leaks with smoke machine, none found. Could not get new throttle body. Customer did not want to put any more money into car. Thank you to all that replied. Trouble codes: P0507 (IAC Speed high).		 5
1999 Chevrolet Tahoe 5.7L radio light
The best response was from Alvin, it was 13 volts and .60 watts. There are a few sources for these bulbs, Alvin has his source and Suburban Electronics is another. Pretty straight forward to replace, remove faceplate from radio, solder in all new bulbs. 		3
2000 Chevrolet Venture 3.4L sliding door
bad latch assy kept releasing and disenging contacts.		 5
2002 Chevrolet Venture 3.4L Hesitation, Misfire
thanks to everybody with your thoughts on this one.90% of you suggested doing a motovac.we did this twice and greatly improved the performance.the van did come back 5 days later with a code for just #2 cylinder misfire.we replaced #2 injector and all is good.c...		 22
2003 Chevrolet Malibu 3.1L Poor Idle Quality
Iwant to thank all of you for taking your time to help me out,especially David,Lamar and Scott, you guys are right on time,A iac cannot bring engine rpm up to 4000 rpm,so i'm will refer customer to the dealer,recall nhtsa [...] for accelerator pedal binding... Trouble codes: P1122 (TP sensor circuit intermittent low voltage), P1554 (Cruise control feedback circuit).		 7
2003 Chevrolet Suburban 5.3L A/C tentioner
WOW iatn members do it again I had 20 replies and almost every one responded with sludging up of the compressor. as this compressor was only 6 months old I was concerned about what else I would find but I must have been lucky. I replaced the compressor again w...		 20
2000 Chrysler Town & Country 3.8L tcm
Found that the wiring harness under the battery chafed to the frame and shorted the b+ feed to the fused 12 volt start signal to the tcm . it caused the tcm to shut down and go in to protect mood. thank you all for your help.		 8
2001 Chrysler Town & Country 3.8L master cylinder
The customer has not yet return from Florida. Sorry Friends but feel I let my customer down.When he returns I will replace the abs hcu. I beleeve from some of the replies I got thats,going to fix the problem.		 33
2005 Chrysler Sebring 2.4L Front Crank Seal
I did find the crankshaft with alot of end play. Thanks to all that replied. This system is great. Chuck's Automotive		 15
1998 Dodge Caravan 3.3L emmision rejection
ta all thank you, we put pcm in flashed it go the monitors to run and passed emmissions.		 2
2002 Dodge Durango 4.7L MIL Lamp on
I was waiting to post, until I heard what the dealer told the customer, but customer has not gotten back to me - replies agreed that the Chrysler website and the dealer did not have the proper information - perhaps the current flash was the latest and the PCM ... Trouble codes: P0456.		 4
2002 Dodge Grand Caravan 3.8L turn signals, w/s wipers
I have not been able to experience the symptom myself yet. There were 3 grounds for the BCM. I disassembled and cleaned the one at the starter, for the two that are in the B pillars I ran an auxilary ground to them. I also disconnected the battery and touched ...		 6
1967 Ford MUSTANG 302CID turn signals
thanks again to all who helped out. i changed the turn cam which had the two wires to make contact, the metal wires were to long so i cut them just a bit so they would make contact inside. i guess live and learn when buying some parts. thank you all for help a...		 8
1990 Ford Bronco II 2.9L flexplate spacer
local salvage yards didnot have spacer. for giggles and grins i decided to call rusty eck ford in wichita, they had the part on their shelf. lucky me thank for answers anyway		 1
2000 Ford Pickup 5.4L dash
Thanks for replies. I had to replace the cluster and reprogram. to fix this one.Some one had install a used cluster.Wiring was all good 		3
2000 Ford Expedition 5.4L heater
just as a few other users requested i check all of the vaccum hoses and everything checks out ok, i switched the a/c control head w/ a known good one and still nothing. Talked to other technician that did blend door and actuator and he stated he had some trou...		 4
2000 Ford Focus 2.0L starter
I have not figured this one out yet. I made the post and the next morning the customer showed up and said they had to have the car to make a trip out of town. Additional info I got was the car has 3 different drivers, and none of them can agree on what exactl...		 6
2000 Ford ZX2 2.0L No Start
First of all thank you all, this site kicks a**. Im calling this one fixed its been gone for a while now and the customer called and said all is well. I guess the constant control module fixed it.. THanks again		 14
2002 GMC Safari 4.3L MIL Lamp on
We have replaced the distributor gear, cam sensor, timing chain ,front cover , ignition wires, pcm, and nothing has helped. cylinder heads have been removed and guides and springs have been rechecked and all are good with no sign of scoring. we are removing th... Trouble codes: P0300 (random missfire), P0335 (testing and results).		 4
2006 Honda Accord 2.4L airbags
Sorry for the long delay, but I have not worked on the vehicle since. The customer is rounding up other parts for the vehicle. The replies were pretty well anonymous that the module needs to be replaced. Most never heard of resetting the module. Thank you. 		12
2003 Jaguar XK8 4.2L No Start
Hello everyone, Sorry it took so long to close thise one I went on vacation and forgot it was open. It was the fuel pump. At the fuel rail pressure was 5 psi. At the fuel filter pressure was 5 psi. At the tank out let it was 5 psi. R&R tank, bench tested ...		 5
2003 Jeep Grand Cherokee 4.0L MIL Lamp on
THANKS TO ALL WHO TOOK THEIR VALUABLE TIM [...] TO HELP ME WITH THIS PROBLEM AFTER I WENT TO ALL THE SUGGESTIONS DROP GAS TANK.SMOKE ALL THE HOSES AND NOTHING HELPED KEITH.GUY AND MICHAEL HIT IT RIGHT IN THE NOSE I USED THE VACUUM PUMP TO TEST THE LDP VENT VALVE AN... Trouble codes: P-0455 (evap lrge leak found).		 8
2005 Jeep Wrangler 4.0L Hesitation, Stall
we changed the crank sensor and customer is happy with the results. thanks everyone for your help.		 4
1991 Mazda MPV 3.0L No Start
Pcm pulse width was the complaint, replaced with rebuilt Pcm. Thank you all so much.		 10
1993 Mazda MX-6 2.0L No Start, Poor Idle Quality, Surge, Stall
Thanks guys for all of your help. I received a lot of good information. Everything that i received was checked out or double checked, still have problem. Customer doesn't won't to continue. 		3
1987 Mercedes-Benz 560SEL 5.6L No Start, Starts/Dies quickly
The reason the fuel pump was replaced was due to a very bad leak around the end seal of the pump housing. The car came in running fine. The only reason the battery was disconnected was because this particular vehicle's fuel pump is external and has a positiv...		 10
2002 Mercedes-Benz C240 2.6L center vent blow hot air
OK This one is at last out of the shop.After replacing all stepper motors & broken operating levers (flap linkages) and the same code keep coming back. So we decided to replace the A/C & Heating control panel. It doesn't need to be coded, even MB interchanged ...		 3
2002 Mercury Sable 3.0L No Start, Stall
You ever feel like you chase your own tail!Thanks to all the replies.But to Ed from PENNSYLVANIA thank you Tech lost his butt,he had overlooked a broken brown and white which is vref.broke in half bigger than Dallas.This time we pulled the fender skirt.You got...		 6
1978 MG MGB 1.8L turn signals
thank you all I found that the ground at the licence plate frame was poor and also the ground at the right tail light was dirty and loose was a very easy fix thanks to all of you giving me the ground locations information like this is priceless thanks all...		 9
2001 Mitsubishi Montero 3.5L Misfire, MIL Lamp on
Thanks fellow techs that offered help unfortionatly I was not unable to figure out what was going on with this vehicle one interesting thing was when the engine started to misfire the O2 sensors would flat line it was like the computer was shuting down fuel co... Trouble codes: P0300 (Random Misfire).		 4
1996 Nissan Maxima 3.0L monitor not ready
The customer has driven over 900 miles and finally show up for checking the monitor readiness and it did completed the monitors and also able to pass the smog test. Thanks for some of you mention regarding that it took so long to complete the monitor. Also app...		 16
Prev (Also Available: All, Asian, Chrysler, European, Ford, GM.) Next