Join Now
International Automotive Technicians Network
Prev Professional Automotive Repair Technical Discussions for October 4, 2007
International Automotive Technicians' Network (iATN) - Members Only
Next
(Also Available: All, Asian, Chrysler, European, Ford, GM.)
Vehicle Owners: If you are seeking an automotive repair professional to service your vehicle, visit the iATN Repair Shop Finder.

Open Help Requests for Chrysler
Help Request Answers
2000 Chrysler Sebring LXi 2.5L won't accelerate VIN: 4C3AU52N9Y
Hello fellow techs...this one's driving me nuts...what am I missing?? Car sounds like plugged exhaust or timing real retarded, will start and idle but does not want to accelerate, (slow acceleration). I have checked all the basics, even timing belt. Customer c...
View
1996 Dodge Stratus ES 2.5L Temp Gauge VIN: 1B3EJ46X0T
Temperature gauge runs in the blue.Replaced sensor and gauge still only goes up only one needle width.Removed thermostat to inspect and found that one of the legs was broken. We installed new thermostat and gasket and still have the same results , temp gauge d...
View
1993 Jeep Wrangler 4.0L Stall VIN: 1J4FY29S6P
i have a strange one the injector pluse is stuck at 64.56 the desired idle reads 8975 the pluse reading never changes under no throttle or full throttle fuel pressure is 38 psi all other pids ok o2 sensor switches ok anyone else see this befor also the vehcal ...
View

Fixes & Summaries for Chrysler
Fix/Summary Answers
1999 Chrysler Town & Country (Van) LXi 3.8L Poor Fuel Economy, loss of power VIN: 1C4GT64L5X
Well, this none is done and down the road. I had a lot of good ideas from everybody such as fuel pump, MAP sensor, flexplate and ignition. It turned out to be too much exhaust backpressure. Michael from Ohio was right about the back pressure but was thrown,... Trouble codes: P0300.
10
2003 Chrysler Town & Country (Van) LXi 3.8L Electronic VIN: 2C4GP54L13
This vehicle is a very clean vehicle. I tested all circiut with while aplying a load again and all passed. I removed all connections, opened the harness and inspected splices and wires again and found no abvious failures. I inspected the power distribution ...
6
1994 Dodge Caravan 3.0L shift shaft VIN: 2B4GH2530R
Thank you PROs for your helps. It's a really great idea that I can access to the inside shift links through the oil pan without uninstalling the TM. However, I replaced the oil pump gasket and the big seal, and I fixed the leak problem. Furthermore, I found th...
4
2003 Dodge Ram 2500 Truck 5.9L TSB # 24-004-03 (Blend door inoperative) VIN: 3D7KU28603
I would like to first thank all those who replied to my posting & especially to Chad in Minneapolis. Where without Chad's pertinent information, the blend door most truly break again (from what I hear any where from a few months to a few years). ...
6
2004 Dodge Intrepid SE 2.7L pump VIN: 2C3HH46R24
Installing a new power steering pump from Chrysler has solved my noise problem. I let the customer try it for a while and contacted him today and no more power steering noise. The new pump came with a resevoir. The first pump I installed was a NAPA rebuild an...
6
1985 Jeep Grand Wagoneer 5.9L Cuts out, Stall VIN: 1JCNJ15N2F
Finally, I moved the auxillary solenoid off the fender down onto the frame to facilitate easier suction of fuel by the electric fuel pump. The customer is happy, and I am relieved to get rid of the old beast. It was a learning experience. If I can only remembe...
14
1995 Jeep Grand Cherokee Orvis 4.0L door locks radio,center command center VIN: 1G56YHI865
thanks to the whole 5 people that tryed to help, agian thanks.it was the under hood fuse and some corrosion at a few connectors.jeep has had better lighting and seams to run better customer says so great fix, agian thanks everyone who tryed to reply.
5
1999 Jeep Grand Cherokee Limited 4.7L No Start VIN: 1J4GW68N9X
Thanks everybody who responded, problem turn out to be a cam sensor. Next time will replace both crank and cam sensor.
8
Prev (Also Available: All, Asian, Chrysler, European, Ford, GM.) Next