Join Now
International Automotive Technicians Network
Prev Professional Automotive Repair Technical Discussions for May 5, 2007
International Automotive Technicians' Network (iATN) - Members Only
Next
(Also Available: All, Asian, Chrysler, European, Ford, GM.)
Vehicle Owners: If you are seeking an automotive repair professional to service your vehicle, visit the iATN Repair Shop Finder.

Open Help Requests for Asian
Help Request Answers
1996 Honda Accord EX 2.7L MIL Lamp on VIN: IHGCE6679T
This honda came in with MIL on for P0401 and P0725 the ignition coil took care of the 725 code but i replace egr valve and it came back on right after she left the shop. So to CYA i put a vacume solenoid on and cleaned the egr tube.Should have done that before... Trouble codes: P0401 (EGR insufficient flow), P0725 (engine speed sensor circut malfunction)
View
2003 Honda Civic Hybrid 1.3L no idle stop VIN: JHMES966X3
This vehicle will most times not idle stop,maybe once or twice a day will it work. Sometimes at a light it will idle stop after sitting like it should in stop and go traffic. I have tried with the climate control off or in economy and doesn't make any differen...
View
1999 Isuzu Rodeo LS 3.2L abs VIN: 4S2CM58W9X
This vehicle came in a few days ago with an ABS light. Customer stated that while driving down his driveway the pedal went to the floor and he actually ran into his bushes. After this the ABS light was on and stayed on. I drove the car and the brakes worked gr...
View
1990 Mazda Miata 1.6L No Start VIN: JM1NA3517L
This car came in yesterday for rear brakes and dies when cold start. I assumed idle speed problem. Recommended Motor Vac and clean isc. Hooked to motorvac and ran 30 minutes with out running engine. Cleaned injectors witn engine running for another 30 minutes....
View
1999 Mazda B2600 2600CC Poor Idle Quality, Hesitation, Surge VIN: MNA8SFD70X
This may be one for you Aussies out there as this vehicle may be exclusive to our market. I need some help on diagnosing the 3 pin air flow meter. The owner was advised by a roadside assistance organisation that the air flow meter is faulty, but due to the cos...
View
1996 Nissan Pickup 2.4L timing chain VIN: 1N6SD11S4T
ok, i was ask if i might look at this one , it was stalling at times. checked the basic stuff without verifying the problem, well after driving for a few days it had act up,it had a dtc for maf sensor,replaced the throttle body top(that is way to expensive!) a...
View
1998 Toyota RAV4 2.0L Excessive Emissions, Surge VIN: JT3HP10VSW
This Toyota problem is eluding me. It has a surge at acceleration and cruise. Customer is getting about 10 mpg. No codes. The fuel trims are showing a rich condition. LT Trim B1-S1 -2.3 Total Trim .95 Also has pid of Trim B1-S1 (%) -100. The plugs are black. H...
View

Fixes & Summaries for Asian
Fix/Summary Answers
1994 Acura Vigor GS 2.5L SRS,horn VIN: JH4CC2663R
The clockspring was shorted internaly. We installed a new one as suggested and problems were solved.
15
1984 Nissan 300ZX 3.0L Poor Idle Quality, Hesitation, Cuts out, Stall VIN: JNIHZ14S2E
Hello Everyone, Thanks to the three who responded. James from Florida recommended a new cylinder head temp sensor & pigtail which are evidently still available thru Nissan. John [...] from 'The Z Shop' in north carolina and James from Montana both stated that a... Trouble codes: 13 (Coolant Temp System), 21 (Ignition System), 22 (Fuel Pump System).
3
1996 Nissan Maxima GLE 3.0L Starting VIN: JN1CA21D4T
hey, just wanna say thanx to the guys that responded, found a bad ignition switch, i apologize for the lack of info, but you guys are great
11
1999 Nissan Maxima GLE 3.0L Hesitation, Surge VIN: JN1CA21A5X
To all members of iATN thank you for your help ,to this date I have been unable to repair this vehicle. I replace all the sparke plugs and the coils the problem still presisit.As soon as I find the problem I will let every one know . Trouble codes: P1320 (ignition system misfire malfuction control), P0325.
15
2000 Toyota Camry CE 2.2L ballance shaft VIN: 4TGB22K7YU
Hi All I want to thank all who responded. Some said thicker shims, Some said thinner shims. And some said replace the balance shaft. Well a few of you said You dont need it. Howard [...] was the first to say I did not need it and he told me why and how. Wh...
15
Prev (Also Available: All, Asian, Chrysler, European, Ford, GM.) Next