 Prev |
Professional Automotive Repair Technical Discussions for October 7, 2016 International Automotive Technicians' Network (iATN) - Members Only |
Next  |
| (Also Available: All, Asian, Chrysler, European, Ford, GM.) | ||
| Vehicle Owners: If you are seeking an automotive repair professional to service your vehicle, visit the iATN Repair Shop Finder. | ||
Open Help Requests for European
| Help Request | Answers | |
| 2006 Audi A4 Quattro 3.2L Esp VIN: WAUDG74FX6 Vehicle came in with ESP light on and ESP Fault-Visit Workshop message. Scanned with VAGCOM/VCDS and found code 00493-004 in Brake Control Module (Module 04). Performed Steering Angle Sensor calibration (listed possible cause for code, info from Ross-Tech), co... |
View | |
| 2008 Audi Q7 Premium 3.6L MIL Lamp on VIN: WAUZZZ4L38 after picking up car at dealer after inlet manifolds replaced,the eng went into limp mode,glow plug light was flashing,eng check light on,found code for hpfp fault,dealer says metal in pump,can someone steer me to some work instructions to replace pump thanks.... Trouble codes: 00013 |
View | |
| 2004 BMW 525i 2.5L ABS module VIN: WBANA53574 Vehicle came in with a 5E34-Left rear wheel speed sensor error code and a 5E30- Left wheel speed sensor no voltage and no speed signal from l/r wheel. I checked for power and ground at the left wheel sensor and had a ground but no power on the blue/white wire... |
View | |
| 1983 Porsche 911 SC 3.0L oil VIN: WP0EA0919D After driving vehicle for more than 10 miles, oil will blow back into air box. We have checked oil level with car hot hot and at idle, does this car have a pcv system that might be clogged?? any help is appreciated john |
View | |
| 2012 Volkswagen CC Sport 2.0L Stall VIN: WVWNP7AN2C to Vw gurus out there. got this CC that had melted the fuel pump control unit. vehicle was towed in from the dealer who recommended a replaced fuel pump and fuel pump control unit. replaced them and the vehicle ran for about two minutes and then it stalled. if... |
View |
Fixes & Summaries for European
| Fix/Summary | Answers | |
| 1996 Audi A4 Quattro 2.8L abs VIN: WAUEA88D0T Removed sensor and cleaned, blew out sensor ring and set sensor clearance. Sensor had pushed out when replacing axle and had rust on it. Really appreciate all the replies, very helpful. Thank you! |
9 | |
| 2008 Mercedes-Benz CL550 5.5L Lr Window Motor VIN: WDDEJ71X48 Replaced module and that solved the problem Thank you to everyone who responded. |
4 | |
| 2010 Mercedes-Benz GL350 Bluetec 4Matic 3.0L Ride height VIN: 4JGBF2FE4A Great thanks to Tony in California he was spot on this one just like he said were the air spring rolls over in the lower position. Terry from cal. and Richard from Florida,Lars,Chuck and Greg were all in agreement. Thank You Duane |
6 | |
| 2001 Porsche Boxster Roadster S 3.2L Check engine light VIN: WP0CB29841 The P0343 code refers to the cam sensor signal wire short to battery voltage. I did confirm both sensor had 12V on the signal wire but these are 5V hall effect sensors and it's on the signal wire not the reference wire. I did scope both sensors, they had a goo... |
7 | |
| 2008 Saab 9-7x Aero 6.0L Starting VIN: 5S3ET13H78 This one is fixed!! I can't stress enough to not over think things. I did confirm a slow switching pattern from my B1 o2 sensor. After a long conversation with the customer i found out he replaced the o2 sensor without clearing the code. These use a resistor t... |
7 |
