Join Now
International Automotive Technicians Network
Prev Professional Automotive Repair Technical Discussions for May 7, 2015
International Automotive Technicians' Network (iATN) - Members Only
Next
(Also Available: All, Asian, Chrysler, European, Ford, GM.)
Vehicle Owners: If you are seeking an automotive repair professional to service your vehicle, visit the iATN Repair Shop Finder.

Open Help Requests for Chrysler
Help Request Answers
2003 Chrysler 300M 3.5L transmission VIN: 2C3HE66G73
Got this 03 Concorde that came to a trans shop with a Output Speed Sensor code and harsh shifting. Trans shop replaced output speed sensor and valve body. Now it's setting a code P0845 2/4 Hydraulic pressure test failure code. Odd thing is when you look this c...
View
2007 Chrysler PT Cruiser Limited 2.4L starter VIN: 3A4FY58B57
Hey guys,never seen this before,its probably a common problem.Customer states by moving shifter around they could make car start,my thinking was range switch rite off the bat,upon the car being checked out we noticed if you keep pressure inward on the key it w...
View
2008 Chrysler Town & Country Touring 3.8L master cylinder VIN: 2A8HR54P58
Is there a special procedure to do rear brakes? Pads were frozen in mounts, After cleaning and lubing everthing pads were replaced pistons screwed back into calipers ok. Now the brake pedal slowly sinks almost to floor before stopping sinks wether running or n...
View
2005 Dodge Grand Caravan SE 3.3L solenoid block VIN: 1D4GP24R65
another shop replaced solenoid block back in september & again in december (I believe for same concern) . came here & had codes in TCM for all solenoids in block & p0700 in pcm (expected with tcm codes). tested solenoid circuits , all ok. had PCM replaced by d...
View
2007 Dodge Charger R/T 5.7L Not start after running or hot VIN: 2B3KK53H77
Car has been in two times for no start after hot. first time found remote start installed. no issues until this was done. refered back to installer. cust has system removed. Issue is still present . Also hard slow crank start when it does start like a weak bat...
View
2008 Dodge Ram 2500 SLT 6.7L tempeture VIN: 3D7KS28A58
What would cause the high side pressure to come down to 80 or 90 when going down the road at speed and it works good at slower speeds and sitting in the shop?
View
2003 Jeep Grand Cherokee Laredo 4.7L compressor clutch VIN: 1J4GW48N73
veh. has had 4 compressors installed by other shops along with every piece to ac system from evaporator to condenser and all hoses but still burns up compressor clutch after 2 to 3 days of replacing compressor not sure where to go from here anyone had issues l...
View
2005 Jeep Grand Cherokee Limited 4.7L left axle VIN: 1J4HR58N65
This 200F differential is trying to win. I had to replace the steering gear which required dropping the front differential assembly. I needed to replace the axle seals anyway. All was going fine until I got to the left axle. I can't get that thing to pop out o...
View
2006 Jeep Commander Limited 5.7L cooling fan VIN: 1J8HG58296
Hello guys. Need Chrysler techs advice on this Jeep. Having problem with hydraulic fan that is not being commanded on based on A/C or ECT until I use my scanner to actuate it. It spins at idle around 100-500 rpm with 0% Fan PWM. With A/C on (or with high e...
View

Fixes & Summaries for Chrysler
Fix/Summary Answers
2006 Chrysler 300 Touring 3.5L Parking Lights VIN: 2C3KA53G96
thanks to all that replied the problem was in the ipcm power control module. as i said i was able to turn the park lights on and off with a breakout relay and all my control pids were responding normaly. we have another of these vehicles with another ipdm prob...
6
2008 Dodge Ram 1500 SXT 5.7L Flywheel Noise VIN: 1D7HU18288
THE CUST DECIDED NOT TO FIX TRUCK AND TRADED IT IN SORRY IT TOOK SO LONG BUT I DID GET TO SEE THE TRUCK AND HEAR THE NOISE AND I AM 95 PERCENT THAT IT WAS THE TORQUE CONVERTER THAT WAS BAD
8
Prev (Also Available: All, Asian, Chrysler, European, Ford, GM.) Next