Join Now
International Automotive Technicians Network
Prev Professional Automotive Repair Technical Discussions for January 22, 2015
International Automotive Technicians' Network (iATN) - Members Only
Next
(Also Available: All, Asian, Chrysler, European, Ford, GM.)
Vehicle Owners: If you are seeking an automotive repair professional to service your vehicle, visit the iATN Repair Shop Finder.

Open Help Requests for Chrysler
Help Request Answers
1996 Dodge Dakota 3.9L No Start VIN: 1B7GL23X7T
auto came in intermitted stall. would start right back. found code for ign. coil. replaced coil code never came back. also found alt. not charging. replaced alt. checked good now. customer took auto came back saying no start and sometimes starts and stalls. ra...
View
2001 Dodge Dakota Sport 4.7L Transfer Case VIN: 1B7GG2AN71
This Dakota is electric shift 4X4, it will not shift as commanded. It has a 3-position dial (2WD, 4HI & 4LO) as well as a neutral button. When attempting to shift, the light for the desired range just blinks, it never shifts, or even tries to shift. The TCCM d...
View
2002 Dodge Caravan SE 2.4L Throttle Position Sesor/Transaxle VIN: 1B4GP25B62
Hello everyone and good morning. This post is DEFINITELY for someone that has run into this problem or has seen it before. I looked on IATN and the ONLY possibility I have seen is a post from someone that said they replaced oxygen sensors to fix it. How they f...
View
2005 Dodge Ram 3500 SLT 5.9L MIL Lamp on, Derate VIN: 3D7LS38C05
New customer. According to customer, He bought truck used from a dealer, The dealer had reflashed ECM and put in one new injector. After some problems he had an independent shop pu on new injectors and tubes. While driving, occasionally the MIL and the wait to... Trouble codes: P1222 (Excessive fuel return.)
View
2006 Dodge Ram 3500 ST 5.9L Noise in transmission VIN: 3D6WX38C96
This truck has a scratchy noise in neutral with clutch pedal up push down stop input shaft turning no noise, how ever if wheels are turning the noise stays in neutral clutch pedel up or down. Noise also in Rev,2nd 4th 6th. No noise at all in 1, 3rd or 5th gear...
View
2007 Dodge Ram 3500 ST 6.7L 5th gear VIN: 3D6WH48A77
This truck has the AS68RC Aisin Trans. It came in with several clutch packs wiped.Customer was running a programmer and we assumed the packs were wiped from to much torque.We rebuilt the trans and now it shifts fine but we still have trouble with K3 slipping i...
View
2007 Dodge Caliber SXT 2.0L Final drive VIN: 1B3HB48B97
Hello fellow techs and thanks in advance for your valued input. My customer experience a loud grinding noise which was loud enough to send shivers down your back. Kind of like fingernails on a chalk board! The loud noise went away but now there is a growl. On ...
View
2006 Jeep Commander 3.7L Unknown VIN: 1J8HG48K96
rebuilt transmission replaced vavle body replace tcc two times transmission goes in and out of overdrive at 30- 35 mph anybody had this problem
View

Fixes & Summaries for Chrysler
Fix/Summary Answers
2007 Chrysler Pacifica Touring 4.0L Battery VIN: 2A8GM68X37
After many painful hours the customer pulled the plug on my diag because her Mom needed her car back and she didn't want me to spend the time to fix it. I know it's the IPM, I know it is. It has to have an internal short to ground. Under the IPM is a green...
10
2003 Dodge Grand Caravan SE 3.3L Starting VIN: 2D4GP44R73
upon further looking we found a couple wires that a mouse had gotten a hold of. Repaired wires and still no luck. Inspected all connectors under fuse box and did not find any problems, thoroughly inspected all wiring harness, pcm connectors and powers and grou...
11
2013 Dodge Journey SE 2.4L ASD A circuit VIN: 3C4PDCAB1D
Disassembled PDC to take a closer inspection, where I found serious corrosion in the printed circuit board, right next to the PCM/TCM relay,there were also burn marks around that area fusing the circuits together, explaining why the vehicle would start with th...
4
Prev (Also Available: All, Asian, Chrysler, European, Ford, GM.) Next