 Prev |
Professional Automotive Repair Technical Discussions for September 15, 2014 International Automotive Technicians' Network (iATN) - Members Only |
Next  |
| (Also Available: All, Asian, Chrysler, European, Ford, GM.) | ||
| Vehicle Owners: If you are seeking an automotive repair professional to service your vehicle, visit the iATN Repair Shop Finder. | ||
Open Help Requests for European
| Help Request | Answers | |
| 2006 BMW M5 5.0L comfort access VIN: WBSNB93566 Hello everyone and thanks for the help. This Bimmer came in for a complaint of losing time/date and trip resetting. Found a parasitic draw. With the help of ICOM found faults for the drivers door handle and alarm siren. replaced these and attempted full car en... |
View | |
| 1997 Jaguar XK8 4.0L Stall, no acceleration VIN: SAJGX5749V this vehicle came from a different shop. the owner complaining of now power and stalling. it had the codes listed for cam and crank sensor. they replaced both and it did not change the performance. i looked at vehicle. there are no codes presently. i was tryin... Trouble codes: 0335 (crank sensor), 0340 (cam sensor) |
View | |
| 1997 Jaguar XK8 4.0L shift interlock VIN: SAJGX2748V Customer had vehicle towed in because she couldn't get out of gear. After experiencing complaint we took the shifter cover off and checked for power to shift lock solenoid, there was no power going to solenoid.we checked fuses and fuse #7 on the drivers side f... |
View | |
| 2002 Mercedes-Benz ML320 3.2L fuel system VIN: WDC1631132 this is a ml270,2.7 5cyl diesiel,starts drives well,idles good,no codes,put into drive or reverse, idle increases.exess black smoke from exhaust,reading data from das machine only thing out of whack is the injection quantity at idle should be 5-6 actual is 4,p... |
View | |
| 2009 Mini Cooper S 1.6L MIL Lamp on VIN: WMWMF73529 Hi, I have a 2009 Mini Cooper S. N14 Engine, arived with engine noise (3qrts low on oil) MIL on. Topped up oil and cleared codes. Now vihicle has no power/reduced eng perfomance and keeps setting fault 296A. Inlet Camshaft sensor, (Faulty Phase Position). The... |
View | |
| 2009 Volkswagen Jetta TDI 2.0L Egr VIN: 3VWRL71K39 Hello techs this jetta throws code p045e-egr #2 stuck open i have replaced both egrs cleared code returns instantly is this throwing this code due to something else wrong like the dpf???has anyone come across this if so any help is great thanks |
View |
Fixes & Summaries for European
| Fix/Summary | Answers | |
| 2002 Audi A4 1.8L abs VIN: WAUJC68E92 Sorry for the late close. sent the ABS module out for repair. could not be repaired. installed new ABS repair kit at pump. could not code the steering angle sensor, so we had to replace that too...coded system, all good now. Thanks! |
6 | |
| 2008 Audi A6 3.2L Eng. Codes VIN: WAUAH74F98 thxs for everyones help..what we have found is that all vacuum lines were good and no intake leaks where found..we had to re-flash the pcm and body control modules with new updates fixed the problems!!! |
7 | |
| 2007 BMW 328i 3.0L Mechanical VIN: WBAVC53547 Hello guys, thanks for your help on this one. We replaced complete valve cover because the PCV system is integral to the cover and there is no way you can replace just the pcv it’s sealed in. For the mixture codes we replaced eccentric shaft sensor. Reprogramm... |
4 | |
| 1988 Mercedes-Benz 560SL 5.6L MIL Lamp on VIN: WDBBA48D1J Thanks to all ! With the replies, and especially the most excellent article Steve Brotherton wrote for Import Car,2/2001, I was quickly able to diag.and repair the car with a replacement ECU. Pin #3 of the round diagnostic connector,X11,can be read with a ... |
4 | |
| 1976 Volkswagen Super Beetle 1.6L Excessive Emissions, Hesitation Done! Following Clay [...]'s advice to go ahead & tighten spring tension on air door in AMM a couple notches & started seeing readings coming down. Ended up 20 notches tighter, 'bout three turns out on CO adjustment screw for final readings of 2.2% CO, 120 on HC. ... |
21 | |
| 2002 Volkswagen Passat GLX 2.8L Poor Idle Quality, Misfire VIN: WVWRH63B72 Thanks everyone for all your feed back... we were all pretty much on the same page. ended up advancing the b2 intake cam one tooth. all faults cleared, cam was reading -6 instead of -25. Trouble codes: P0300 (Random missfire), P0301, P0302 (Cyl 2 missfire), P0303 (Cyl 3 missfire), P1347 (Cam/crankshaft correlation bank 2). |
7 |
