 Prev |
Professional Automotive Repair Technical Discussions for February 22, 2012 International Automotive Technicians' Network (iATN) - Members Only |
Next  |
| (Also Available: All, Asian, Chrysler, European, Ford, GM.) | ||
| Vehicle Owners: If you are seeking an automotive repair professional to service your vehicle, visit the iATN Repair Shop Finder. | ||
Open Help Requests for Chrysler
| Help Request | Answers | |
| 1996 Chrysler Concorde LX 3.3L speedometer VIN: 2C3HD56T0T The speedo on this one came in jumping around and then went dead. The output speed sensor has a good pattern and ohms out good. After extensive testing I found that my signal going from the TCM to the PCM was not right. It is supposed to be a square 5v pattern... |
View | |
| 2005 Chrysler Town & Country LX 3.3L instrument cluster and radio VIN: 2C4GP44R15 This condition is very intermittent - it happens for everyone except a tech. We have seen problems in the past with TIPM's but cannot verify this. Have seen wiring harness issues, but also not the case. Power and ground circuits function properly when we test ... |
View | |
| 2005 Chrysler 300 Limited 3.5L Transmission VIN: 2C3JK53G75 First time asking for help here... Car came in with check engine light on and transmission was in limp mode (1st gear). Car has all wheel drive. Codes: po717- input speed sensor 1 ciruit no signal, p0657- solenoid supply voltage circuit, p0710- transmission ... |
View | |
| 2005 Chrysler Sebring Touring 2.7L Surge VIN: 1C3EL56R85 HI Chrysler Guys I am helping out our apprentice with a Sebring that has a terrible surge at steady cruise around 1750 rpms. It cuts in and out constantly if throttle held steady. At first we thought maybe lockup convertor but it seems to eratic. I did find if... |
View | |
| 2007 Jeep Compass 2.4L Timing Chains VIN: 1J8FF47W27 I cannot seem to pinpoint the noise/rattle. I'm thinking that the timing chain and balance shaft chain may need replaced. Not sure if that is the correct direction to go. Has anyone run into this noisy critter yet? Thanks in advance. Mike. :) |
View |
Fixes & Summaries for Chrysler
| Fix/Summary | Answers | |
| 2004 Dodge Dakota SLT 4.7L Misfire VIN: 1D7HG48NX4 Thank you for all of your replies. We removed the passenger side head and had the valves redone. The vehicle now operates normally. God Bless. Trouble codes: P0308 (Misfire--Cylinder 8). |
19 | |
| 2005 Dodge Grand Caravan SXT 3.8L Prndl VIN: 2D4GP44L65 after working on the tcm the problem appears to be very much less and customer will drive until we can try a used tcm module. i wish to thank all the people who tried to work with us and will post a repair when we have a true answer. |
7 | |
| 2007 Dodge Magnum SE 3.5L MIL Lamp on VIN: 2D4FV47V07 The local Chrysler dealer first said they found the camshaft gear wobbling, and said nothing they did before caused the problem we have now. (of course) They said the car needed a camshaft sprocket, camshaft thrust seal, and camshaft thrust plate. I told them ... Trouble codes: P0016 (Crankshaft / camshaft timing misalignment - bank 1 / sensor 1). |
9 | |
| 2007 Dodge Ram 1500 TRX4 5.7L gas cap VIN: 1D7HU18217 Hi everyone thanks for the help and guidance. When I got the truck today the message did not appear so I went into the cluster with the scan tool and reset the ecu thanks to all for your help. |
8 |
