Join Now
International Automotive Technicians Network
Prev Professional Automotive Repair Technical Discussions for October 8, 2011
International Automotive Technicians' Network (iATN) - Members Only
(Also Available: All, Asian, Chrysler, European, Ford, GM.)
Vehicle Owners: If you are seeking an automotive repair professional to service your vehicle, visit the iATN Repair Shop Finder.

Open Help Requests for Chrysler
Help Request Answers
2002 Dodge Dakota SLT 3.9L No Start VIN: 1B7HL48X42
This truck came in with a crank no start condition. The odometer says No Bus. I suspect the skim module, because I have no communication with any of the modules and the IPC doesn't come to life, even the gauges do not work. I cant find any way to test the SKIM...
2004 Dodge Stratus SE 2.7L MIL Lamp on VIN: 1B3EL36T44
this was a car bought at an auction no history on it,had evap codes that we repaired now p1195 comes on after driving cat drive cycle,o2 sensor has been replaced by us allready still same problem. Trouble codes: P1195
2004 Dodge Grand Caravan C/V 3.3L Poor Idle Quality, Hesitation, Surge, Stall, Misfire, MIL Lamp on VIN: 1D4GP24R35
went back and checked harness melted wire insulation about 7 wires involved corrected to still no availbeleive it still has a wire issue.but i went through this on a 960 volvo and there were 3 dead cyl not firing and it was a stepper motor at fault for the vol... Trouble codes: 2305 (secondary ign ckt fault), 2306 (secondary ign ckt fault)
2006 Dodge Caliber 2.0L No Throttle response VIN: 1B3H3G8B97
Please could anybody supply the expected voltage values at the throttle pedal.We have at the moment App1 .44 volts to 4.37 at WOT . App2 .44 to 2.19 volts at WOT. This data read at the throttle pedal and at the ECU with multi meter,and is also supported by the...
2006 Dodge Charger 2.7L MIL Lamp on VIN: 2B3KA443R6
Car came to shop with overheating problem. Testing confirmed that coolant was being forced out of cooling system. Removing cylinder heads confirmed suspicions. Head gasket was breached between #1 & #2 cyls, and the cooling ports. Replacing head gaskets seems t... Trouble codes: P0016 (cam/crank correlation)
2006 Dodge Stratus SXT 2.4L MIL Lamp on VIN: 1B3EL46X96
This car came in for a MIL and a noise at the front of the engine. I pulled two TPS codes, I can't remember which, I diagnosed and replaced the TPS and those codes are gone. I found the belt tensioner was noisy with a stethescope. I removed the drive belt and ... Trouble codes: P0016 (CKP/CMP Timing Misalignment/ Out Of Sync.)
1997 Jeep Grand Cherokee Limited 5.2L Cuts out, Misfire, MIL Lamp on VIN: 1J4GZ78Y7V
This is my personal vehicle in which I try to maintain. Two weeks ago jeep overheated due to faulty seam in radiator. I put new one in and all was well for about a week, when fuel pump went out. After pump quit,and new pump put in, motor still missfiring on co... Trouble codes: P0301

Fixes & Summaries for Chrysler
Fix/Summary Answers
2005 Chrysler PT Cruiser Touring 2.4L Excessive Emissions, Hesitation, MIL Lamp on VIN: 3C3EY55E95
This new turbo leaked oil ant it got on the 02 sensor and the intake sensors. Mass air flow, air idle control, and even the map sensor. When I replaced the pcv valve which had hair line cracke in it, the code didn't come up for a much longer time. I beleive th... Trouble codes: P0171 (Lean bank one).
2001 Dodge Ram 1500 Truck 5.2L no overdrive VIN: 1B7HC16Y31
This truck it fixed!!! First I just want to thank everyone for chipping in! I must give Randy most of the credit though. Sir I am not sure how I would have navigated this without your tireless help. I must have sent this man 50 e-mails and I got a ton of h...
2002 Dodge Ram 1500 Truck 4.7L Water Pump VIN: 3D7HU18N92
Well, Seems To Be OK Now. After 2 "New" Aftermarket Pumps, 1 Reman. Pump & 3 Ruined Belts, I Installed The Original Pump Off The Original Engine With 171,000 Miles On It And So Far It's Working Fine. I've Used Enough Aftermarket Pumps In The Past And Never Had...
1999 Jeep Grand Cherokee Limited 4.0L security system VIN: 1J4GW68SXX
The consenses was to replace the skim module and get new keys. I had a new module but didn't have new key and I couldn't get it to program with the old key. Instead of waiting for a new key I told the customer to go to local Jeep dealer and have them do it. Th...
Prev (Also Available: All, Asian, Chrysler, European, Ford, GM.) Next