× Auto Repair Pros Member Benefits TechHelp Knowledge Base Forums Resources My iATN Marketplace Chat Pricing About Us Join Industry Sponsors Video Members Only Repair Shops Auto Pro Careers Auto Pro Reviews
Join Now
International Automotive Technicians Network
Prev Professional Automotive Repair Technical Discussions for September 15, 2011
International Automotive Technicians' Network (iATN) - Members Only
(Also Available: All, Asian, Chrysler, European, Ford, GM.)
Vehicle Owners: If you are seeking an automotive repair professional to service your vehicle, visit the iATN Repair Shop Finder.

Open Help Requests for Chrysler
Help Request Answers
1985 Chrysler Laser XE 2.2L Poor Idle Quality, Hesitation, Surge, Misfire, Poor Fuel Economy VIN: 1C3BA54E3F
hey guys. I need some help with this one. This one came in for a low power during acceleration and rough idle. I checked the timing with the ect sensor disconnected and it's @ +15deg, so I adjusted down to 12deg, no change. Checked spark plugs and it had Bosch...
2006 Dodge Ram 2500 SLT 5.9L MIL Lamp on VIN: 3D7KS28C96
Hi Dodge techs, We have 1 here thats stumping us. We've looked at all the previous post on this and went through this turck here, but the check engine light still comes on after the second test drive. The engine runs fine, we scoped the camshaft and have a goo... Trouble codes: P0341 (camshaft)
2007 Dodge Caliber SXT 2.0L fuse 34 abs valve supply voltage VIN: 1B3HB48B67
Hello folks, I have a Caliber here blowing fuse 34 in the front distribution block. My diagram seems like its missing something. From what I can tell, it looks as if this supplies battery voltage to the valves in the abs unit. Im wondering if what, if anything...
1999 Jeep Cherokee Sport 4.0L Poor Idle Quality, Surge, Intake Air Noise VIN: 1J4FF68S2X
During warm up the engine starts running rough and the intake air gets very very loud. The air through the intake sounds like a tornado. As the engine warms up the engine starts to run better and the intake noise quiets down. Even when cold the engine must run...
1999 Jeep Grand Cherokee Laredo 4.0L Hesitation, Stall
I have a 99 jeep grand cherokee in the shop that hesitates when cold. It acts like it has low fuel pressure but it holds 45psi when it happens. After about 3 minutes, it runs fine. Let it sit for an hour and then drive it , it will happen again. No codes. Tps ...

Fixes & Summaries for Chrysler
Fix/Summary Answers
2002 Chrysler Town & Country LX 3.8L Blower motor speed VIN: 2C8GP64L02
I think this has been fixed. The customer has not been back since we replaced the blower module/resistor assembly with a "Mopar" Chrysler assembly. I talked with the IdentiFix tech and did some testing. I put a headlight across the power and ground to the modu...
2004 Chrysler Crossfire 3.2L Limp In Mode VIN: 1C3AN69L34
TCM had ATF in it...Got in thru harness...New TCM & Adapter plug...cleaned harness...so far so good... Ron
2005 Chrysler PT Cruiser Classic 2.4L Hesitation, jerking VIN: 3C3FY45X45
Thank you everyone for your replies, I have located the problem, and it has been corrected. The brand new cam position sensor out of the box was no good, I noticed that after the 15 minute road test, and the code setting, when checking voltage at the cmp conne... Trouble codes: P0344, P0517.
1998 Dodge Grand Caravan ES 3.8L MIL Lamp on, inoperative VIN: 1B4PG54LXW
Hi, I have not yet repaired this vehicle, but I know what the problem is. It has a bad connection on the circuit board for the guages. Some have suggested that it can be repaired if you take it out and resoldier it. That would be my first option before fin... Trouble codes: P1695 (No Body CCD message), P1698 (No Trans CCD message).
2001 Dodge Ram 1500 Laramie 5.2L cluster VIN: 1B7HF13Y81
After replacing pcm I still had the same voltages on bus wires so I was able to get a used cluster which I installed with no change! I at this time started over and found every module on the bus and started checking all the wires involved what I found was the ...
1994 Jeep Grand Cherokee Limited 5.2L Radiator VIN: 1J4GZ78Y3R
Going to tear it back down and send heads back out to a different machine shop will post later after all repairs are done
Prev (Also Available: All, Asian, Chrysler, European, Ford, GM.) Next