 Prev |
Professional Automotive Repair Technical Discussions for June 23, 2011 International Automotive Technicians' Network (iATN) - Members Only |
Next  |
| (Also Available: All, Asian, Chrysler, European, Ford, GM.) | ||
| Vehicle Owners: If you are seeking an automotive repair professional to service your vehicle, visit the iATN Repair Shop Finder. | ||
Open Help Requests for Chrysler
| Help Request | Answers | |
| 1999 Chrysler Intrepid 2.7L blower motor VIN: 2C3HH46R0X OK Chrysler techs I need some help on this one. So thanks in advance for all replies. My customer came in with the concern that his blower motor will only work on high regardless of mode or temperature. This vehicle is equiped with MANUAL TEMPERATURE CONTROL. ... |
View | |
| 2001 Chrysler Town & Country EX 3.8L Electronic VIN: 2C8GP4431R Need some help on this crazy Chrysler. This is a Town& Country, Several things going on, Code 1790 only, this is only supposed to set with other codes???. The speedo goes crazy when setting still, this also happens if in any gear other than park and the hvac u... |
View | |
| 2000 Dodge Dakota Sport 4.7L No Start VIN: 1B7GG2AN3Y Car was towed in with a no-start complaint! After investigating I found connector C-3, pin 12(asd sense) melted . This car has been worked on by 2 other shops.When you install a working ecm , it will run great for 5 minutes. Then you'll get a very slight mis-f... |
View | |
| 2000 Dodge Dakota Sport 4.7L MIL Lamp on VIN: 1B7GG22NOY engine seems to start and run ok most of the time Trouble codes: 1391 (loss of cam or crank sensor) |
View | |
| 2008 Dodge Dakota SLT 3.7L limp mode VIN: 1D7HE22K98 vehicle limped in with a P1745. we replaced the line pressure solenoid and line pressure sensor. truck still has same problem. immediately triggers the MIL with a P1745, and goes into limp mode. HELP!!! |
View | |
| 1998 Jeep Grand Cherokee Limited 5.2L Vehicle Speed Sensor VIN: 1J4GZ78Y8W Vehicle came in with a PO720. Scan tool data showed normal mph and output shaft speed sensor. Told customer possible output shaft speed sensor. Replaced OSS with new one. Cusomer brought back same problem. Installed new VSS. Same problem. When vehicle is actin... |
View | |
| 1999 Jeep Grand Cherokee Laredo 4.7L No Start VIN: 1J4GW58N6X Hello fellow techs. I have a question that I hope some Jeep techs can help out with. I just installed a used engine into this 99 Grand Cherokee. Now it will not start. The old engine ran, but had a rod knock due to loss of oil. Everythng on this engine was dif... |
View | |
| 2002 Jeep Liberty Limited 3.7L hvac box VIN: 1J4GL58K42 my guy replaced the evaporator because it was leaking, got everything back together and temperature coming out of the vents was only 80 degrees on max a\c. The clutch was going in and out but the pressures are reading okay. replaced the compressor to and recha... |
View |
Fixes & Summaries for Chrysler
| Fix/Summary | Answers | |
| 1997 Chrysler Town & Country LX 3.3L directional and 4 way flashers VIN: 1C4GP54R0V thanks all for your help i ended up replacing the power wire to the combination switch and all is working fine.. |
6 | |
| 2001 Chrysler PT Cruiser 2.4L No Start, Cuts out VIN: 3C8FY43BB1 thanks for those who responded. the fix for this was the instrument cluster. the cluster is the last item on the series/parrallel pci bus circuit. looking back I don't think I would have done anything different. I installed a used one and all is well. full co... |
4 | |
| 2005 Chrysler 300 C 5.7L Suspension VIN: 2C3AA63H55 I have replace the strut rod and found that the noise has gone away. |
11 | |
| 2003 Dodge Stratus SE 2.4L Starting VIN: 1B3EL36X83 Thanks for the help!! I was afraid it would be the range sensor inside the transmission and it definately was. This is the furthest I've ever dug inside a transmission and it really wasn't too bad. Get this- it actually worked when i got it back together! The ... |
9 | |
| 2004 Dodge Caravan SE 3.3L high side VIN: 1D4GP24R04 Replaced the condensor, despite the customer stating it was just put in, and that lowered the high side pressure to 350psi and the added new weather strippping and that lowered it down to 300psi and we let the vehicle go like that. That you all for your help,... |
21 |
