 Prev |
Professional Automotive Repair Technical Discussions for February 18, 2011 International Automotive Technicians' Network (iATN) - Members Only |
Next  |
| (Also Available: All, Asian, Chrysler, European, Ford, GM.) | ||
| Vehicle Owners: If you are seeking an automotive repair professional to service your vehicle, visit the iATN Repair Shop Finder. | ||
Open Help Requests for Chrysler
| Help Request | Answers | |
| 2006 Chrysler 300 Limited 3.5L MIL Lamp on VIN: ZC3KA63H26 First time asking for help. Thanks in advance. I have a chrysler 300 with the Hemi engine. a code appears intermintantly of p0128 witch says thermstat rationalzation. I cleared the code about 2 weeks ago & the customer called back today & said the MIL light ha... Trouble codes: P0128 |
View | |
| 1997 Dodge B2500 5.2L No Start VIN: 2B7HB21Y2V Hi guys, This work van seems to be eating ecms. The vehicle is a no start with no communication with scan tool. I have tested all powers and grounds to ecm pin A2 12 volts, A31,32 solid ground at zero volts. A22 12 volts. I do have 5 volts on pins A17 and B31... |
View | |
| 2001 Dodge Grand Caravan SE 3.3L Poor Idle Quality, Hesitation, Starts then Dies VIN: 2B4GP44R91 I am loosing my mind!!! I have an intermittent hesitation, or stumble, ocasional stall. ONLY on startup if it runs for 15 seconds or more without acting up it will be fine. There are no driveability complaints. Van runs great. Only problem is on startup. I hav... |
View | |
| 2002 Dodge Ram 3500 Van 5.9L No power, idle ok VIN: 2B7KB31Z42 Hello gentlemen, this vehicle is questioning my ability. I must be looking past a problem. The vehicle starts great, cold and, hot, idles good. Both under load and with out load the engine will not rev up, sounds like a blocked exhaust or severely retarded tim... |
View | |
| 2002 Dodge Ram 2500 5.9L Cuts out VIN: 3B7KF23642 with koeo aps volts change perfect up and down wit h the pedal.the problem happens with engine running the aps will drop out to 0 volts.and thus poor throttle response.any quick tests or advice will be appreciated.thank you Trouble codes: P0122 |
View | |
| 2005 Dodge Ram 1500 Laramie 5.7L Instrument cluster VIN: 1D7HU16D15 I have a 2005 ram 1500 that the has a parasitic draw of 1 amp. I narrowed the draw down to the instrument cluster. With the cluster unpluged the draw is 20ma. I replaced the cluster and still have the same problem. something is preventing the cluster from powe... |
View | |
| 2005 Dodge Magnum SXT 3.5L Hesitation, Surge VIN: 2D4FV48V85 Hello techs i have this dodge magnum 3.5 that came in with a broken timing belt.we put new head gaskets and new belt and it runs great but when you drive for 15-20 min this lighting bolt appears and the letters bas near the mph.it had a code for 02 sensor and ... |
View |
Fixes & Summaries for Chrysler
| Fix/Summary | Answers | |
| 1999 Chrysler 300M 3.5L MIL Lamp on VIN: 2C3HE66G6X I AM GOING TO CLOSE THIS FOR NOW, THANKS FOR ALL THE HELP, WE HAVE DONE EVERYTHING THAT WAS RECOMMENDED, WE STILL HAVE THE SAME PROBLEM, THE CODE IS NOT AFFECTING THE OPERATION OF THE VEHICLE, NEXT STEP AND FINAL STEP IS REPLACING THE ECM, I WILL KEEP YOU INFO... Trouble codes: P0340. |
7 | |
| 1996 Dodge Dakota 3.9L No Start, Poor Idle Quality, Misfire VIN: 1B7GG23X6T Thanks for the replies. I believe the PCM was causing the faulty trans temp reading of -83. I noticed that the scan tool has both voltage values & temp readings for all temp related sensors,ECT, IAT & BATT. the voltage reading would change from 0 to 5v when di... Trouble codes: P0711 (Trans temp sensor), P0171 (Lean exhaust). |
6 | |
| 1998 Dodge B2500 5.9L Cuts out, Stall, Misfire VIN: 3B7KF266XW Thanks so much for every ones help. Fuel inj pump was bad. Got a reman from Dodge.Also as a sidebar note, we replaced the cam sensor right behind that inj pump. Can't imagine changing that sensor w/out pump removal. We also installed new crank sensor when we d... Trouble codes: 1693 (DTC detected in ecm). |
11 | |
| 2004 Dodge Ram 1500 ST 4.7L Trans. relay off VIN: 1D7HA16N44 Confirmed excessive amp draw from trans solenoid pack on L/R Solenoid. Normal draw is 6.5A @ 1.5ohms. Measured 1.2 ohms and amp draw of 9.9 amps when loading circuit.Specs.from identifix and determined using average readings from the remaining solenoid circuit... |
9 |
