|Prev||Professional Automotive Repair Technical Discussions for November 12, 2009
International Automotive Technicians' Network (iATN) - Members Only
|(Also Available: All, Asian, Chrysler, European, Ford, GM.)|
|Vehicle Owners: If you are seeking an automotive repair professional to service your vehicle, visit the iATN Repair Shop Finder.|
Open Help Requests for Chrysler
|1999 Chrysler Concorde LXi 3.2L data stream VIN: 2C3HD46T6X
have vehicle in for drivability concern.no noticable changes in idle,power losses,fuel mileage.noticed during initial check that pulse width,cam & crank sync state,dis signal are changing. pulse width is changing from normal idle reading of 15.42 to 246.72 wi...
|2005 Chrysler PT Cruiser Classic 2.4L MIL Lamp on VIN: 3C4FY48B25
Hello Chrysler techs, The PCM was replaced by another shop and I was asked to program it with my DRB 3. I didn't know if it was a can system and needed the Star scanner. I also have the j2534 pass through system if needed. I used the DRB 3 and entered skim cod... Trouble codes: P1602
|2006 Chrysler 300 (Car) C 5.7L Pads and Rotors VIN: 2C3KA63H56
Have a 300C replaced pads and rotors all the way around. Customer came back complaing of squealing coming from brakes when tapping brakes at highway speeds or coming to a stop. We took apart the front and rear brakes re-cleaned all brackets and lubed everythin...
|2004 Dodge Durango SLT 5.7L Mechanical VIN: 1D4HB58D84
brother called me with engine noise complaint, was on cold start. turned engine off, checked oil level-ok. restarted engine with noise & check engine light came on. had vehicle towed. noise is a double rattling noise. no distinctive location is loudest at rear...
|2005 Dodge Magnum SE 2.7L Poor Idle Quality VIN: 2D4FV48T05
After replacing the throttle body with a factory part, the idle will not relearn. Using modis, we go through the relearn process, it says compete. Idle is normal until the car is put in gear then idle rises immediately to almost 2000 rpm. I am wondering if thi...
|1999 Jeep Cherokee Classic 4.0L Starting VIN: 1J4FT68S7X
Customer just bought used vech Sat from dealer drove of lot 12 hours later would not start, AAA tries to jump no go, sprays either starts up, bangs on tank starts runs. Took to his mech changed fuel pump, now when it sits over night it cranks no start as if lo...
Fixes & Summaries for Chrysler
|2001 Chrysler LHS 3.5L Overheats VIN: 2C3HC56G31
Thanks for all the help. After removing the thermostat, we blew through the small hole above the opening. After reassembling the vehicle, when filling the cooling system, it bled and filled faster. Temp staying good. The lo speed fans now come on and go off in...
|2000 Dodge Ram 2500 Truck 5.9L All guages VIN: 3B7KF23Z5Y
Hey Guys Sorry this took so long, we had a hard time with this one. Pretty much everybody that replied said change the PCM. So we ordered a used one because of the 580.00 list price. On the same day we installed it the truck was doing the same thing. But whi...
|1971 Jeep Jeepster Commando 3.7L Excessive Emissions, Poor Idle Quality, Hesitation, Cuts out, Misfire, Poor Fuel Economy, NO OIL TO ROCKERS VIN: 8705F17077
Unfortunately we have not had the vehicle back in the shop. Customer is attempting to get more information for us but that has not arrived, and we are short handed and behind in our other work and he is in no rush. I had hoped to have had some time to go back ...
|1996 Jeep Grand Cherokee Limited 5.2L Poor Idle Quality, Misfire, MIL Lamp on VIN: 1J4GZ78Y3T
Hey all of you I have good news!!!The fix was an injector cleaning.I didnt use the motorvac but a bg kit for it.It did all the diffrence in the world.I still have a light hesitation but I think that engine is on its way out.The cat converter may have been dama... Trouble codes: P0300 (multiple misfire), P0308 (cylinder 8 misfire), P0302 (cylinder 2 misfire), P0305 (cylinder 5 misfire), P0304 (cylinder 4 misfire).
|1999 Jeep Grand Cherokee Limited 4.7L engine VIN: 1J4GW68N3X
thanks to all that replied the problem was a bad crank sensor!the data pids still all read n/a even when it is running still don,t know what the problem is there but the noise they heard is the lower end of the engine is very noisey at hi revs.so we plan to pu...