Prev iATN Members TechHelp for July 31, 2009
Automotive Technical Exchange for the Automotive Repair Professional		 Next
(Also Available: All, Asian, Chrysler, European, Ford, GM.)
Vehicle Owners: If you are seeking an automotive repair professional to service your vehicle, visit the iATN Repair Shop Finder.

Open Help Requests for All Makes and Models
Help Request Answers
2004 Acura MDX 3.5L belt chirp
Hello everyone and thanks for the help on this pesky MDX. Two months ago, we installed a remanufactured alternator on this vehicle because it was not charging. The customer contacted us about a week later and said that she had developed a "chirp" noise. I susp...		 View
1991 Audi 100 2.3L 5 Speed
Hi Guys This high milage 100 Quattro is a daily driver for a very good customer as well as a dear freind. It is a five speed manual tranny that will not go into revers. The shifter feels like it is blocked from moving to the reverse position. I found some pla...		 View
2001 Audi A4 1.8L Converter
I bought a new converter and was told by the dealer that when I install it I have to reprogram/relearn the transmission. He didn't know how I can do this but was insistant that it needed it. Any suggestions or tips?		 View
1987 BMW 325i 2.5L Poor Idle Quality, Hesitation, Surge, Stall, Poor Fuel Economy, MIL Lamp on
In my entire career I have never been as frustrated with a car as I am today. I need the help of A Bmw expert. The car was towed in with these symptoms. The car starts hard, idles rough and hesitates under a load. The check engine like flashes rapidly in conju...		 View
1988 BMW 735i 3.4L rotors
All four wheels will lock up at the same time, the brake hoses, caliber, rotors and brake pads have all been replaced. Once you loosen the line on the master cyclinder the brakes will release. Thinking about changing the master cylinder, or does anyone have an...		 View
1998 Cadillac DeVille 4.6L security
Vehicle towed in with display message "Wait 3 minutes" on cluster...no crank condition vehicle has remote starter installed.. ignition key bypassed/ resistance is ok going to ipc code stored p1632 before going further need to know if anyone has seen this c...		 View
2005 Cadillac STS 3.6L Ignition..
We are repairing a 2005 Cadillac STS for a client, and the vehicle will not start. The Odometer display reads "Starting Disable" Vehicle had some damage to the front end. Engine was not affected. Starter will not turn at all. This vehicle is equipped with the ...		 View
1992 Chevrolet Camaro 5.0L Safety
car came in with air bag lite on . hooked up scanner and it has 2 codes . #24 #34 and i can limited info on lthis. All i can find is low voltage from key on power. Any help or what to check would be great		 View
1992 Chevrolet S10 Blazer 4.3L No Start
OK Chevy techs, this ones for you. While driving on hwy this thing just quit running like the switch was turned off. Towed in and checked for fuel pressure. 45PSi .NPF Just had added gas day the before so I know it's not empty. Fuel pump runs with key on . che...		 View
1997 Chevrolet Astro 4.3L Hesitation, MIL Lamp on
i am experiecing a case of HIV (HAIR IS VANISHING) over this van. It barely runs and has No power at all. once you get it started it takes a few times by pressing the gas pedal on and off to clear it out so it can rev up. If you put it in gear it will only go ... Trouble codes: po341 (cam sensor).		 View
1999 Chevrolet Cavalier 2.4L valve train
thanks in advanced other tech replaced oil pump now code po325 knock sensor and noisy valve train checked tensioner ok but no pressure behind tested oiling system with in spec at idle and 2000 rpm any help would be apreciated checked oil filter ok no blockage ...		 View
1999 Chevrolet Silverado 5.3L 1-2 shift solenoids
Ok , got a weird one here. Customer states that trans started shifting hard, intermittently. He would turn key off and restart truck and would be good to go for several months. Then it seemed like it was slipping for him ?? He would turn key off and restart tr...		 View
2001 Chevrolet Venture 3.4L high idle
hello everybody i need help with a 01 venture 3.4 the problem is it has a high idle the tps reads 2.0 volts at idle and 4.46 at wot the van idles any where from 1200 to 3000 i cant find any vaccumm leaks the iac reads 60 counts at idle if i use the scanner to ... Trouble codes: 121 (tps performance), 122 (tps high), 1122 (tps low).		 View
2003 Chevrolet Express 6.0L No Start, NO COMUNICATION
vehicle towed in as a no run. on initial check, vehicle runs but no gauge operation and alternator light on and vehicle is charging. no scan tool comunication. no power at dlc and fuse good. ran seperate power supply to pin 16 on dlc but still no comunication.		 View
2004 Chevrolet Express 5.3L Mode
This van recently landed in my bay - it has an HVAC mode problem. From what our driver can tell me (it is the parts delivery van) it blows OK in vent and floor modes, but when switched to defrost it will intermittently not blow air out. She says she can't hear...		 View
2000 Daewoo Lanos 1.6L thermastate housing
thanks for any and all help . ok this car came in leaking antifreeze.found the thermastate housing cracked and leaking. verified cooling fan operation they work properly.found NO combustion gases in cooling resivour. checked 4 times. we replace thermastate hou...		 View
1998 Dodge Pickup 8.0L Hesitation, Cuts out
This Dodge V-10 has a manual 5 speed trans. When you shift from second to third and third from fourth it hesitates. Once it gets going it runs good. It seems worse when the truck is loaded. The owner also thinks it has less power then it used to. There are no ...		 View
1998 Dodge Intrepid 3.2L No Start
Greetings fellow techs.I have a funny (not ha-ha funnny) problem with this car.The car was towed in with a broken front strut.As soon as we tried to start and move it into the shop it cranked, ran for about 5 seconds and died.It did this a few times and then w... Trouble codes: none (SBEC communication failure), none (SBEC communication failure).		 View
1999 Dodge Pickup 5.9L brake system
Hi, thanks in advance for any help. Just trying to get some fresh ideas on this one. Vehicle belongs to a landscaping company and initial complaint was brake pedal went to the floor. They checked the fluid and it was empty refilled and almost no brakes. After ...		 View
2003 Dodge Stratus 2.4L Surge, Cuts out, Misfire
the customer states when first started or at a stop light it sumtimes starts to buck or surge only breifly. but runs and drives fine no accel issues or cruising issues only at idle. I rechecked the cam sync and it shows yes no faults no dtc stored. i got it to...		 View
2003 Dodge Pickup 5.9L excessive crank time
Need help from all you cummins diesel techs. We have an 03 Ram 3500 with a excessive crank time after is sits for a couple of hours / over nite. What we found so far is that when the truck is running / cranking the fuel pump is actually pumping diesel out of t...		 View
1997 Ford Taurus 3.0L Poor Idle Quality, P0133 and P1131
Hi Guys and Gals, I have a 2 fold problem here that I'm having trouble making sense of. The complaint was Check Engine light on and intermittent high idle. I started the car up cold and the idle was high. I let the car warm up and connected Auto Enginuity t... Trouble codes: P0133 (B1S1 O2 slow resonce), P1133 (B1S1 O2 Indicates Lean).		 View
2004 Ford Pickup 6.0L Cooling Systems
customer complaints of engine overheat when engine is working hard (loaded trailer). works great under normal driving conditions. replaced engine cooling fan clutch-checked and cleaned radiator. no coolant loss is reported.		 View
2005 Ford Pickup 5.4L Misfire
hey Guys, I'm having trouble with this F150 3 vavle engine. , it misses under heavy load only, ses will being flashing only after the truck is held in the wide open throttle mode for a couple seconds. Other than that it runs normal. Checked and replace coil an... Trouble codes: P0304 (missfire 4 cylinder).		 View
2002 GMC Envoy 4.2L actuator
Complaint of no front-axle engagement in four wheel drive: auto, high, or low. Checked electrical at switch, at transfer case shift-motor, and at front axle shift actuator. All OK. Front actuator works, but front axle just "ratchets". Front driveshaft turns, b...		 View
2005 GMC Envoy 4.2L Hesitation, Stall, MIL Lamp on
Let me start by thanking everyone who replies. After replacing the cylinder head, using special tools to hold the timing chain, the vehicle runs great until the camshaft actuator starts sticking. If it sticks at 0% it runs fine but sets a dtc p0017. If it stic... Trouble codes: p0017 (cam to crank correlation).		 View
1998 Honda Accord 3.0L no green security key
Car was driven into shop and customer said AutoZone checked his MIL and car had a p1706. Also stated an intermittent starting problem. We did the test for continuity on the switch and found a few opens in the switch. While checking the shifter cable for correc...		 View
2000 Honda CR-V 2.0L Fues under dash
The tail lamp fuse fries out when light switch is turned on, pulled out and check all socket asy. Front and rear, replaced all parking light bulbs, front and rear, no change, tried new combo light switch of course Factory New Honda Part, still fries the fuse. ...		 View
2007 Honda CR-V 2.4L Starting
This CRV will not crank at times.It will click with key in crank position,but not crank.Then after 2-3 attempts it will crank and start.This happens a couple of times a month. This is my mother's car,I have never caught it acting up myself. She took it to th...		 View
2001 Hyundai Santa Fe 2.4L Cuts out
Hi Techs, I'm pulling my hair out on this one. After a through warm up, at slow speeds the engine will start fluttering and will die out at a stop, it will restart easy. It did it for me twice in three days and I had the Modis on it the 2d time. The Modis show... Trouble codes: PO421 (cat warm up), PO442 (evap).		 View
1994 Infiniti J30 3.0L engine
First of all I would like to thank IATN for all the fixes I have been able to make with the help of the archives. This car came in hydrolocked and no coolant visable in the radiator. removed plugs and found all plugs to be wet with oilly gas and cyl no 2 to be...		 View
2004 Lexus IS 300 3.0L Misfire
Okay guys so the issue I have is that Ign. coil #3 (closest to the firewall) does not get a ground signal at idle, but when the rpm's are brought up to around 1,200 the signal begins to starts very weak. At 2,000 rpm or more the signal comes on strong just lik... Trouble codes: PO300 (random misfire).		 View
2007 Lincoln Town Car 4.6L mode doors
vehicle cam in with a complaint of poor a/c affect in the rear, upon verifying the complaint another tech found that there was also no control over the mode door, although at random it would move them to any position it choosed. he called the EATC module, i re...		 View
2002 Mazda MPV 3.0L Mulitple Warning Lights
Van nursed in a week ago, customer said it wouldn't start, then did start but ran bad. Started right up once here. Immediately found a loose positive battery connection. Cleaned & tightened: everything fine! No codes: there may have been one or more, but with ...		 View
2005 Mazda RX-8 1.3L Poor Idle Quality, Hesitation, Stall
systems check no codes present or pending. test drove,runs great till it gets warm. after about third short stop seems to load up and run poor. boogs on take off,idles rough,has no power for a few seconds,sometimes stalls,will start ok. seems to run ok after r...		 View
1982 Mercedes-Benz 380SL 3.8L Accessories
Need some help with this one. 1982 Mercedes 380sl with no speedo or odometer movement. My info system is very limited on diagrams. We replaced the vss sensor assembly and still no change. Any one have any tips on diagnosing this speedo/odometer problem. If the...		 View
2003 Mercedes-Benz C230 1.8L Belt Drive
Hay guys, I’m working on a C230 Kompressor that has either a belt tensioner issue or an issue with one of the driven units. In gear, (lower idle) the belt starts flopping around and starts making noise. With the car in neutral, everything smoothes out nicely. ...		 View
2005 Mercury Mariner 3.0L ps line
Trying to replace high pressure hose, you have to take fitting off power steering pump to remove line, new line from Ford does not have new fitting, it is a snap in type end on line, can not figure out how to get line out of fitting.		 View
1991 Nissan Maxima 3.0L alt wiring
Greetings, I received this vehicle with the alt wiring at the battery fuse link cut and the fuse link missing. I am trying to determine why someone would do this to make sure there isn't a short or something going on. Can anyone tell me what the current draw...		 View
2000 Nissan Maxima 3.0L MIL Lamp on
Hello everyone. This one has got us pulling hair. After researching the archives and finding so many fixes about the coils we went ahead and did the repair ...all six coils. The Code 1320 still resets after a short drive. We also checked the harness for shorts... Trouble codes: 1320 (Ignition Primary Fault).		 View
2004 Nissan sentra 1.8L No Start
Hi Nissan gurus, A few hours from a one week vacation and I am stucked with this Nissan for an intermittent no start after pcm replacement. After the replacement of the pcm I redid the initialization of the immu-pcm and the car started right away and everythi... Trouble codes: p1610 (p1614-), p1614.		 View
1993 Pontiac Grand Prix 3.1L Poor Idle Quality, Hesitation, Surge, Cuts out, Stall
Please help me!!! this is one of those nightmares every mechanic hates... they broght this car to me to take a stab at it. it has been to several shops locally but no one has been able to fix it. It idles fine well it actually lopes when it idles but it will i...		 View
2001 Saab 9-5 2.3L sid
Our SID display is very dark and hard to read. If you press the night mode button all the displays including the SID go completely dark and a funny thing also happens is all the instrument cluster needles fall to the off position. Press it again and you can ba...		 View
2004 Toyota Sienna 3.3L Compressor
Customer originally complained of drivers side vents not blowing cold, passenger side is cold. Checked all actuator doors and climate control and all works normally. I thought probably low freon. Evacuate and recharge, sure enough, good cold air both pass and ...		 View
2000 Volkswagen Passat 2.8L pulling
hello this is scott at [...] automotive in san antonio texas,i have a volkswagen passat 30v we are having a problem with pulling on acceleration to the right.we have replaced the motor mounts [all] both axles were bad and have been replaced,the commonly found...		 View
2004 Volkswagen Passat 1.8L MIL Lamp on
Hey VW guys need some advice on this one. Code p0299 keeps returning. WE found oil in air intake which is probably faulty turbo. We cleaned the boost sensor? I think its called (like a MAF). Wiped up as much oil as possible. Drives fine, feels like good boost.... Trouble codes: P0299 (turbo under boost).		 View
2006 Volkswagen Jetta 1.9L Surge, Cuts out, Misfire
Hello VW techs! I have this 06 Jetta from a regular customer. She came in complaining that when she has the cruise on and accelerates with the cruise that it jerks. I test drove to verify and it does jerk and miss. It feels like a bad plug wire but of course i...		 View
2005 Volvo XC90 2.9L MIL Lamp on
This vehicle came to us for the first time on 05/13/09 with a check engine light on. We found the following codes. ECM-120C AIR MASS SIGNAL TOO HIGH ECM-120D AIR MASS SIGNAL TOO LOW ECM-1210 MASS AIR FLOW (MAF)/SENSOR- FLOW TOO HIGH ECM-121B MASS AIR FLOW (MA...		 View

Fixes & Summaries for All Makes and Models
Fix/Summary Answers
2000 Audi A4 1.8L MIL Lamp on
we sent this one off to the dealer. Im not sure how this thing measures the mass air flow of the secondary air but I think that would have been the next thing I would have tried to figure out. Sorry that I dont have more to add. This one really stumped us. ... Trouble codes: p0411 (secondary air injection incorrect flow).		 4
2005 BMW 330Ci 3.0L top cover
thank you scott and joe. what you said is exactly what to do. i stopped cranking when the top was free of the windshield and did not see any more results. that was not enough cranking. when i cranked till it stopped turning, the tension bars were released and...		 2
1999 Cadillac Seville 4.6L No Start
The vehicle was fixed with a new pcm. It acted like a security problem because the passlock 3 couldn't communicate with the pcm. Trouble codes: U1255 (Communication error).		 4
1996 Chevrolet Pickup 5.7L Misfire
First let me say thanks for the great replies I recieved. After reading I decided to R&R the intake to look at the upper and lower gaskets. This also gave me a chance to view the injector tubes. I found no indication of leaking upper or lower gaskets. I did re... Trouble codes: P0134 (p0135-), P0135 (p0137-), P0137 (p0300-), P0300 (p0420-), P0420 (testing and results).		 21
1998 Chevrolet Pickup 7.4L Misfire
many of you guys nailed it. it was a junk aftermarket cap. when i checked resistance there was continuity between 3 and 5. replaced cap and rotor and it ran fine. Thanks a bunch guys.		 12
2001 Chevrolet Suburban 5.3L Poor Idle Quality, Surge
thanks everyone who replied,i gave the costumer a few days to drive the vehicle and so far so good.we only replaced the spark plugs ,the vehicle had brand new autolights we put on ac delco and problem fixed.thankyou iatn.		 10
1995 Chrysler Concorde 3.5L blower motor
Hi all Many thanks to those who replied. I have not fixed this vehicle yet but, I did order a new HVAC control module, everything points to this module.		 3
1997 Chrysler Sebring 2.5L No Start, Poor Idle Quality, Hesitation, Cuts out, Stall
HEY FELLOW TECHS GOT GREAT INFO WHICH WAS BASED ON RESULTS OF TEST I TOOK...FOCUS ON LOW COMPRESSION...REMOVED HEADS AND SENT BOTH OUT AND REPLACED WITH CARE TO BLEED LIFTERS BUT AFTER INSTALLATION HAD NO START AT ALL TIMES COULD NOT GET SPARK FROM THE DIST......		 6
1989 Dodge Shadow 2.5L freeze plugs
I want to thank all who replied. The customer approved removing the cylinder head for further diagnosis and decide whether to fix it or not from there. Most replies recommended a bad head gasket or cracked head and one suggested using a rubber freeze plug. ...		 11
1996 Dodge Intrepid 3.5L No Start
Well after taking all the inputs and applying them the car seems to be fixed. I looked at the crk wires and they were melted together like Kevin suggested. I separated and isolated them and all was fine until it got hot then same old problem. I did try the ici...		 10
2001 Dodge Pickup 5.9L Surge, Poor Fuel Economy
Thanks for all your help, I really appreciated it, but I have heard no response from the owner. I have not been able to reach him. He lives 50 miles away, and I e-mailed him all the 7 answers to no avail. Sorry. Maybe I'll hear something soon		 7
1991 Eagle Summit 1.5L No Start
Thanks for all the help everyone. It turned out to be the ECM. After some more investigating on this problem, I realized that the cam and crank circuits need to have 5 volts on them from the computer, which I did not have. After replacing the ECM, it still wou...		 4
1997 Ford Taurus 3.0L radio, windows
Thanks for all the suggestions. the new trs switch did help, but did not totally solve the problem. I did look in the door wiring harness, found and repaired one broken wire, but no change in symptom. everyone opted to let it go at this time.		 9
1997 Ford Pickup 4.6L window
thanks to all that replied ended up fixing two wires in driver door jam 		11
1997 Ford Econoline 4.2L Poor Idle Quality, Hesitation, Misfire, Poor Fuel Economy
I was on the right track with the converters being clogged. But the power problem ended up being a Mass Air Flow issue. Thanks for the help		 10
1997 Ford Taurus 3.0L erratic shifts
Hi, This car has been sitting outside the shop for a couple weeks now while the owner (dealership) decides what to do. I really appreciate all the replies, and useful information you folks provided. The most common suggestion was to check for a broken accum...		 12
2005 Ford Pickup 5.4L low power
Thanks to the 8 replies that we got trying to help with this vehicle.I very much appreciate the time you guys took out of your busy day to try and help us.What we finally found was timing chain tensioner on right side colasped cause slack in the chain. we also...		 9
2005 GMC Envoy 4.2L No Start, Cuts out, Stall
Thank your you all for your replies. I cleaned the throttle body/plate but the codes kept coming back, i followed the flow chart for code p2135 that led me to changing the throttle body and the vehicle started right up. things i learned while working on this ... Trouble codes: P2135 (tps 1-2 correlation), p2119 (throttle closed position performance), p2101 (throttle actuator position performance), p1516 (throttle actuator control tac module throttle actuator position peformance).		 5
1994 Jeep Grand Cherokee 4.0L Poor Idle Quality, Surge, MIL Lamp on
Sorry for the "no fix". Problem is so intermittent I was unable to duplicate symptom. Apparently it happens once a month. So I check the idle air control valve, cleaned it and cleaned the throttle plates. There was no signs of dist bushing wear, timing chain s... Trouble codes: 13 (No change in map voltage).		 6
1998 Jeep Grand Cherokee 4.0L Pads, Rotors
Thanks for all the replies. This Jeep is finally quiet. NAPA also offers a premium organic pad that did the trick. I had tried a lot of your suggestions including welding and fileing the spindles. Thanks again--Jim		 25
2001 Kia Sportage 2.0L Poor Idle Quality, Hesitation, Cuts out, Stall, Misfire, Poor Fuel Economy
thanks to Matt from Mass. you hit the nail on the head buddy spun crank sprocket. Trouble codes: PO343 (Cam position sensor A circuit high input bank 1).		 6
2005 Kia Rio 1.6L Surge, Stall, MIL Lamp on
thanks to all who took time to reply. Nick hit the nail on the head as well as those who suggested I needed to double check for a vacuum leak.What I ended up finding was someone had adjusted the throttle stop. Once I backed the throttle stop screw one turn the... Trouble codes: po507 (idle air control system rpms higher than expected), po170 (fuel trim bank 1).		 7
1996 Lexus ES 300 3.0L abs system
We've conquered!! Thank you all for the replies. The fix was a left front speed sensor. The really fun part was that we had received a faulty new genuine sensor. I just love when new sensors are faulty, it really makes this whole thing a hoot. Apparently we ha...		 10
1998 Mazda MPV 3.0L No Start
sorry for my late closing due to customer cannot make up his mind,after setting the valve timing engine still will not start,customer decided not to spend any money on this vehicle,problem was the engine low compression well average compression were 115 psi.th...		 7
2003 Mazda Protege5 2.0L Alternator
Thanks for the replies. Seems there are two ways to skin this cat. Fifty-fifty split on the four replies. 2 suggested removing the right front axle, the other two suggested removal from the top. As I had already repositioned a lot of the obstructions up top, I...		 5
2005 Mazda 3 2.3L bearing
thanks for all the help i got some chassis ears found the noise coming from the wheal bearing that i had replaced two times before sow i started to ask ? found out his son has been driving the car for about one month he went home to grill his son found out tha...		 10
1990 Mercedes-Benz 350SD 3.5L Poor Idle Quality, Misfire
We received several very good replies: Steve from Florida wrote: There are various things to look at, but I can tell you a couple things that absolutely won't cause a single cylinder misfire in a MB diesel (of that age). The first is the OVP relay. Electron...		 8
1997 Mercury Mountaineer 5.0L Excessive Emissions
Thanks for the help; this one has passed the emission test. Bottom-line is I replace both front oxygen sensors and it ran through the test just fine. Here is what I have learned: My main goal was to see if there was a trend of bad ECMs, wiring, one O2 taking... Trouble codes: P1131 (o2s b1s1 lean), P1151 (oss b2s1 lean).		 5
2005 MINI Cooper 1.6L electrical issues
Removed the body control module and inspected the board, Found two large burnt spots on the board indicating major issues. I do not have the capabilities to program the module so it went to the dealer. Thanks to all who replied.		 8
2002 Mitsubishi Montero 3.5L No Start
THANKS FOR ALL YOUR REPLIES,THIS VEHICLE IS FIXED,AND RUNNING GREAT.THE FIX WAS A COMBINATION OF BAD GAS,EXTREMELY FOULED SPARK PLUGS,AND CAM GEARS WERE SWITCHED.AFTER GETING AUTHO FOR TEARDOWN,FOUND THAT SOMEONE ALREADY HAD THE T-BELT OFF,AND HAD MARKED THE C... Trouble codes: p0335 (p0340-), p0340 (testing and results).		 5
2003 Nissan Sentra 1.8L MIL Lamp on
We retested and found the ecm not grounding the heater circuit. We replaced with a used ecm and all is well. Thanks for the help! Trouble codes: p0031 (ho2s1 heater control circuit low).		 4
2004 Nissan caravan 3.0L MIL Lamp on,
Thanks to replies. We have overhauled the injector pump and it also needed a new ecm.All good now. These engines seem to be a problem and the injector pumps are a very common repair. Starter motors are also a known problem.We could not communicate with the pum... Trouble codes: 75 (ps-pump control modual).		 3
2000 Other European Corniche 6.7L hydraulic lines
I never did find the part # for MB replacement for the lines I took the advice from Gene [...] & had lines made at a local hydraulic shop. The good news is these lines will out last the car. This car is down the road thank you very much 		2
2004 Porsche 911 3.6L Misfire
It looks like a lifter problem at this point. There is an aftermarket warranty company involved, so I don't expect to be completing this for probably another week. I will keep you posted. Thanks for all of the input. It always helps to get word of someone else... Trouble codes: P0304 (Cylinder number 4 misfire).		 4
2006 Porsche Cayenne 4.5L front subframe/axle support
Thanks for the help. One suggestion was to shift the subframe while on an alignment rack. This would be prefered but was not a possibility because it wasn't done in house and the alignment shop didn't want to touch the subframe. The dealer wanted $400 to look ...		 3
2004 Saab 9-3 2.0L MIL Lamp on
I cleared the codes and the vehicle left and hasnt come back. Thanks for all the replies. I was very close to putting a new throttle body in but the customer hasnt complain about the MIL coming back yet.		 3
2004 Saturn Vue 3.5L Compressor?
Thanks to all who responded.After much research and phone calls, we installed a New Saturn /Supplied "updated" compressor that was a revision of the original we installed. Vehicle has been out 4 days, and client has said aok at this time. Note. The original un...		 5
2004 Saturn Vue 3.5L A/C compressor
Hi all, after put three Reman compressors, same result, no compression at idle, ordering compressor thru LKQ, put it in, everything works fine, some how the rebuilder could not rebuild Saturn Vue compressor! Thanks alot for all hour help.		 4
1999 Toyota Camry 3.0L engine
Thanks for all the replies. After not being able to identify a leak from anywhere... We put the whole thing back together except using a new crank seal as a precaution. The cam seals had dust on them and were dry as they come. Our suspicions are that there...		 9
2001 Toyota Camry 2.2L Hesitation, Misfire
lower crank gear was damaged in keyway. new gear and key. good to go Trouble codes: po300 (random missfire), 301 (cylender 1), 302 (cyl 2), 303 (cyl 3).		 8
Prev (Also Available: All, Asian, Chrysler, European, Ford, GM.) Next