Prev iATN Members TechHelp for July 29, 2009
Automotive Technical Exchange for the Automotive Repair Professional
Next
(Also Available: All, Asian, Chrysler, European, Ford, GM.)
Vehicle Owners: If you are seeking an automotive repair professional to service your vehicle, visit the iATN Repair Shop Finder.

Open Help Requests for All Makes and Models
Help Request Answers
1995 Acura NSX-T 3.0L MIL Lamp on
Hello all I got this NSX from one of my regular customers he had it at the dealer and they replaced all six injectors and an oxygen sensor. Less than one year ago and 2000 miles ago I replaced plugs with oem spec NGK,s. On his way to my shop to pick up one of ... Trouble codes: p1201 (misfire cylinder one), p1204 (misfire cylinder four), p1300 (random misfire).
View
2004 Audi A4 3.0L Clutch Slave cylinder
Removed and replaced clutch and pressure plate. had to disconnect the hose that goes to the slave cylinder to remove the transmission. after installation of transmission and clutch. the slave cylinder will not bleed. used pressure bleeder and vacuum bleeder at...
View
2004 Audi A6 4.2L MIL Lamp on
Hey guys, this RS6 V8 twin turbo is a tight fit. For this code is says to replace the catalyst. The first item in the manual says to REMOVE ENGINE! Queations - Is there a reflash for this code? I know on the 2.7 biturbo's they had a reflash for this but I can'... Trouble codes: p0431 (warm up catalyst b2 below threshold intermittent).
View
2006 Audi A6 3.2L ilumination
Hi Audi Friends, on this car almost all LED's are burned out for the ilumination of the speedo- and rpm meter. At night it is so bad you hardly can read the numbers. According to Audi you have to buy a new cluster + coding. Anybody out there has attempted to ...
View
2002 BMW 330xi 3.0L dash warning
hello thanks for your time .i have this 3 series bima, the dash shows one of the rt rear lites out ,as many of them do. ive seen a few. but no lites are out . is there a bulb ck relay that goes out or something to that effect? i have look in achikves found not...
View
2005 BMW 330Ci 3.0L top cover
owner brought car in with non latching top cover. top goes up and down fine, the cover just does not latch. checked latch motor and found cables broken. removed cables which required motor assy. and latches to be unbolted fron body. while waiting for cables to...
View
1991 Buick Skylark 2.5L Stall
HELP GM TECHS!!This one is eating me alive. Runs great and accellerates all day long. When coming to a stop it stalls. When it first came in we verified the complaint several times. When we got the chance to hook up the pressure guage it had 11psi and then ama...
View
2003 Buick LeSabre 3.8L MIL Lamp on
This car came in yesterday. Sometimes it runs great and then the door chimes go off and the mil light comes on with the traction contorl light as well. When these lights are on the HVAC control head blacks out and the A/C is inoperable. When I first checked fo... Trouble codes: P1571 (TCS PWM circuit no frequency signal), U1040 (Lost communication EBCMEBTCM), P1689 (TCS deliverd torque fault), U1255 (Loss of class 2 communication).
View
2006 Buick Rainier 4.2L rear speed signal
Hello, Customer complaint Right Rear brake grabs. Did rear brake inspection (disc with drum parking brake). Looked ok slight axle seal leak. (don’t think a parking brake can grab from the leak) 1.Put on Scanner NO SPEED SIGNAL FROM RR REAR sensor. 2. Only hist...
View
1994 Cadillac DeVille 4.9L compressor
we have this deville in for replacement of comp, dryer e-tube and condenser. compressor was locked up. on start up with freon in the system the compressor came on for a couple of seconds and not since. we have tried the battery disconnect and have found no cod...
View
1997 Cadillac Eldorado 4.6L detonation
Thanks in advance for all that are willing to help on this one. When this car is hot the engine pings under slight acceleration. You can power through it if you mash it to the floor. Fuel pressure is within specs. I have no codes. I can check the egr operation...
View
1997 Cadillac Seville 4.6L battery
GOOD EVENING EVERYBODY.I have a customers car that if it sits three or four days the battery goes dead. After reading all the posts it seems there is alot that could be drawing from the battery.I know i do have a draw but having a hard time telling how big of ...
View
1999 Cadillac DeVille 4.6L no starter
can the ignition switch pass key system keep the starter fron ingaging. i can jump purple wire at intake and will start and run a second. will do the same from starer relay.i went to check car thinking could start it because he said battery was low.do not have...
View
2000 Cadillac Catera 3.0L abs,tcc,speedo
has codes b1552,b1558,b1983,b2420,b2473,v1128,v1255,v2108,p1700
View
2004 Cadillac SRX 4.6L MIL Lamp on
I have a 2004 Cadilat SRX in the shop that keeps coming back with P0172,P0175 codes.Acording to costomer tune up was done 20k miles ago with ac delco plugs. I replaced both upstream o2 with bosch with are same ones it had before. Replaced mass air flow sensor ... Trouble codes: P0172 (bank1 rich), P0175 (bank2 rich).
View
1997 Chevrolet Cavalier 2.4L none
thanks in advance,the poping noise happens when moving forward or backward on uneven surface.we have put chasis ears on the strut,trans case,lower control arm,tierod,steeringrack and left side body sections and noise seems to be in and around the strut/axle ar...
View
2005 Chrysler 300 5.7L transmission speed sensor
Transmission goes into limp mode very intermittently. Sets codes P0700 trans issue, trans P2767 (active code) input speed sensor #2 CKT error, P2638 (stored) torque management feedback signal performance. Customer drove in broke so we hooked up to it while sti...
View
1996 Dodge Grand Caravan 3.3L Brake pedal
hello, van came in with front brakes grinding and complaint of dropping pedal. we changed front pads and rotors.tried the pedal after, it feels good when van is off.turn van on the pedal drops almost to floor.we relaced master cyl.,same took look at rear brake...
View
1997 Dodge Grand Caravan 3.3L No Start
engine will not start good fuel pressure no spark set po320 code replaced crank sencer still will not start need help
View
1998 Dodge Pickup 5.9L Misfire
Hey guys (and gals :)...) We have a 1500 Ram with a intermittent misfire and stumble at idle. when misses throws P0306. Have done complete tune and replaced injector. Compression test tests out within specs. Customer wants to to change PCM. We are not sure. Co... Trouble codes: P0306 (Cylinder 6 misfire).
View
1998 Dodge Ram Van 3.9L Misfire
need help on this one, dodge ramvan 98 3.9l v6 does misfire on cruise on all cylindre especialy on #1-3-5 cyl. change intack gasket because of leak, cam and crank sensor ave been already change from another garage.already clean injector and see them work prope... Trouble codes: p0300 (p0301-), p0301 (p0303-), p0303 (p0305-), p0305.
View
1998 Dodge Intrepid 3.2L gas guage/ IPC
Vehicle came in with complaint of fuel guage inop, and all the warning lights on on dash. Also notice A/C comes on without turning switch on. Found many codes in all modules, mostly comunnication codes. Found concern is worse after setting over night on first ...
View
2000 Dodge Durango 4.7L blower
i have power out of the blower but the control head has no ground. if i put a ground i have blower and the center console lights work. also the control head stays lighted up with key off until you ground that black wire. the wire goes behind the dash, so befor...
View
1994 Ford Ranger 2.3L Mechanical
Truck came to me with a normal feeling pedal but when you drive it and come to a stop you have to pump the clutch to make it release. After inspection I discovered the fluid to be contaminated so I replaced the Master Cylinder and it seem to get better for a f...
View
1994 Ford Pickup 7.3L Excessive Emissions, white smoke
this truck is blowing excessive white smoke when first started and continues to blow lots of white smoke at all rpms. seems to thin out a bit when the truck gets warm. haven't changed the thermostat yet but the truck is only running at 170 degrees. if i crack ...
View
1995 Ford Explorer 4.0L Crankshaft dampner pulley
Greetings Ford Wizards. I have a Plain Jane Explorer with a pushrod type 4.0L, OHV, that has a leaky timing chain cover gasket. No big deal there but we cannot get the front crank pulley to come off or even budge. This pulley has two threaded holes in which to...
View
1996 Ford Pickup 4.9L No Start
This truck goes into a no-start condition after a hot soak or after it has cooled down for at least 4 hours.the truck fails to start sometimes for 30 seconds and then sometimes longer. I have a spark tester connected and the spark is extremely weak or missing ...
View
2002 Ford Explorer 4.6L right rear wheel
Customer came in with right wheel locked and brakes burned, replace right rear caliper and pads and brake hose, bleed system. car was all right for about a week. Came back with same problem customer saying brakes hot with wheel spinning free. showing signs of ...
View
2002 Ford Explorer 4.0L parking brake system
Does anybody have any idea on what could possibly be the next step to d&a, or have any idea of what could be the possible cuase? Any help/info would be great! THANKS!
View
2003 Ford Escape 3.0L Cuts out, Stall
Greetings, Customer's description of problem: While driving on the freeway she felt a jolt and the speedometer went down to zero, no power from the engine when stepping down on the gas. Engine stalled out. She pulled over, restarted engine and one minute later...
View
2005 Ford Thunderbird 3.9L timing chain
AFTER CAR AT REST FOR 10h RIGHT BANK CHAIN RATTLE FOR ABOUT 10 sec.NO MORE, WILL NOT DO IT AGAIN UNTIL NEXT DAY. I THINK IT THE UPPER CHAIN TENINSOR OR VCT CONTROL PROBLEM
View
2005 Ford Taurus 3.0L unknown
Hi everybody, i have a 2005 ford taurus in my bay. The customer states intermittently it will blow warm air when driving in low speed/high traffic situations on hot days, with high humidity. I instantly thought cooling fans. Low speed fan works fine. The high ...
View
2006 Ford Ranger 4.0L No Start
This one is really starting to screw with us. Truck was brought in on flat bed. No start and no crank. Security light flashing rapidly. Checked all fuses--ok. Attempted to communicate with PCM using IDS and no communication. Checked powers and grounds to PCM--... Trouble codes: P1639 (vid block), B1602 (pats system), B1213 (pats system).
View
1995 GMC Jimmy 4.3L firing
this is a nother gm nightmare not firing has not spark has power to the coil the modguel and crank sensor
View
1997 GMC Savana 4.3L Excessive Emissions, Poor Idle Quality, Cuts out, Stall, Misfire, MIL Lamp on
at start up runs rich both 02s over 1 volt and misses on cyl 1,3,5 injector pulse 3.o bank 1, 5.0 bank 2 engine light will then come on and go to open loop and smooth out checked ignition ok any help please
View
2003 GMC Yukon XL 5.3L Poor Idle Quality, Misfire, MIL Lamp on
vehicle was running ok.customer pulled out to pass a car and the check engine light started to flash,after passing the vehicle lost all power. i checked for codes and found a random misfire code,tested fuel psi it's 45psi i have many misfires on the left bank,... Trouble codes: PO300B (engine misfire).
View
2004 GMC Yukon XL 5.3L transfer case shift control
This is my own vehicle, but I am a brake and front end guy so I don't have much experience with type of problem. The service 4wd message came on and set a code c0327 (encoder circuit). When I went to live readings, the car would not communicate with the scanne...
View
2005 GMC Yukon 6.0L Unknown
2005 yukon denali whistle sound from vents with a/c on doesnt matter what the fan speed or the temp is set to. when the sound occurs it will only last for about 5 to ten seconds no real repair related history we replaced the a/c compressor and reciever dryer a...
View
2006 GMC Sierra 6.6L compressor
After repairs flushed/charged system, fired truck and no compressor function. Tested sensors as stated above, but still not receiving signal from PCM Also truck has manual type a/c system Any help appreciated -Eric
View
2003 Hyundai Sonata 2.4L Poor Idle Quality, Hesitation, Misfire
Car came in with broken t belt/ valves. We replaced the head ( reman. with cams/ lifters) and timing belt, it runs bad at idle miss fires heavily, a bit smoother off idle, idle vacuum is around 12 inches and goes to 15 inches at 2500 rpm. Compression seems hig...
View
1995 Jaguar XJS 4.0L feul guage
replaced bad sending unit.. was able to make gas gauge move by varying resistance through sending unit wires via blu point instrunent tester.. guage still didnt move... replaced slosh module after verifying wire to guage was good and resistance from sending un...
View
1999 Jaguar XK8 4.0L No Start
Thanks in advance for all your help. I am kinda stuck on this one as I do not get many Jaguar's in the shop but this car is a good customers of mine so I did not want to turn it away. Car came in as a no start. I have injector pulse but no signal to coils. I p...
View
2006 Jeep Commander 3.7L cruise control
Customer came in complaining that when the set button was pushed the cruise would accelerate to 85mph then jerk or surge. Test drove and verified problem. Scanned came up with code PO582, installed new cruise module. Now wont work at all. Cruise light on dash ...
View
1997 Kia Sephia 1.8L fuel
engine surge when pedal held at steady position don't no probelm check map sensor show good. no dtc code
View
2005 Kia Optima 2.4L No Start, Stall
The car was towed with a no start condition. If you worried with it a while it would start and run on two cylinders.(1 and 4) I scoped the control signal to the coils and tested the power and ground to the coils and all looked good. The waveform was identical ... Trouble codes: P0320 (ign failure sensor).
View
2003 Lexus GX 470 4.7L Vehicle Skid Control
I need some help from some Lexus/Toyota pros. I am a tech at a used car dealer. This Lexus came in for a slight steering wheel shimmy at 55-70mph. It is not constant and seems to change depending on road conditions. First we took it to a goodyear to have the t...
View
2005 Lexus RX 330 3.3L transfer case
is there any way to get transfer case out without pulling whole engine assy like alldata says
View
1999 Mazda 626 2.5L timing belt
engine timing jump after few days. posibly cold start. happens a third times
View
2001 Mazda 626 2.0L No Start
car came in as a no start,car will crank but no start. checked for spark and had none. checked for fuel, none. found the 30a fuse blown under hood for the egi/inj . replaced fuse , as soon as i hit the key to crank it blew fuse again. tried again but same resu...
View
1998 Mercedes-Benz C230 2.3L ac dash unit
Customer brought in his car complaning about a high pitch squeal coming from the dash ac controll unit. you do not hear the noise when the car is on and in park, but if you put the car in reverse the noise appears. if you turn the ac unit on the noise will go ...
View
2002 Mercedes-Benz C230 2.3L cooling fan
We have a problem with the cooling fan not wanting to turn on. The cooling fan is installed new, and the computer is replaced with a used one, but the numbers on it are the same. We're wondering if the used computer needs to be reprogrammed so that the car can...
View
1999 Mercury Villager 3.3L steering, suspension, ride control
There is a pretty harsh vibration when driving over 60mph. Stymptom is felt in the body of van and not necessarily in the steering wheel. This problem is really noticeable, yet hard find. I would hate to give it back to customer like this, any help will be muc...
View
2002 Mercury Sable 3.0L Cuts out
Customer brought vehicle in complaining of vehicle misses are cuts out if you are trying to pass someone on the highway. Test dreove vehicle it acts like rev. limiter is coming in to affect when you go into passing gear. If anyone has seen this please heklp th...
View
2004 Mercury Grand Marquis 4.6L Surge
Cruising at 50 mph this car surges after going into overdrive. Acts like downshifting or possibly in and out of overdrive. No codes. Fuel trims are normal. We replaced spark plugs and #7 & #8 coils because mode 6 data showed misfire counts on those cylinders. ...
View
2003 MINI Cooper 1.6L power steering
Simple question for you Mini Guru's. Got this Mini Cooper S and the power steering is not working. There is no battery power to the pump. Where is the 100 amp fuse that feeds full time power to the power steering? Mitchell shows it as FL4 in the under hood fus...
View
1997 Mitsubishi Galant 2.4L Power Windows
All 4 Power windows do not work All fuses and wiring were inspected and found to be OK. I have read some other posting that talk about the ETACS. Is the ETACS the problem? I have power at all for window swiches and I have checked the motors and they all work a...
View
1991 Nissan Maxima 3.0L alt wiring
Greetings, I received this vehicle with the alt wiring at the battery fuse link cut and the fuse link missing. I am trying to determine why someone would do this to make sure there isn't a short or something going on. Can anyone tell me what the current draw...
View
2000 Nissan Maxima 3.0L Hesitation, no power
MAXIMA CAME IN WITH EXTREME LACK OF POWER-ACTS LIKE PLUGGED CAT.DID A BACKPRESSURE TEST AND FOUND IF YOU INCREASE THROTTLE SLOWLY TO 3500RPM BACKPRESSURE STAYS BELOW 1 PSI.IF YOU FLOORBOARD IT IT WILL NOT ACCELERATE PAST ABOUT 2500/3000 RPM AND BACKPRESSURE IS...
View
2001 Nissan Pathfinder 3.5L No Start
Hi everyone, thank your time, After body work (front end),the car drived to my shop,with check engine light on, no gas padel feeling, only 10km /h less speed,check code P0100 mass air flow sensor,P1320 ignition signal,P1136 crank sensor, after check and tying ... Trouble codes: P0100 (mass air flow sensor), P1320 (ignition signal), P1136 (crank postion sensor).
View
2003 Nissan Altima 3.5L Misfire, loss of power
Hi Gang, I would like to say thanks in advance on this. This vehicle has a severe loss of power at higher engine RPM (4200 and up) with a pronounced engine spark knock. When it is colder it also has an induction backfire. O2 sensor voltage flat lines at 0V whe...
View

Fixes & Summaries for All Makes and Models
Fix/Summary Answers
2005 Audi A4 3.2L Steering angle sensor
Used the procedure from Rosstech wiki. Recalibration achieved and everyone happy. Thanks again to those who took time to help me. Best regards. Peter
8
1995 BMW 325is 2.5L Unknown
This BMW needs a alternator it was not charging, the car died out and this is how we discovered its issue it all makes sense now, we had no indication of a charging problem. Thanks for all input! Stewart
12
2000 BMW Z3 2.5L odometer
All replies indicated the need for a new cluster.The cluster is NLA from BMW.A freind at another shop knew of someone who repairs electronic speedos he said that the coding chip and the main chip in the cluster had lost communication due to the voltage spikes...
3
1988 Chevrolet llv mail 2.5L No Start
thanks to all who took time to reply.everything that was suggested we had tried already. what the fix seemed to be was when the engine was replaced the plug on the coolant sensor at the rear of the cylinder head was broken.it is a 2 pin sensor and the wire wa...
15
1992 Chevrolet Corvette 5.7L Poor Idle Quality, Surge
Thanks again guys. Walter, Phil and William were the winners. I ohmed the injectors cold and got 12.4 on all but #3 which was 9.8. I scoped it and had a shorted pattern with a kick down after turn off. Hot was the same reading on resistance. Replaced #3 and al... Trouble codes: 13 (left o2s or ckt), 45 (left o2s rich), 43 (ESC module or sens ckt).
11
1994 Chevrolet Pickup 6.5L Excessive Emissions, Poor Idle Quality, MIL Lamp on
I went ahead and pulled the timing cover off. This is a reman the cust. installed, with only 50 miles on it. I guess the reman company was short on timing chains! it looks like the chain was very well used, had so much slop I am surprised it didn't slip. repla... Trouble codes: 34 (stepper motor fault), 35 (injection pulse width error), 88 (tdc offset error), 91-98 (cyl balance faults).
6
2000 Chevrolet Monte Carlo 3.8L coolant fans
A used compressor had been installed on the vehicle in an attempt to stop the noise and the refrigerant leaked down to a level that would not allow the fans to come on with the AC turned on.
5
2002 Chevrolet Silverado 6.0L Poor Idle Quality, Misfire
thanks to all 8 replies.re-set the pcm w. factory programming. after customer called to say he had power programmer. and did crank re-learn. (labscoped fuel pump waveform ok. f/pressure ok.. did volumne test ok. the fuel sample was poor. added fresh fuel. rest...
8
2002 Chevrolet Malibu 3.1L Excessive Emissions, Poor Idle Quality, Cuts out, Stall
Thanks for all the help guys it turns out there was a ground bundle that was broke and making poor contact, it was actually making enough cotact to run, repaired the ground and made sure it had good connection Been driving it for 2 days and no problems. Anothe...
10
2005 Chevrolet Corvette 6.0L Starting
Thanks for the input guys. I went back out yesterday morning and looked over the data one more time. I checked every possible data list and still could not find a PID for "crank request". The vehicle still would not start. I disconnected the battery and touche...
4
2005 Chevrolet TrailBlazer 4.2L No Start
when I checked Ign.1 my scanner showed 10.9 volts so I knew my ign. switch was go started to dig around un wireing harrness to injectors and back behind head and firewall found 7 wires chewed into made necessarry repairs on harrness Blazer runs great THANKS Trouble codes: NONE (testing and results).
12
2006 Chevrolet Cobalt 2.2L Cuts out, Stall
Hello again, and thanks for the useful information, The ground under the headlamp appeared ok, but took it loose, cleaned it, and put it back together. Also I looked for the bulletin I was told about for injector contamination, could not find it. But I did com... Trouble codes: p0128 (coolant temphistory code), p0106 (mapbarohistory code), p0300 (misfirehistory code not current).
5
2000 Chrysler Concorde 3.2L Hesitation, Surge, Cuts out, Misfire, MIL Lamp on
hello again, sorry for the late reply. Despite the appearance of a good pattern,i took some of your advice and replaced the cam sensor. BINGO. I am sorry to say i cannot explain why this was the fix but thanks a lot for all your help. Trouble codes: p0355 (igniton primary circuit cylinder 5).
12
2006 Dodge Charger 5.7L Radiator
It seems there is no special tricks, just more trouble than most...BUT due to the body damage done, the insurance company preferred to tow the vehicle to a body shop to get all the work done at one time, not just the radiator replacement... so I didn't get to ...
3
1988 Ford Ranger 2.9L Low Power
Ok, I made this way more difficult than necessary. I was sure my low power problem was a lack of fuel or a plugged exhaust. As I wrote I ruled both of those out, so the next thought was echoed by many who replied that the ignition control or the PIP was at f...
29
2002 Ford Pickup 7.3L exhaust bolt plug
sorry to take so long this is our shop truck and is on the back burner. we apparently have a previous repair and are in process to make up a plug with a local machine shop. we ruined our plug trying to get the bolt out of it. thanks for the info and lock and s...
3
1997 Geo Tracker 1.6L Hesitation, Surge
Thank you for the help. Im glad I didnt buy a MAF. Three relpies were about the timing belt and gears It was a loose crank bolt. It wollered the keyway a little and wiped out the key itself,thank God for that.The pulley moved a lot so it was really retarding t...
6
2005 Infiniti FX35 3.5L No Start
thank you for all the replies we did not get to check much more on this car due to the coustomer being impatient so they sent a wrecker and took it to the dealer they have not sent back any info as to what was found if they do i will update the info. Trouble codes: P0451 (evap press sensor).
5
2004 Jaguar XJ8 4.2L MIL Lamp on
We updated the engine control unit as recommended for this issue and on the Evap issue we checked system and found a faulty gas cap. Thanks for the information! Stewart
2
2001 Mercury Villager 3.3L Poor Idle Quality
sorry for delay in closing,i was out of town for ten days,anyway the car was returned to customer with noise still there,the iac motor was determined to be the fix by way of iatn archives but it did not cure this one,replaced pcv also ,car runs really well so ...
4
2004 Mercury Monterey 4.2L mirrors, seat, pedals, backup sensors,
We found that all the circuits go to the drivers seat module. unplugged the module and plugged it back in and everything started working, customer did not want to go any further. Maybe its like windows ,you just need to reboot it. thanks to all!
3
1996 Pontiac Firebird 5.7L Poor Idle Quality, Hesitation
had to close due to time. still working on car. i beleive my fuel trim problem may be intake gasket issue. looks like somebody was in there once and one bolt was only started a few threads. smoked intake and was getting a little smoke from intake but could not... Trouble codes: p1810 (trans. press switch manifold fault), p1870 (trans. component slipping).
7
2001 Subaru Legacy 2.5L code p0778
we droped pan and repaired [...] wires due to pan pushed wires against valve body thanks for advice on checking grounds they were all good
1
1991 Toyota Pickup 3.0L No Start
turns out that this truck is flooding when cranked hot. the cold start injector is geting turned on by the comp. i disconected the cold start timer and it still shows signal i disconected it from comp and it stops. left comp wire cut and turn over to custome...
11
2004 Toyota 4Runner 4.0L abs-vsc light
THANKS TO ALL THAT RESPONDED TO MY POST. I CHECKED EVERYTHING I COULD WITH THE EQUIPTMENT I HAD. I ENDED UP SUGGESTING THAT THE OWNER TAKE IT TO A DEALER. HE SAID HE WOULD LET ME KNOW WHAT THE PROBLEM WAS. PS I COULD NEVER FIND A TONE RING ON EITHER REAR WHEEL...
4
2002 Volkswagen New Beetle 2.0L cooling fans
there were several things going on at the same time. one , the fuse in the box on top of the battery was corroded so I repaired that and put a new thermostat in as it wasn't opening until 200 degrees and put in a new fan module( changed this twice the firs...
24
Prev (Also Available: All, Asian, Chrysler, European, Ford, GM.) Next