Join Now
International Automotive Technicians Network
Prev Professional Automotive Repair Technical Discussions for April 19, 2008
International Automotive Technicians' Network (iATN) - Members Only
Next
(Also Available: All, Asian, Chrysler, European, Ford, GM.)
Vehicle Owners: If you are seeking an automotive repair professional to service your vehicle, visit the iATN Repair Shop Finder.

Open Help Requests for European
Help Request Answers
2002 Jaguar X-Type 3.0L cooling fan VIN: SAJEA51C72
Help, I only have a partial wiring diagram. Veh came in for overheated problem (towed in). Customer stated that it suddenly overheated (went to red and was shut off by customer. When it arrived at shop it started and ran fine. Filled with coolant and checked, ...
View
1982 Mercedes-Benz 240D 2.4L vacuum VIN: WDBA23A1CB
Need some info on vacuum system, to the injection pump and the transmission, the injection pump has 4 vacuum lines, back is engine kill, other 3 i do not know. Transmission has 1 line I would think this should have vacuum at idle and part throttle, and no vacu...
View
1995 Mercedes-Benz E320 3.2L seat belt motor VIN: WBD8667907
ok guys, this one has a very loud passenger side restraint motor, the drivers side also makes noise but not as much. every time the ignition is switched on it makes a grinding noise for about 5 seconds, also when the belt is buckled it cicles again.My question...
View
2003 Mercedes-Benz CLK430 4.3L serpetine drive belt VIN: WDBLK70G73
Thanks in advance for any help, the serpetine belt broke because the tensioner pulley froze up. Waiting on parts to complete this repair. The tensioner pulley was very easy to remove but the idler pulley m50 torx bolt will not clear the water pump hsg it hits ...
View
1991 Volvo 940 T 2.3L No Start VIN: YV1JA8747M
Car came in on a tow radio missing, wires cut. Fuse 11 no power. fuse 12 blown. I put another fuse in fuse 12 didn,t blow.I ran a fused jumper wire to fuse 11. Power to fuel pumps was restored without blowing fuses. Attempted to use diag connector, LED on stea...
View

Fixes & Summaries for European
Fix/Summary Answers
2001 Audi Allroad Quattro 2.7L ABS module VIN: WAUYP64B41
Friends, many thanks for your time and advise, especially to Mark "Jake" Jacobson, who described the coding procedure in detail and provided LOGIN and CODE, also after ABS module coding you have to adapt steering angle sensor. After successful LOGIN ,ABS modul...
7
2002 Audi A4 1.8L MIL Lamp on VIN: WAULC68E02
Hi all. Chalk this one up to a lack of familiarity with the WAY a VAG system responds to circuit conditions, lack of understanding of component identification due to lack of experience... And borderline ridiculous design theory thrown in there just for fun?... Trouble codes: P1530, 17700 (MAP controlled engine thermostat circuit open).
12
1993 BMW 325i 2.5L blower motor VIN: WBACB3324R
bad new resistor,hope this helps anyone second guessing meter readings
4
2003 BMW X5 3.0i 3.0L intake manifold VIN: 5UXFA53583
Thank you everyone for your assistance. I ran the engine with the belts disconnected - noise was the same. Removed DISA and the intake boot, throttle body, IAC - all parts in good condition. Cleaned and refitted all. Smoked intake - no leaks found. Compared w...
12
2003 BMW 325i 2.5L oil can lite VIN: WBAAZ33463
HI AND THANKS FOR THE HELP , A NEW LEVEL SENSOR AND ALL IS WELL. THIS SEEMS TO BE AN ISSUE WITH THESE CARS WE HAVE A FEW THAT ARE JUST LIVING WITH IT. THANKS AGAIN
18
2003 Land Rover Discovery SE 4.6L MIL Lamp on VIN: SALTY16473
Not sure if this is fixed yet, but I have at least isolated the problem(more or less). More extensive tested has revealed that the O2 sensor readings were dropping out intermittently due to a fault in the wiring between the O2 sensor and the CPU. I had previ... Trouble codes: P0150 (O2 Sensor Circuit Malfunction Bank 2 Sensor 1), P0174 (System too Lean Bank 2), P1174 (Pending Code System too lean Bank B).
7
Prev (Also Available: All, Asian, Chrysler, European, Ford, GM.) Next