Join Now
International Automotive Technicians Network
Prev Professional Automotive Repair Technical Discussions for April 9, 2008
International Automotive Technicians' Network (iATN) - Members Only
(Also Available: All, Asian, Chrysler, European, Ford, GM.)
Vehicle Owners: If you are seeking an automotive repair professional to service your vehicle, visit the iATN Repair Shop Finder.

Open Help Requests for Chrysler
Help Request Answers
1997 Chrysler Sebring JXi 2.5L Excessive Emissions, Poor Idle Quality, Misfire VIN: 3C3EL55HSV
this car came in with a missfire under load rep[laced cap rotor wires plugs now has missfire all the time costumer says it comes and goes replaced all injectors after cleaning multiple times tried blocking off egr both ends no change replaced distributor no ch...
2000 Chrysler Town & Country (Van) LXi 3.8L tcm VIN: 1C4GP54L9Y
hey guys this van has no communication with my modis and i have a no ccd message from tcm code p1698 check the ccd bus lines i have 2.2 volts and great coninuity to pcm and dlc. the tcm is not turning on the transmission control relay and i have no really good...
1991 Dodge Grand Caravan LE 3.3L Poor Idle Quality VIN: 1B4GK54RXM
When cold rolling idle, hot idle ok. We have check for vacuum leaks and dissambled and clean throttle body. Customer pissed off.
1998 Dodge Ram 1500 Truck 5.2L No Start VIN: 3B7HF13YIW
Hello every one here we have another one customer says he had some one looked at it they told him he misfire on 2 of the cylinders and he replaced cap,rotor,wires,plugs,air filter after that no start conditions happened he had some looked at it to verify firin...
1998 Dodge Dakota 5.2L freeze plug
does any one have easier method of changing the freeze plug located behind the motor mount on the rh side of engine block?any help would be greatly appreaciated,thanks
2002 Dodge Stratus SE 3.0L 3-4 shift VIN: 4B3AG42H72
lets start by saying thanks to anyone can help car came in trans slips in all gears fluid burned up sent trans out to rebuild came back with slight slip going into 4 th tried another unit did exact same thing have tried all solenoids still same car has after m...
2002 Dodge Caravan SE 3.3L Limp Mode VIN: 1B4GP25362
Im stuck in limp with code 725 (Speed sensor prob) which will return during a test drive after being canceled. During that short window, trans shifts normal. I did wire in new pigtails to both speed sensors, to no avail. My scanner shows RPM's on both input an...
2003 Dodge Dakota Sport 4.7L check gauge light on VIN: 1D7HG38N13
truck came in for full service and has CHECK GAUGES light on, all gauges read normal, cust stated that the alt gauge seems to be a little bit higher than before. charging test show 13.3 at idle with a analog gauge you can see the needle fluctuate a bit when th...
1998 Jeep Cherokee Classic 4.0L Poor Idle Quality, MIL Lamp on VIN: 1J4FJ68SXW
Thank You in advance After ecm replacement data and stored codes could be retained Now after vehicle sits for about 45 mins. if it is test driven after 1 block will hesitate and pop once [about 2 sec.] through air cleaner box then run perfectly until vehicle s... Trouble codes: P0138 (1/2 o2 voltage high)
1999 Plymouth Grand Voyager 3.0L pcm VIN: 2G4GP2439X
The van has a faulty bcm causing lighting problems but that is not my question,I installed a used bcm that did not work and caused eratic electrical system operation including theft light flashing but the van does not have theft (black key),now after re instal...

Fixes & Summaries for Chrysler
Fix/Summary Answers
1995 Chrysler Concorde 3.5L timing belt VIN: 2C3HD56F1S
Thank you to all that took the time to reply, after further investigation the problem was that the dealer sent us the wrong water pump, the pulley on the old pump was about twice the size in diameter, When the dealer originally and the second time he looked up...
2003 Chrysler PT Cruiser GT 2.4L power steering VIN: 3C8FY78G93
Thanks to everyone who took time to reply. It was the pump as most suggested. Just wanted to confirm my thoughts before ordering a 400.00 pump from the dealer.
2003 Chrysler Town & Country (Van) LXi 3.8L tire pressure monitor VIN: 2C4GP54L33
Thanks for the replies Gilbert,Steve,Paul and Ryan, although this vehicle/problem didn't get fixed by our shop i did recommend the customer take it to a dealer and see if anything is read by a factory DBR tool which was suggested that a factory tool may pull a...
1989 Dodge D250 5.9L No Start VIN: 1B6KE682KS
Thanks for all of the replies. I found that the wires for the fuel shut off solenoid were somehow reversed. Put in proper place and now truck starts normally. Don't know much about this system but it starts first time every time now.
2001 Dodge Durango SLT 4.7L headlights VIN: 1B4HS28N11
I just want to say thanks to all that replied. This was my first help request and am very happy I did. Thanks to Kevin from Manitoba and Arturas from Florida. It turned out to be the central timer module located in the left kick panel. Probably nothing to ...
2003 Dodge Ram 1500 Truck 4.7L rear differential VIN: 1D7KU18NX3
Thanks to all that responded. Even though backlash was set properly and the ring and pinion gears showed no damage or wear, we had reached a dead end so out of pure frustration we replaced them anyway and the noise disappeared. All bearings and races were in p...
2004 Dodge Stratus SE 2.7L timing VIN: 1B3EL36T84
Thanks for all the help. After hearing from you guys and double checking everything, I felt much more confident starting a car that was making that much noise. After about 15 sec of cranking the car started and made alot of noise for about 2 or 3 more second...
2004 Dodge Intrepid SE 2.7L Rear Struts VIN: 2B3HD46R84
First off, thanks to everyone who took the time to reply. Rather than drilling out the bolts I decided to remove the strut with the spindle attached. I removed the calliper, rotor, hub and backing plate (left sensor & brake cable attached and held to the side ...
2003 Jeep Wrangler SE 2.4L engine VIN: 1J4FA29173
Hi all It was the no 3 rod bearing ,found it buy removeing plug wire and rattle went away ,this was not a normal rod noise I thought it woult be higher up in the engine .I started removeing the pan and saw some metal in pan had play on no 3 remove and found s...
Prev (Also Available: All, Asian, Chrysler, European, Ford, GM.) Next