 Prev |
Professional Automotive Repair Technical Discussions for November 7, 2007 International Automotive Technicians' Network (iATN) - Members Only |
Next  |
| (Also Available: All, Asian, Chrysler, European, Ford, GM.) | ||
| Vehicle Owners: If you are seeking an automotive repair professional to service your vehicle, visit the iATN Repair Shop Finder. | ||
Open Help Requests for Chrysler
| Help Request | Answers | |
| 1990 Dodge Grand Caravan LE 3.3L i/p Owner dosen't have the owners manual. Am unfamiliar with the reset procedure for the "main't req" light. All-data is down and don't have a hard copy manual (don't think in ten years I've ever reset a oil life monitor on a 1990 Chrysler). |
View | |
| 2001 Dodge Stratus SE 2.4L Poor Idle Quality, MIL Lamp on VIN: 1B3EJ46X51 after replacing sensors and clearing codes, sensors work ok for less than a minute than slowly voltage rising above 0.5v and stays above all the time, st adap drop to -24%, and car runs at low rpm like it was going to die. after few minutes it desables sensors... Trouble codes: P0132 (1/1 o2 sensor shorted to voltage) |
View | |
| 2003 Dodge Grand Caravan SE 3.3L MIL Lamp on VIN: 1D4GP24393 Mil has come on with code P0601, Memory error. I will admit, the info I have read on this code has not empowered me about what to do with it next. Emmision warranty expired 2000mi. ago, most things point to PCM. Any experience on this code and advice is greatl... Trouble codes: P0601 |
View | |
| 2004 Dodge Intrepid SE 2.7L rotors VIN: 2B3HD46R64 We have a 04 dodge intrepid with 56k miles.The owner was complaing of his steering wheel shaking at 60mph when brakes are applied as speed decreases the shake seems to go away.This not a very violent shake or woble in the steering wheel., We repaced with new r... |
View | |
| 2002 Jeep Wrangler SE 2.5L Gauge VIN: 1J4FA29P62 I have this Jeep here that the oil pressure gauge is acting up, when it first orginally came in the oil gauge was showing no oil pressure, pressure was checked and was good, cold aound 50 to 60, hot around 25 to 35 or better, then I check the signals in and ou... |
View |
Fixes & Summaries for Chrysler
| Fix/Summary | Answers | |
| 1994 Dodge Intrepid ES 3.5L No Start, Stall VIN: 2B3ED56F1R thanks to all who responded, most responses said to check ground, mechanical timing and wiring issues behind egr tube. the tech rechecked everything and found some wires rubbed through and part of the harness clamped between the engine and trans where someon... |
13 | |
| 1998 Dodge B3500 5.9L speedo VIN: 2B6LB31ZXW Sorry for the delay in posting the fix, there was a delay in getting the reman pcm from chrysler. We installed the reman pcm and it seems well at this time. Thanks for all the help - IATN is a great tool to have! |
4 | |
| 2000 Dodge Neon High Line 2.0L Starting Well, I got the no start condition to act up once, when I had the key in the crank position,it didn't crank over, I moved the shifter from park to reverse and I could hear the starter relay click. I put the car back into park and the click happened again. I to... |
4 | |
| 2004 Dodge Stratus SXT 2.4L Stall VIN: 1B3EL46XX4 I want to thank those who sent me replies to my problem. I'm still new to this site and am learning more about posting information. I did a fuel pressure test and had 58 psi. I tried to monitor the fuel trim but the data stream numbers were very erratic. the n... |
8 | |
| 1993 Jeep Grand Cherokee 4.0L No Start VIN: J4GZB8SXPC thanx to all most said use dealer coil seems to be the fix Seem to be a resistor built in the oe one. |
4 | |
| 1994 Jeep Cherokee SE 4.0L Unknown VIN: 1J4FT27S1R Well, just about everyone said bearings, someone just commented "pinion bearing", well that was it. It was so pitted I could not believe it. replaced all bearings and all is well. thanks to everyone, sorry to bother you guys with such a silly question. |
15 | |
| 1989 Plymouth Horizon America 2.2L heater core VIN: 1P3BL18DXK Thanks for all the information. Something I learned from this job besides what I asked is to be very careful in accepting such jobs when the car is this old. The job was MUCH harder because the plastic parts were so brittle! It was necessary to remove the da... |
6 |
