 Prev |
Professional Automotive Repair Technical Discussions for May 23, 2007 International Automotive Technicians' Network (iATN) - Members Only |
Next  |
| (Also Available: All, Asian, Chrysler, European, Ford, GM.) | ||
| Vehicle Owners: If you are seeking an automotive repair professional to service your vehicle, visit the iATN Repair Shop Finder. | ||
Open Help Requests for Chrysler
| Help Request | Answers | |
| 1990 Chrysler New Yorker Fifth Avenue 3.3L No Start, Poor Idle Quality, Cuts out, Stall VIN: 1C3XY66R8L Hi Tech, It must be my good week. This new yorker came in from another shop with a no star. Upon preliminary checks i found no cam signal, now it has a new cam sensor y i have cam and crank signal,When cranking, the car will start for a split second and shut d... |
View | |
| 2000 Chrysler Town & Country LX 3.3L Hood VIN: 1C4GP44GXY Hello to all. Looking for some help from the body repair people or anyone who knows how to open a hood on this van. Cable inside seem to be broken mid streem somewhere. Dealer wants 4 hours minimum to start. Trying to help out a good customer. Any ideas? |
View | |
| 2004 Chrysler Pacifica 3.5L drain-dash VIN: 2C8GF68434 Hi there, battery drained, once charged found thedash lamps-trac control-seat belt-abs-red brake warning lamp-tire pree moniter-engine lamp-gauges lit-gear selector, all on and draining battery. appears that moving key around may make/break some connection. ho... |
View | |
| 1996 Dodge Intrepid 3.3L Cuts out, MIL Lamp on VIN: 1B3HD46T2T After driving this for 1 1/2 to 2 miles it will cut out,jerk,pop through the intake and exhaust. After about 2 miles it will stop acting up and and will fine again until the next day.Sets code p1391. We have replaced the cam and crank sensor with Carquest, re... Trouble codes: P1391 |
View | |
| 1996 Dodge Caravan 3.0L brakes VIN: 2B4FP2535T Hello, I have a caravan that had a low spongy pedal,we bled the brakes and found air in the front,especially the left side. After beeding the pedal came up and felt fine. After a couple of weeks it returned with same problem. This has occured several times and... |
View | |
| 1997 Dodge B2500 3.9L Cuts out, Misfire, MIL Lamp on VIN: 2B7HB21X3V Van originally came in with a low charging voltage & misfire # 4 cylinder code with a complaint of no power. Scoped the ignition & found a bad plug wire to number 4. Replaced the set with a new cap & rotor. Looked good on the scope & test drove fine. No codes ... Trouble codes: P1391 (Intermittent Loss Of Cam or Crank Signal), P0300 (Multiple Misfire), P0301 (Misfire 1 Cylinder), P0302 (Misfire 2 Ctlinder), P0304 (Misfire 3 Cylinder), 47 (Charging System Voltage Low) |
View | |
| 1999 Dodge Dakota 3.9L Stall VIN: 1B7GL26X7X Hello fellow techs, I would appreciate any input on this problem. Upon deceleration this Dakota will sometimes stall & sometimes not. While watching the scan tool data on "desired IAC" & "actual IAC", the counts stay together all the way to "0"! Desired idle R... |
View | |
| 2001 Dodge Dakota SLT 3.9L No Start VIN: 1B7GL2AX21 Hello guys and thanks in advance, this truck come for non start condition; no fuel pressure no power to injectors no communication with scanner and odometer flashes twice then display NO BUS, Checked power to pins #2 (lt grn/blk wire) and #22 (red/white wire) ... |
View | |
| 2003 Dodge Intrepid ES 3.5L shift mechanism VIN: 283HD56G03 Hello Fellow Techs, I am trying to install a solenoid pack (which is now on the inside of the trans). Small-data has a tsb on it and it falls into the date code catagory that it should be changed.The info to remove the valve body to change the solenoid pack wa... |
View | |
| 2004 Dodge Ram 1500 ST 5.7L parking lights VIN: 1D7HU18D24 Good morning Dodge techs,I have a strange one here.The parking lamps turn on by themselves.Checked for codes,park lamp relay output circuit open.I have both powers that come from fuse 15 to terminals 30 and 86,the problem is that when it is acting up is that I... |
View |
Fixes & Summaries for Chrysler
| Fix/Summary | Answers | |
| 1996 Chrysler Town & Country LXi 3.8L No Start VIN: 1C4GP64LXT thanks to all who helped , turns out coil shorted or caused the computer to crap out. but a new computer and coil took car of the problem. thanks again |
14 | |
| 2001 Chrysler 300M 3.5L Charge light/traction light VIN: 2C3AE66G01 Thanks all for the help.Here goes, After checking the wiring for the 4th time. I found that the NEGATIVE cable,battery connector was tight, BUT NOT MAKING CONSTANT CONNECTION. I had looked at this connection 3 times before. New( new battery had been installed ... |
5 | |
| 2005 Chrysler crossfire 3.2L MIL Lamp on VIN: 1C3AN65L15 Thanks to you guys that offered advice.I feel kind of stupid- while plugging/unplugging o2's to compare readings, I noticed that the scanner was showing 2/1 on the left bank and 2/2 on the right bank. The left side is the actual 2nd bank. Both wiring plugs com... Trouble codes: P0133, P0153, P0137. |
3 | |
| 2001 Dodge Ram 1500 Laramie 5.9L Hesitation, Cuts out Intermitten hesitation was the O2 sensor. Lack of power, coolant loss, and oil consumption caused from leaking intake gasket and leaking intake floor gasket. Had a lot or replies to this one. A lot of them pointing to the leaking intake floor gasket. A tell-... |
19 | |
| 2002 Dodge Ram 1500 SLT 4.7L engine VIN: 1D7HA16NX2 thanks for everybodys input, the problem turned out to be the plastic chain guide cracked. The lesson I learned on this job is if I get another 4.7 with chain noise change all tensioners and guides. thanks again. |
4 | |
| 2004 Jeep Grand Cherokee Laredo 4.0L 1-2 shift VIN: 1J4GW48S74 You guys are the best. I replaced the governor pressure sensor and scanner pressure showed 0 psi at idle and went up as you drive. Shifted through all the gears like butter. Once again thanks for all the speedy responces. Eric |
11 | |
| 2004 Jeep Grand Cherokee Laredo 4.0L Unknown VIN: 1J4GW48S34 this thing is fixed. thanks to all who replied. you guys were right. it was tight, but manageable. actually, it was pretty straight forward. timed the ring gear to the pinion before removal and got it out by using a large punch and my air chisel on the other e... |
4 |
