 Prev |
Professional Automotive Repair Technical Discussions for March 31, 2005 International Automotive Technicians' Network (iATN) - Members Only |
Next  |
| (Also Available: All, Asian, Chrysler, European, Ford, GM.) | ||
| Vehicle Owners: If you are seeking an automotive repair professional to service your vehicle, visit the iATN Repair Shop Finder. | ||
Open Help Requests for Chrysler
| Help Request | Answers | |
| 2000 Chrysler Grand Voyager SE 3.3L Ext crank, fuel odor VIN: 1C4GJ44G4Y After sitting for approx. 3 hours, van cranks for about 45 seconds before starting. Then, STRONG smell of raw gas comes out the A/C vents for about a minute. After that, all if fine, no problems whatsoever until the next time it sits. Underhood, gas smell is s... |
View | |
| 1993 Dodge Dakota 5.2L Excessive Emissions VIN: 1B76L23Y3P hi inta menbers. i need alittle help. i have a dodge dakota w/ high nox.at 15 mph. this truck has a new cat and egr. and still can't get nox down.i try injector claner and a new fuel filter,(filter was plugged) replace plugs no change.thinking running too lean... |
View | |
| 1996 Dodge Avenger 2.0L No Start VIN: 4B3AU42Y5T Car will not start. Using snap on Modis,I can read rpm's and it shows to have a cam and crank signal when cranking. I can pulse all the injectors and both sides of the coil pack with the modis. When I crank it , # 1 injector pulses once ,# 2 injector pulses co... |
View | |
| 2001 Dodge Ram 1500 Van 5.2L Hesitation, Misfire, MIL Lamp on VIN: 1B7HC13Y71 Started out with what seem to be a simple tune up. Came in with complaint of check engine light and engine miss. Scanned computer and found code PO304 cylinder #4 misfire detected. With the low mileage I just pull the plugs to check them. regular plugs so repl... Trouble codes: P0304 |
View | |
| 1993 Jeep Grand Cherokee Limited 5.2L Excessive Emissions, Poor Idle Quality, Hesitation, Surge, Cuts out, Stall, Misfire, Poor Fuel Economy VIN: 1J4GZ78Y5P when vehicle goes into closed loop,engine starts to run full rich,stalls at stop,very difficult to accelerrate and bucks misfires.have checked dist.for excessive gear lash,replaced map sensor,tps,o2 sensor,ignition pick up coil,have thoroughly inspected all gr... |
View | |
| 1997 Plymouth Grand Voyager SE 3.3L Stall VIN: 2P4GP44R5V This Voyager has a very intermittent stall when coming to a stop. It will always restart immediately. It happens about once every two to three weeks. I've never had it happen for me and there are no codes stored. I removed the throttle body and throughly clean... |
View |
Fixes & Summaries for Chrysler
| Fix/Summary | Answers | |
| 1997 Chrysler LHS 3.5L Misfire, MIL Lamp on VIN: 2C3HC56F3V I thank everyone very much, almost every reply said intake gaskets and wow got 42 replies, the most i ever seen . Sure enough it was intake gaskets blowed at #5 under intake manifold. As many replies I got this must be a common problem. You people kept me from... |
42 | |
| 1998 Chrysler Cirrus LXi 2.5L poor acceleration VIN: 1C3EJ56H7W Well Duane from Alaska was correct the fly wheel had broke and slipped about one inch.No symptoms from it,no vibration,no noise.Thanks everyboby for replying and offering your time and help...Carl |
12 | |
| 1983 Dodge Omni 1.6L bracket VIN: 1B3B218A2D Thanks to Bill [...] (Newport News, VA) for sending info and pictures of the part in question. Had a fine used specimen in stock. Boxed up, and shipped w/in a couple days. This jewel is now back in service. Was only searching for about a month before posting a ... |
4 | |
| 2001 Dodge Grand Caravan Sport 3.3L Left front brakes VIN: 2B8GP44R11 We went thru the elimination process just like most of the replies we received, and just as we expected the consensus was that it was an internal problem with the hydraulic control unit. We were looking for this confirmation before changing the control unit on... |
12 | |
| 1998 Plymouth Neon High Line 2.0L Poor Idle Quality, MIL Lamp on VIN: 1P3ES47Y9W Many thanks to all who posted replies. The problem was a bad map sensor. I replaced it and the car ran fine. Alldata text did not say that with the sensor unplugged scan tool would read 5 volts that I could find. Again many thanks to all who replied Trouble codes: P0108. |
8 |
