|Prev||Professional Automotive Repair Technical Discussions for September 17, 2004
International Automotive Technicians' Network (iATN) - Members Only
|(Also Available: All, Asian, Chrysler, European, Ford, GM.)|
|Vehicle Owners: If you are seeking an automotive repair professional to service your vehicle, visit the iATN Repair Shop Finder.|
Open Help Requests for Chrysler
|1996 Dodge B1500 5.2L Excessive Emissions, MIL Lamp on VIN: 2B4HB15Y7K
Need some help with this dodge van please? It has a p0171 code. Check fuel pressure, check for internal vacuum leaks like the intake problems that i read in the fix data base. Key on engine off the o2 reads 4.82 volts. Is this a feed back from a referance feed... Trouble codes: P0171 (lean o2)
|2000 Dodge Ram 3500 Van 5.9L Misfire VIN: 2B5WB35Z8Y
as seen in the repair history we have covered all the basics. at this point i am at a loss. Trouble codes: P0300, P0305, P0308
|1996 Eagle Vision TSi 3.5L power door locks VIN: 2E3HD66FXT
heeeeelp!!! power door locks don't work at all. tried both switches. snap on scanner connected shows roughly 2 volt and 6 volts when switches are toggled. if you supply voltage to output control at body computer all door locks lock and unlock. car also has oem...
|1998 Jeep Grand Cherokee Laredo 4.0L Hesitation VIN: 1J4GZ48S6W
this truck will back fire thru intake manifold when on accel from stop sign cold,has good fuel pressure,everything on scanner looks ok,once it warms up it will run fine,.thought maybe engine coolant sensor but no one has one on hand,thanks for the help
|1994 Plymouth Acclaim 3.0L Hesitation, Surge, Stall, hard start VIN: 1P3AA4633R
This vehicle has a problem. it was towed in for stalling and not restarting. when we got it in it had thick yellow spark,fuel and inj. pulse. we tried a coil, computer and a map sensor. vehicle all of a sudden started. now it starts hard, misses under loadand ...
Fixes & Summaries for Chrysler
|1996 Chrysler Sebring JX 2.5L Hesitation, Stumbles 45% of time VIN: 3C3EL45H3T
Between fixing the cam timing (new belt) & making reliable, consistent sparks with not the 2nd distributor, but the THIRD distributor, the engine now runs perfectly, (like what took you so long?). Apparently we should all have such an understanding part suppli...
|1991 Dodge B250 3.9L No Start, Hesitation, Stall VIN: 2B7HB21X5M
Customer picked up the van and said his buddy at the salvage yard could order one in. Called me yesterday that it had started just fine, but after a few minutes smoked out from under dash and died. Will not turn over now.Most replies were to check injectors, r...
|1999 Dodge Ram 1500 Truck 5.2L Dust seal VIN: 3B7HF13Z1X
Thanks to all who posted. Some of you even posted part numbers. Unfortunately these numbers were for the inner grease seals. Not the dust seals. A few dealership guys told me of a TSB to remove these seals because the caused a squeek and are no longer servicea...
|1999 Dodge Dakota 3.9L No Start VIN: 1B7GL22X9X
Hi Everyone, I appreciate all of the replys that I received but this vehicle was from left field.. The delay was in the dealer waiting to make up their mind what they wanted to do. First let me thank Dan [...],Adam (Hitch King),Richard ...
|2000 Jeep Grand Cherokee Limited 4.7L Alarm VIN: 1J4GW58N8Y
Thanks for all the replies, they were all helpful in understanding a little more about the system. I tested everything I could think of, including removing the rear hatch panel to access the connector to see if there was any damage to wiring for the glass swit...
|2001 Jeep Wrangler Sahara 4.0L Cooling Systems VIN: 1J4FA59SX1
thanks to all that replyed. We found no signs of coolant in the oil or cyl head oil galley area. We drove the vehicle for 5 days with little or no coolant lose. We will be monitoring the vehicle weekly. Thanks again.
|1994 Plymouth Acclaim 3.0L motor VIN: 1P3AA4636R
replaced seal again with oem seal so far so good . pcv system ok . thanks for the help i hope to never speak of this car again forthis problem
|2001 Plymouth Neon High Line 2.0L engine VIN: 1P3ES46C71
following the advice of peter from colorado,kent from florida, and h. steven from new york, i removed the rocker shafts to check the cam shaft lift. the lift was exactly what it was supposed to be. the only discrepencies in any of my test results was the 30psi...