|Prev||Professional Automotive Repair Technical Discussions for September 16, 2004
International Automotive Technicians' Network (iATN) - Members Only
|(Also Available: All, Asian, Chrysler, European, Ford, GM.)|
|Vehicle Owners: If you are seeking an automotive repair professional to service your vehicle, visit the iATN Repair Shop Finder.|
Open Help Requests for Chrysler
|1998 Chrysler Sebring JXi 2.5L when cranking VIN: 3C3EL55H8W
This car came from a used car lot they changed all parts listed above before it came to me. This is what I was told when they first got car they did not have correct key it would start and run with there key but would die after about 5 sec. They took car to de...
|1991 Dodge Stealth ES 3.0L Stall, Misfire VIN: JB3XD54B2M
Very Intermittently this car will miss on two cylinders when started cold. After a short while the miss is gone. When it is missing I have noticed no spark on the coil for 1&4. The primary signal to it also seems poor which I have checked right at the power tr... Trouble codes: 44 (Coil 14 circuit problem)
|1992 Dodge W250 5.9L flex plate VIN: 3B7KM23C1N
ck crankshaft endplay has .010 spec.is .004-.017.trans is r/b unknown milage
|1993 Eagle Vision ESi 3.3L Fuse link VIN: 2E3ED56T5P
The owner had replaced his own Alternator and still had a no charge condition. After inspection we found that the 12ga black fuse link below the battery box had melted. This we will have to order for the Dealer I guess. In the mean time we stuck a inline fuse ...
Fixes & Summaries for Chrysler
|1998 Chrysler Town & Country (Van) LXi 3.8L limp in VIN: 1C4GP64L5W
A big THANK YOU to all who sent help on this one! The responses were-several stating circuit board in cluster,pressing both buttons on cluster to get codes,voltage or ground drops on battery terminals,ignition feed for tcm,and the one who nailed it directly wa...
|1991 Dodge B250 5.2L No Start, Stall VIN: 2B7HB21Y1M
Hi, Sorry for the delay on the fix post for this one. The Dodge dealer warranteed the Sbec, and before I plugged it in, I disconnected all the input sensors, thinking I had one that was pulling down the 5 volt reference signal. I also unplugged the purge, EGR ...
|1999 Dodge Ram 1500 Van 5.2L rt axle seal VIN: 1B7HF13Y8X
Well we had some useful replies but no help-vent tube was clear-axle shaft ok-I ended up refunding the guy the amount recharged to replace it.He took it the local dealer who installed another seal-they did not see any reason for it to leak-The owner will let m...
|1999 Dodge Durango SLT 5.9L overdrive and lockup VIN: 1B4HS28Z4X
The TPS fixed the problem. Thank you to all who advised this repair, and sent us in the right direction.
|1995 Jeep Grand Cherokee Laredo 4.0L No Start VIN: 1J4GZ58535
First off I want to thank all that replied for your help. Thank you. In one way or a nother you all were corect, But I feel like I need to clarafie some things in case someone else experinces this same problem. using mitchell repair info for code 11 No crank r... Trouble codes: 11 (no crank refference).
|2002 Jeep Wrangler Sport 4.0L MIL Lamp on VIN: IJ4FA49SX2
Thanks to all who responded. All suggestions were valid: Les [...] suggested I was on the right track w/fuel pump module seal, Hyperflyer suggested I check the large hose going from charcoal cannister to LDP and also to check gas cap (already had been replace... Trouble codes: P0455.
|1990 Plymouth Grand Voyager SE 3.3L Misfire VIN: 1P4FH44R5L
i replaced the cam sensor after testing the crap out of it out of desperation and that gave me injector pulse at the #4 injector. truck runs smooth now but still runs like its to lean. once in a while it will backfire out the intake and accelerate sluggish. on...