|Prev||Professional Automotive Repair Technical Discussions for July 25, 2004
International Automotive Technicians' Network (iATN) - Members Only
|(Also Available: All, Asian, Chrysler, European, Ford, GM.)|
|Vehicle Owners: If you are seeking an automotive repair professional to service your vehicle, visit the iATN Repair Shop Finder.|
Open Help Requests for European
|2000 Mercedes-Benz E320 3.2L Misfire, MIL Lamp on VIN: WDBJF65J7Y
hi. I have a real trouble on this car. check engine light on p304.305,306. Only left side of bank. after change spark plugs and clear code. no problem at idle. test drive it. No misfire when drive gentle but step on the gas and accelate the car, check engine l... Trouble codes: P0304, P0305, P0306
|1966 Porsche 911 2.7L cam timing VIN: 3473211560
car came in with popping out exhaust. took compression test and found #3 cyl low 50lbs. all others 140lbs. Checked for tight valve #3 and found valves adjusted correctly. Removed engine and tore down top end. Ended up getting 3 used good heads and had valve jo...
|1994 Volkswagen Passat 1.9L Radio VIN: WVWZZZ3AZR
I had disconnected the battery to repair some wiringconnetions and the vihicle is ecept whit a codeprotected radio.The owner of the car can't refind his codenumber. Radio specifications : BLAUPUNKT CC 22 BP [...] 1992 [...] Is it possible to ref...
Fixes & Summaries for European
|2001 BMW 740i 4.4L MIL Lamp on VIN: VBAGG83441
Hello BMW Techs The throttle must be reset and the procedure is to clear all the fault codes and it will reset, in addition you must clear the adaptions with a scanner. The scanner readings of -6 for the additive mixture and +5 for the multiplicative and also ... Trouble codes: 114 (signal camshaft position sensor), 028 (additive mixture adaption bank 1 control limit reached), 029 (additive mixture adaption bank 2 control limit reached), 140 (activation map cooling), 021 (oxygen sensor ageing before cat. converter bank 2), 059 (transmission stall speed).
|2001 Land Rover Range Rover SE 4.6L rear axle VIN: SALPL16421
I received 3 responses to the problem. They all described a TSB that Alldata didn't have. The TSB said the cause was slack in the splines of the rear axle hubs & pinion flange. The fix is to disassemble the hubs from the axles, and the pinion flange from the s...
|1992 Mercedes-Benz 300D 2.5 2.5L Timing Chain/Cyl Head VIN: WDBEB28E0N
Success, due more to the help of people on this network than anything I did. The timing cover had to come off to change the upper chain guide. It anchors on a little pin at the bottom that's fastened into the block. Once I got the cover off, I was glad I did. ...
|1985 Porsche 944 2.5L Fit & Finish VIN: WPOAA094FN
The retrofit kit # p944-564-00 is the correct kit( to my knowledge)for this vehicle. The repair info for this retrofit is not. First off remove the existing brackets for the L & R transmissions( the bottom of this bracket is spot welded and must be removed at ...
|2000 Volkswagen Jetta 2.8L Misfire, CYL # 5 MIFIRE CODE VIN: 3VWSE29M9M
thanks to all for your time..i got some info from david in hemet,who is one who is there to help..he said to try switching wires and see if the miss changed, i saw the change in scanner to # 4 cyl..i got an old good wire and replaced it..miss gone..guess even ...