 Prev |
Professional Automotive Repair Technical Discussions for December 7, 2019 International Automotive Technicians' Network (iATN) - Members Only |
Next  |
| (Also Available: All, Asian, Chrysler, European, Ford, GM.) | ||
| Vehicle Owners: If you are seeking an automotive repair professional to service your vehicle, visit the iATN Repair Shop Finder. | ||
Open Help Requests for All Makes and Models
| Help Request | Answers | |
| 2006 Acura TL 3.2L B codes VIN: 19UUA66256 HI ALL,SO I REPLACED THE TRANS IN THIS CAR with an h & a reman unit.all was good for a few months.the guy then called and said he goes down a big hill by his house,and trans will downshift to 2nd and stay there till he stops the car,then continues on as no... Trouble codes: B1007 (Micu lost comm w/headlight switch), B1008 (Micu lost comm w/ guage module a/t message), B1010 (Micu lost comm w/ door multiplex cu), B1006 (Same as b1010), B1005 (Micu lost comm w/relay control unit), B1011 (Micu lost comm with guage control module) |
View | |
| 2015 Ford F-150 XLT 5.0L Loss can comm. VIN: 1FTEW1EF6F This vehicle was deer damaged and deployed all airbags, but was a very light hit to the front with no damage to the front bumper or radiator support. This vehicle came from a body shop, to have the RCM module programmed.When trying to program RCM found tha... Trouble codes: U4018, U1210, U1510, U2120, U4298 |
View | |
| 2009 Mercedes-Benz ML320 Bluetec 4Matic 3.0L OM642 diesel engine VIN: 4JGBB25EX9 Dear diesel mechanics, we would appreciate if some of you who are experienced with Mercedes/ Sprinter/Jeep diesel OM642 engines can give us their opinion. We would be especially grateful if someone who has attempted to rebuild an OM642 engine can offer adv... |
View | |
| 2013 Mercedes-Benz GLK350 3.5L front propeller shaft VIN: WDCGG8JB2D hi guys, after a bit of wrestling with the installation of the new propeller shaft due to a broken joint on the old one i decided to reach out. videos on youtube show guys doing this job on jack stands w/o removing the exhaust. well i have it on the rack a... |
View | |
| 2003 Subaru Outback 2.5L MIL Lamp on VIN: 4S3BH67513 Hello. I working on this 2003 Outback 2.5 motor. Code P0400 keeps coming back. I cleaned the ports then I replaced the EGR valve and checked that no broken wires or unplugged connectors. There is a self test connector under the dash (green) that I plugged ... Trouble codes: P0400 (No EGR flow) |
View | |
| 1984 Toyota Pickup DLX 2.4L Hesitation, Cuts out VIN: JT4RN65D1E This one has been a problem child for me, Head had been off previously and poor installation causing warped head. After installing head and adjusted valves it runs good at idle but when accelerating the timing would go negative. Found bad vacuum diaphragm.... |
View |
Fixes & Summaries for All Makes and Models
| Fix/Summary | Answers | |
| 2005 Cadillac SRX 3.6L No Start VIN: 1GYEE63785 First I want to thank all that responded. I repaired this vehicle with a Dealer replacement ECM. The unit I received was a reman unit and when the dealer was asked we were told that is all that is available. I bought a subscription from A/C Delco SPS and progr... Trouble codes: U0100 (lost comm. with ecm). |
15 | |
| 2006 Ford F-150 XLT 5.4L Misfire VIN: 1FTPW14V36 THANKS TO EVERYBODY FOR THE REPLIES. I DID WHAT EVERBODY SUGGESTED, ONE REPLY AT A TIME TO NO CHANGE IN VEHICLE. UP DATE VEHICLE INFORMATION, CUSTOMER BOUGHT VEHICLE WITH THIS PROBLEM AND HAS REPLACED RIGHT HEAD,TIMING CHAINS AND PHASERS, REPLACED BOTH CATS,RE... Trouble codes: P0300, P0303, P0316. |
21 | |
| 2010 Ford Mustang GT 4.6L Stall VIN: 1ZVBP8CH9A well it turns out it was in the timing chains , couldn't see it on a scope but changed had a bad gasket behind a chain tensioner. so we opened the timing cover and found some marks on the exciter ring and in the cover . I had doubts but proofs in the pudding ,... |
9 | |
| 2015 Ford Escape SE 1.6L Heater VIN: 1FMCU0GX4F There were a lot of good suggestions in the replies, and I've tried almost all of them. I know the heater hoses are not getting hot unless it's run for some time and I keep it reved up. I know the core flows well because I tried cleaning and found it passed wa... |
15 |
