 Prev |
Professional Automotive Repair Technical Discussions for August 6, 2017 International Automotive Technicians' Network (iATN) - Members Only |
Next  |
| (Also Available: All, Asian, Chrysler, European, Ford, GM.) | ||
| Vehicle Owners: If you are seeking an automotive repair professional to service your vehicle, visit the iATN Repair Shop Finder. | ||
Open Help Requests for All Makes and Models
| Help Request | Answers | |
| 1968 Ford Thunderbird 7.0L Plenum Chamber VIN: 1234576788 I know the dash has to be removed just wanted to see if anyone has done this and roughly how long it takes? I have a factory shop manual that illustrates the parts placements. Thanks for any help or advice . Jeff |
View | |
| 2002 Ford E-150 Econoline 4.2L oil pressure VIN: 1FTRE14252 Vehicle came in for a coolant leak found the metal tube elbow in the top of the intake had been patched and was leaking and some leakage at the water pump replaced both along with the thermostat. Engine started and ran fine in shop for 30 minutes then on the t... |
View | |
| 2006 Ford Ranger XLT 2.3L PCM Monitors VIN: 1FTYR10D56 The problem we're having is the monitors will not set for state inspection. No check engine light no codes. Coolant temperature, air intake temperature, and fuel level are all correct for a drive cycle. We have tested the EGR and EVAP system and are good. Car ... |
View | |
| 2010 Ford Escape XLT 2.5L Blend door VIN: 1FMCU0D78A Trouble code stored B12B7. Changed blend door actuator with a factory one, now I have 3 trouble codes B12A6, B12B7, and B12A5. Blend door lazy or slow to react. When set on cold it will stay for 60 seconds, then go warm for a few seconds, then switches back to... |
View | |
| 2004 Honda Accord EX 2.4L No Start VIN: 1HGCM72564 I have a cranks but no start 2004 accord 2.4 my scope is hooked up I have crank signal coils current ramped injectors current ramped good. fuel pump nothing I go to PGI main relay 2 which is pretty much a fuel pump relay and have power to feed side and control... |
View | |
| 2004 Volkswagen Jetta GLI 1.8L Slave cylinder VIN: N0AVAL1ABL Thanks in advance to everyone for help ...these VW Jetta coming with noise when applying clutch pedal I replace clutch set luk brand these is regular clutch not dual ..install transmission all OK until bleed system pedal feels good 15 pumps according with all ... |
View |
Fixes & Summaries for All Makes and Models
| Fix/Summary | Answers | |
| 2006 Infiniti QX56 5.6L Surge, MIL Lamp on VIN: 5N3AA08A96 Hi everyone,sorry for the delay regarding updates on this vehicle. I want to thank all eight techs who took the time to read and make suggestions regarding the fix. Im closing this as a fix as the owner of the vehicle decided to drive it for a few days before ... Trouble codes: P0335 (CKP Sensor crt.), C1130 (Engine signal 1), C1110 (Controller failure), C1146 (Side g SNSR CRT), B2573 (Bat.voltage), U1000 (Can comm.crt). |
9 | |
| 2005 Mercedes-Benz S430 4Matic 4.3L transmission VIN: WDBNG83J55 Thanks everyone for helping me out with this problem. I was able to read with my Launch scanner, the shifter gear position, which also occasionally from drive, wouldn't go to park. Unless you shot the engine off, and then all would go back to normal. I noticed... |
5 | |
| 1995 Other European E36 2500CC ECU Communications VIN: WBABF32060 Thanks to all who replied the info was all very useful and I am sure the answer will be in there, at the moment I am waiting to be able to have another look at the car and check through it! My initial thoughts on this have been confirmed so I must thank each ... |
9 |
