 Prev |
Professional Automotive Repair Technical Discussions for January 19, 2017 International Automotive Technicians' Network (iATN) - Members Only |
Next  |
| (Also Available: All, Asian, Chrysler, European, Ford, GM.) | ||
| Vehicle Owners: If you are seeking an automotive repair professional to service your vehicle, visit the iATN Repair Shop Finder. | ||
Open Help Requests for Asian
| Help Request | Answers | |
| 2002 Lexus LX470 4.7L Vsc VIN: JTJHT00W22 Sometimes when turning right, smoothly, at about 45 mph, with the brakes not applied, the yellow stability control activation light (picture of a car with skid lines)will blink and the chime will sound. When this occurs the car slows dramatically and it feel... |
View | |
| 2007 Lexus ES350 3.5L No Start, No MIL lamp VIN: JTHBJ46G97 Employee car being used to test some new head gaskets. Vehicle had blown both head gaskets. While waiting for parts to become available (several months) car would be periodically started & driven shortly to keep things moving. When the parts became available &... |
View | |
| 2005 Mazda 3 S 2.3L b2141 VIN: JM1BK12395 Car came in customer claimed it was struck by lightning. Could communicate with all modules except PCM. Tested and replaced PCM and Flashed. Car runs great just has code B2141 in Electric Hydraulic Power Assisted Steering (EHPAS) Control Unit. I'm using a snap... Trouble codes: B2141 (Module configuration procedure was not completed properly.) |
View | |
| 1997 Mitsubishi Eclipse Spyder GS 2.4L Stall VIN: 4A3AX35G9V This car will start and run fairly normal until the engine is shut off warm or cold and restarted. It will start, set the cam sensor code and stall. If the code is cleared or the battery cable removed it will start and run fairly well. I monitored cam and cra... Trouble codes: P0340 (Cam Position), P0505 (Idle Control) |
View | |
| 2014 Nissan Rogue S 2.5L No Start VIN: 5N1AT2MV6E Towed in for crank, no start. Tow truck operator started car and it blew alot of smoke(fuel). I was able to drive car into shop without incident. Parked car outside overnite, went to start and it wouldn't start. Battery tested good. No codes, good fuel, and no... |
View | |
| 1996 Toyota Avalon XL 3.0L Stall VIN: 4T1BF12B0T customer states that vehicle stalls about 2 times in a month,and usually happens when gone for a long drive and car sits for 20 minutes , it can be kept idling if you press on the gas , and eventually smooth out, one time it wouldn't rev up 2000 rpm , only hap... |
View | |
| 2002 Toyota RAV4 2.0L Misfire, MIL Lamp on VIN: JTEGH20V82 I have this rav 4 that is kicking my butt. it came in with a misfire on cylinder 2 and a lean code. I traced the misfire down to the no. 2 injector and replaced it. The fuel trim was reading 40 on long term. 20 on short term, after driving it a little bit the ... Trouble codes: P0302, P0171 |
View | |
| 2002 Toyota Highlander 3.0L engagement and upshifts VIN: JTEHF21A62 After another tech replaced the spark plugs, this car started having an intermittent misfire concern on 2, 4 and 6 (left or front bank). The parts store had sent us Bosch instead of Densos or NGKs. On a test drive it started this strange upshift pattern from 1... |
View |
Fixes & Summaries for Asian
| Fix/Summary | Answers | |
| 2015 Mazda 3 i SV 2.0L Cruise Control VIN: JM1BM1T78F We installed an aftermarket cruise control system. It is a Rostra 250-9634 that fits the 2014-2015 Mazda 3. It was fairly easy to install and worked well. You have to push the cluth the whole way to the floor to get the cruise to cancel. You cant just tap it ... |
2 | |
| 2006 Scion xB 1.5L Misfire VIN: JTLKT32406 I like to take the time to thank everyone who help me with his postings, I really appreciate it, the problem end up being the new injector , apparently was defective causing a rich condition, hence the misfire, new set of injectors did the trick, thanks again |
11 | |
| 2005 Toyota Tacoma 2.7L valve train VIN: 5TENX22N25 Thank all of you that replied to my help request. Like some of you said the lifters were pumped up and somehow they went bad after doing the head gasket. My initial thought was the lifters but Ive never had a problem where I do a head gasket and that happens. ... |
19 |
