 Prev |
Professional Automotive Repair Technical Discussions for August 31, 2016 International Automotive Technicians' Network (iATN) - Members Only |
Next  |
| (Also Available: All, Asian, Chrysler, European, Ford, GM.) | ||
| Vehicle Owners: If you are seeking an automotive repair professional to service your vehicle, visit the iATN Repair Shop Finder. | ||
Open Help Requests for Asian
| Help Request | Answers | |
| 2010 Honda Accord EX-L 3.5L oil consumption VIN: 5KBCP3F81A oil consumption problems, peeking in the valve cover is very clean, no sludge at all.one curious aspect is the dissapearance of oil is in consistant and it doesn't seem to matter if the oil has just been changed or it at the end of its interval.The pcv valve h... |
View | |
| 2009 Hyundai Accent GLS 1.6L long crank hard star VIN: KMHCN46C79 it has an long crank.once started runs fine. no misfires or hesitation or stalling. I replaced spark plugs. ckp sensor has been replaced for stalling on previous visit. any ideas or help would be great thanks. Trouble codes: P0650, P2177, P0171, P0300, P0301, P0302 |
View | |
| 2007 Infiniti G35 3.5L MIL Lamp on VIN: JNKBV61EX7 i m stumped on this one the light comes on after about a week i cleaned the maf sensor and donts see any exhaust leaks any help would be appreciated thanx in advance!! Trouble codes: P2A00 |
View | |
| 2007 Kia Optima LX 2.4L MIL Lamp on, limp mode VIN: KNAGE12347 Customer called with vehicle described as limp mode. Would not go faster than 20 mph. I advised stop and restart car, ran fine. Came to shop, per service manual, voltages all in range. Road tested fine. Cannot duplicate issue. Trouble codes: P0698, P2110 |
View | |
| 2007 Mazda CX-7 Touring 2.3L Hesitation VIN: JM3ER29357 This engine has me baffled. We rebuilt the engine based on a new short block(Not rebuilt), head rebuilt, new turbo, etc... In a nutshell, she starts and runs smooth, but under load(hot or cold)she bogs heavily till about 2500 rpm,then as boost picks up, she'll... |
View | |
| 2002 Mitsubishi Eclipse GT 3.0L Trans engagement VIN: 4A3AC54H52 Replaced auto trans in vehicle due to broken wave plate/ washer (no reverse or drive). after installed, used transmission will not engage in Drive or Reverse unless the engine is revved and when RPM drops to near idle, it drops back out of gear. Has Code 23 (P... |
View | |
| 2006 Nissan Frontier SE 4.0L stall/runs rough on VIN: 1N6AD07W46 We have a 2006 Nissan frontier LE 4.0l which intermittently will stall once on start up. When restarted, mil flashes quickly, abs light flashes and engine runs roughly and at low rpm with black smoke from tailpipe. No fault codes evident. It has happened to us... |
View | |
| 2010 Subaru Forester XT Limited 2.5L MIL Lamp on VIN: JF2SH6DC4A This vehicle has been in 3 times with CEL on with P0453-Evaporative System control pressure sensor high output. "Cruise" icon flashing. VDC icon on with C0057-VDC Control Interruption because of Engine Instruction/No CAN signal from ECM. 1 year ago we replace... Trouble codes: P0453 (Evaporative System Pressure Sensor), C0057 (Vehicle Dynamic Control Interruption) |
View |
Fixes & Summaries for Asian
| Fix/Summary | Answers | |
| 2006 Honda Accord LX 2.4L MIL Lamp on VIN: 1HGCM563X6 First of I wanted to correct the mileage. It is only 98k miles. There was no rodent damage. Engine got up to temp no problem & thermostat working normally. Finally fixed it with a used PCM. However the Immobilizer (anti-theft) module would not program to used ... Trouble codes: P0111 (Iat range performance problem), P1116 (Ect 1 sensor performance problem), P2610 (Ecm ignition off internal timer performance problem). |
4 | |
| 1989 Mitsubishi Van LS 2.4L Mechanical VIN: P25W020534 Again many thanks for all your help. I've talked with a couple of repair shops in Vancouver BC and I've got a couple of leads along with your suggestions so maybe I'll get this van fixed before the year is up :) |
4 | |
| 2007 Nissan Altima S 2.5L Accessories VIN: 1N4AL21E87 thanks for all the replies. according to some of the replies, which were right, the bcm needs a copy and paste programming. copy the info from the old bcm and put it into the new. my scantool will not perform this operation. so off to the dealer it went. |
6 |
