 Prev |
Professional Automotive Repair Technical Discussions for February 23, 2016 International Automotive Technicians' Network (iATN) - Members Only |
Next  |
| (Also Available: All, Asian, Chrysler, European, Ford, GM.) | ||
| Vehicle Owners: If you are seeking an automotive repair professional to service your vehicle, visit the iATN Repair Shop Finder. | ||
Open Help Requests for Asian
| Help Request | Answers | |
| 2002 Honda CR-V EX 2.4L Cat. monitor VIN: JHLRD78862 Has anyone had any luck getting the cat monitor to reset. The vehicle has been driven a full tank of gas. All different speeds. Does not code up, just wont reset the cat monitor. |
View | |
| 2010 Hyundai Sonata GLS 2.4L clicking fuel rail VIN: 5NPET4AC2A Howdy Y'all This Sonata has a clicking noise from the fuel rail. The customer is concerned about it even though we have no performance issues or codes. You can't hear it from drivers seat, only from under hood. If I put stethoscope on it the SAME noise can be ... |
View | |
| 2010 Lexus GX460 4.6L MIL Lamp on VIN: JTJBM7FX7A The truck runs fine and doesn't seem to be in limp in or anything like that. I want to put in a bank 1 (driver side) air switching valve, but the dealer told me I have to buy a whole kit including the pump, because there is trash in the system which will ruin ... Trouble codes: P106B |
View | |
| 2005 Nissan Altima S 2.5L No Start VIN: 1N4AL11D75 Hello everyone and HELP! I have this 2005 Nissan Altima 2.5 in that has been in a couple of times for intermittently cranking but not starting. The problem seems to be worst after it has sat for several hours. I have never been able to duplicate this problem.... |
View | |
| 2007 Nissan Quest SL 3.5L Fuel Level VIN: 5N1BV28U37 Presented with P0462 but no other codes or symptoms Customer thinks fuel gauge operating correctly Circuit is I/P Cluster Full Voltage to Sender (Variable Resistor) Sender Ground Back to I/P Which Moves Gauge Appropriately I/P Sends Voltage it sensed from S... |
View | |
| 2011 Nissan Altima 2.5L Hesitation VIN: 1N4AL2AP6B Car intermittently sets these two codes. Customer says it will start hard and be rough for a moment and then light will be on. We have wiggled wiring and connectors for all items on the circuit with the CKP and have test driven car but so far have been unable ... Trouble codes: P0335, C1130 (abs engine signal) |
View | |
| 2008 Toyota RAV4 Limited 2.4L MIL Lamp on VIN: JTMBD31V58 I have a 08 RAV 4 with a network problem. It came in the shop with the following warning lights on P/S,Air Bag, ABS and red brake light . also the tach doesn't work. I have no communication with these modules or the ECM. But I can communicate with the Air Bag.... |
View |
Fixes & Summaries for Asian
| Fix/Summary | Answers | |
| 1993 Honda Accord EX 2.2L Codes VIN: 1HGCB7677P I want to thank every one that took the time to respond to my request. You are what make this place GREAT!! Finally fixed! The problem was in the TCM as most of you suspected. The original issue was the VSS which was sending out a 12volts signal instead of... |
8 | |
| 2005 Hyundai Santa Fe GLS 3.5L charge VIN: KM8SC73E55 Thanks to all who replied. I pulled both lines off the compressor(thanks to AL from Florida) and HOOKED up our a/c machine and plugged both lines and now will pull a vacuum.Unfortunately the cust. declined repair but now i know for future references. Thanks ag... |
10 | |
| 2008 Mazda 3 i 2.0L Unknown VIN: JM1BK32F48 OK all sorry about the time on this one. I am waiting on the customer to return so I can look in to this further. Thanks for all the information and I will update this when they return. |
11 | |
| 2001 Nissan Maxima GLE 3.0L No Shift after getting hot VIN: JN1CA31D71 Thanks to everyone who took time and consideration to reply. The customer just could not do without their car, so they picked it up. How is an unemployed girl going to survive the weekend without her car? Very impatient people. I have still not been able to le... |
8 | |
| 2006 Nissan Maxima SL 3.5L ABS Module VIN: 1N4BA41E66 Yes, she is repaired! I replaced the ABS module and the large red fuse. Checked the CAN resistance; 60 ohms. High & Low CAN voltage 2.5 volts. Checked the ABS functions with Snappy, pump and solenoids work. All modules seem to communicate. Scan for ABS dtc... |
15 |
