 Prev |
Professional Automotive Repair Technical Discussions for October 7, 2015 International Automotive Technicians' Network (iATN) - Members Only |
Next  |
| (Also Available: All, Asian, Chrysler, European, Ford, GM.) | ||
| Vehicle Owners: If you are seeking an automotive repair professional to service your vehicle, visit the iATN Repair Shop Finder. | ||
Open Help Requests for European
| Help Request | Answers | |
| 2001 Audi TT 1.8L Cooling Fan VIN: TRUTX28N11 Fan speed remains the same with ac system on or off driving temp stays center gadge. Stop at light or idle for a while temp goes almost to the red cannot find any real testing for this unable to get a high sppd from fan assy thank you for your time in advance |
View | |
| 2004 Audi A4 Cabriolet 1.8L p3081 VIN: WAUAC48H14 I am trying to figure out what this means. I checked the coolant system and it is full. I looked at the thermostat housing and it looks new. I checked the reservoir cap and it only holds 8 pounds of pressure. I wondered about this. Someone has been looking at ... |
View | |
| 2003 BMW 325xi 2.5L Misfire, MIL Lamp on VIN: WBAEU33433 hey fellow car had bad oil leak from oil filter adapter gasket after replaced oil filter adapter gasket and oil filter and oil car runs rough and engine service light on code p0011.try to reinstallold filter back in did not make any difference. car was fine be... Trouble codes: P0011 |
View | |
| 2007 BMW 328i 3.0L Brake light on VIN: WBAVA33527 Hello guys I have this bmw with brake light on I hook my scanner and pulled a code for brake pad wear (they were low) I replace brake pads and also the sensor then I clear the code with my verus pro but code does not go away and brake light stays on. any sugg... |
View | |
| 2009 BMW X5 xDrive48i 4.8L Headlight VIN: 5UXFE835X9 Hi everyone and thanks in advance. I have a customer with this wonderful BMW and he is in love with it. It has this large stink bug (like a roach) in the drivers headlight and he would like me to remove it. I think I have found the re-re but would appreciate a... |
View | |
| 2009 Land Rover LR2 HSE 3.2L Active On-Demand Coupling VIN: SALFR24N99 when cold for the first few turns the active on-demand drive shudders and feels like it is slipping/grabbing and this happens in forward and reverse only when making a sharp turn |
View | |
| 1999 Porsche Boxster 2.5L Stall VIN: WP0CA2984X Car came in with rough idle on cold start, hesitation, CEL on. Original codes pulled were P1127 O2 sensing range cyl 1-3 P1129 O2 sensing range 2 cyl 4-6 and P0103 Hot film MAF. Cleared dtc and test drve watching MAF data doing third gear pulls, MAF reading ou... Trouble codes: P0102 (Hot film MAF sensor below lower limit) |
View | |
| 2006 Volkswagen Jetta 2.5 2.5L Cuts out, MIL Lamp on VIN: 3VWDF31K96 Tough one to diagnose here. 000818 trouble code for knock sensor is causing limp mode and engine not being able to rev over 3000rpm. This one is fairly intermittent. When accelerating in 5th gear, wide open, I can hear some light popping in the exhaust. Misfi... Trouble codes: 00083, 00081 |
View | |
| 2009 Volkswagen GTI 2.0L MIL Lamp on VIN: WVWEV71K79 This car came from the auction so I do not have the history behind it. First time starting it, it takes several time before it will start. This is what I have done so far. I found #2 rocker arms off. Checked for damage and reinstalled. Removed timing cover to ... Trouble codes: P0340 |
View | |
| 2010 Volkswagen Tiguan S 2.0L No Start VIN: WVGAV7AX0A Chrysler dealer I used to work for ask me to take a look at this used VW. Car was running great, parked it on lot, detail guy comes to get it, cranks, no start. I performed vehicle scan, no communication with ECM. TCM and other modules logging loss of communic... Trouble codes: 01314 (Sporadic communication), 00956 (Central electric module. no adaptation.) |
View |
Fixes & Summaries for European
| Fix/Summary | Answers | |
| 2009 Audi Q5 Premium 3.2L air injectio VIN: WA1KK78R09 secondary air pump was full of water and vehicle had a collision a year ago I did change the pump but the PCM will not do any commands when asked , I also did find some wiring issues so I would say the pcm is either lost its programming or... |
3 |
