 Prev |
Professional Automotive Repair Technical Discussions for August 6, 2015 International Automotive Technicians' Network (iATN) - Members Only |
Next  |
| (Also Available: All, Asian, Chrysler, European, Ford, GM.) | ||
| Vehicle Owners: If you are seeking an automotive repair professional to service your vehicle, visit the iATN Repair Shop Finder. | ||
Open Help Requests for Chrysler
| Help Request | Answers | |
| 2007 Chrysler PT Cruiser Limited 2.4L Light On VIN: 3A4FY58B27 Just installed a tipm. Now will not communicate with abs. Tried network config, did not work. Have account with techauhtority. New to chrysler programming. Any suggestions? |
View | |
| 2000 Dodge Ram 1500 Van 5.2L Poor Idle Quality VIN: 2B6HB11Y7Y Complaint is when starting vehicle cold it runs ok for a few seconds then starts spitting and sputtering, if you give it some gas the problem goes away until the next cold start. There is no MIL and no codes. vacuum is 18 in. at idle, checked for manifold vacu... |
View | |
| 2006 Dodge Charger R/T 5.7L Cuts out VIN: 2B3KA53H56 I have this 06 hemi charger with an instant stall. This mainly happens hot but also can happen cold. Plugs were replaced with mopar plus the crank sensor also mopar. I have had this type of stall before but cold usually. This car will actually clear codes and ... Trouble codes: U0100, P0700 |
View | |
| 2007 Dodge Sprinter 3500 3.0L a/c VIN: WDPPF44537 A/c unit was activating only when maniputating on/off and temp / door buttons, then would only plow cold for a few min. Then stop. Because of the control head malfunction replaced with used controler. Now blows cold untill you drive, then starts to blow hot. T... |
View | |
| 2008 Dodge Ram 2500 SLT 6.7L Stall VIN: 3D7KS28A08 This is for the Dodge diesel techs. Before we get started this truck had had the egr deleted and programmed. Truck was towed in with complaint of stalled while driving, then restarted ok. Next stalled and no start no spin. When the truck arrived the following ... Trouble codes: U0100 (Loss of comm pcm/ecm), U0141 (Loss of comm with tipm) |
View | |
| 2005 Jeep Wrangler Unlimited 4.0L MIL Lamp on VIN: 1J4FA44S85 Hey gang, This vehicle came in with an B2S2 heater circuit fault that another shop didn't want to spend any more time with. The downstream oxygen sensor had a broken connector and was zip tied together. I replaced the pigtail for the sensor and that corrected ... Trouble codes: P0138 (O2 Sensor Circuit High Voltage Bank 1 Sensor 2), P0158 (O2 Sensor Circuit High Voltage Bank 2 Sensor 2) |
View | |
| 2012 Ram 2500 ST 5.7L Poor Idle Quality, Hesitation, Misfire, MIL Lamp on VIN: 3C6TD5HTXC Hello IATN guys, This vehicle came to us from a fleet company which has a good reputation for maintaining their fleet and who idles their trucks to death. Customer concern is that the truck runs poorly and has a check engine light on. The main reason im puttin... Trouble codes: P0302 (Cyl 2 misfire detected), P2299 (Brake pedal position/ Accelerator pedal position incompatable) |
View |
Fixes & Summaries for Chrysler
| Fix/Summary | Answers | |
| 2001 Chrysler Sebring LXi 3.0L unknown VIN: 4C3AG52H01 Thanks everybody. We began by flushing out the system so we knew how much oil we had in it. Recharged it and it seems to work much better now. Will always use factory parts for jobs like this from now on. |
22 | |
| 2006 Chrysler Sebring 2.4L cooling fans The problem ended up being high resistance in the connector for the coolant sensor. Repaired the connector and installed a new sensor. Thanks to all for your input. |
10 | |
| 2001 Jeep Grand Cherokee Limited 4.7L No Start VIN: 1J4GW58N11 Thanks for all the replies. Disconnected the harness with the 5v reference from PCM.. Was able to communicate with the computer and pulled up a problem with the oil pressure sensor circuit.. Harness had wires showing. Repaired wiring harness and all is good.... |
12 | |
| 2007 Jeep Wrangler X 3.8L steering linkage VIN: 1J4FA24107 most replies I received concerned disconnecting outer tie rods and turning wheels to see if one or more ball joints or tie rod ends were binding, one mentioned a control arm on rear axle which if bushings were worn might cause the memory steer problem. Custome... |
14 |
