 Prev |
Professional Automotive Repair Technical Discussions for May 22, 2014 International Automotive Technicians' Network (iATN) - Members Only |
Next  |
| (Also Available: All, Asian, Chrysler, European, Ford, GM.) | ||
| Vehicle Owners: If you are seeking an automotive repair professional to service your vehicle, visit the iATN Repair Shop Finder. | ||
Open Help Requests for Asian
| Help Request | Answers | |
| 2006 Acura TL 3.2L Reverse back-up sensor system VIN: 19UUA65556 Hello to all iATN members. I am seeking some professional/ Acura guidance on my aunt's 2006 Acura TL. She asked for my help in diagnosing a new concern with her vehicle. She states that her reverse back-up sensor system, which is an original option to the car,... |
View | |
| 1996 Honda Civic DX 1.6L ?rotary air control valve VIN: 2HGEJ6342T Quite suddenly two days ago this car began to surge severely when engine reached normal operating temperature (previously it had performed flawlessly.) Car idles normally when engine is cold; however, once it reaches normal operating temperature it begins to s... |
View | |
| 2008 Honda Civic DX 1.8L Cuts out VIN: 2HGFA15468 The car runs great off idle all speeds with no problem Except when coming to stop and idle. Touch the throttle lightly it stalls. Scanned the TPS it is responding. Small Touch on the Gas Pedal it stalls ??? |
View | |
| 2006 Mazda Tribute i 2.3L Belt Pulley VIN: 4F2YZ02Z66 Owner has had vehicle since new & the first time the Serpentine Belt Idler Pulley bolt broke & threw the belt off was 2-5-13 at 64K miles. We Towed it in, installed a New OEM Mazda Idler Pulley with attaching bolt as that is how it is sold the bolt & pulley co... |
View | |
| 2009 Nissan Altima S 2.5L Suspension VIN: 1N4AL21E19 This vehicle has a sharp popping noise over bumps on the LF. It also pops sometimes when you hit the brake. Nothing is visibly loose in the LF. The spring is intact. I found a recall for strut mounts but it is not applicable to this car. Any Nissan techs famil... |
View | |
| 2011 Nissan Versa S 1.8L No Start VIN: 3N1BC1CP9B I have had the vehicle for a couple of days, fuel pressure has never dropped below 51 psi. There are no codes, all monitors have been ready, confriming all crucial systems have passed. Ofcourse, since i have had the vehicle, i can not duplicate the problem. I ... |
View | |
| 2007 Toyota 4Runner SR5 4.0L Heater/Cooling box VIN: JTEZU14R17 This is a stumper, this vehicle in recir mode at idle or running at operating RPM range, will not throw cold air at the vents. I have tried pinching off the heater core lines to eliminate the possibility of heat bleeding into the cooler chamber, and no noticea... |
View |
Fixes & Summaries for Asian
| Fix/Summary | Answers | |
| 2002 Hyundai XG350 3.5L Accessories VIN: KMHFU45E92 evening techs, the customer declined repairs- saying she is just going to "dump" the car. What I found was that the ETACM was causing the draw, but the customer did not want to spend the money? I know this does not help, but I appreciate all the help Steve L... |
2 | |
| 1999 Lexus RX300 3.0L MIL Lamp on VIN: JT6HF10U5X Installed new different part. T'd off of the hose that was t'd on the old one and caped off the extra port on the sensor. Vehicle passed an emission test reset all readiness monitors and stayed gone. Thank you for the help. Trouble codes: P0441. |
4 | |
| 2007 Suzuki XL-7 3.6L brake lamps VIN: 2S3DB21737 Many thanks to Richard from California for the extremely valuable information..the vehicle has left and is yet to return, but when and if it does, I think I'll be ready with the helpful information you have given me, that Alldata couldn't..again, thanks! |
2 | |
| 1997 Toyota Camry CE 3.0L license plate lights VIN: 4T1BF22K8V Most of the replies indicated the same information, that the part of the lighting harness that runs up the left hinge is where the problems occur. I followed the wires by spreading the plastic conduit until I got to the hinge where not just 1, but 4 wires were... |
18 | |
| 2003 Toyota Tundra SR5 4.7L ABS Module VIN: 5TBBT44113 Thank you everyone for your replies and advice. Per Ted's recommendations, we tried scoping the ABS sensors on a graphing meter. Grabbing wires and trying to spin the wheels for a wave signal didn't produce a very accurate wave for comparison among all the sen... |
16 |
