× Auto Repair Pros Member Benefits TechHelp Knowledge Base Forums Resources My iATN Marketplace Chat Pricing About Us Join Industry Sponsors Video Members Only Repair Shops Auto Pro Careers Auto Pro Reviews
Join Now
International Automotive Technicians Network
Prev Professional Automotive Repair Technical Discussions for April 21, 2014
International Automotive Technicians' Network (iATN) - Members Only
(Also Available: All, Asian, Chrysler, European, Ford, GM.)
Vehicle Owners: If you are seeking an automotive repair professional to service your vehicle, visit the iATN Repair Shop Finder.

Open Help Requests for Chrysler
Help Request Answers
2002 Chrysler 300M 3.5L Need service number VIN: 2C3HE66GX2
Good afternoon to all, i need some help from chrysler techs. I have the above vehicle that needs a new ecm (lost the driver to ignition coil #2).i took the old one off so i can get the numbers off of it, so i could call the rebuilder that we use and it has no ...
2004 Chrysler Crossfire 3.2L MIL Lamp on VIN: 1C3AN69L54
This car was towed in after customer hit pot hole & blew out left front tire. He stated that after hitting pot hole all warning lights on dash came on, speedometer quit & transmission would not shift. We replaced tire & cleared codes with VERUS which states ca...
1997 Dodge Dakota 3.9L Unknown VIN: 1B7GG23X2V
Vehicle came in about a month ago for what they/we determined was fuel in oil with minor drive-ability issues (hard start, start stall)and the oil light on at idle. About one quart over full. The plugs were well worn, not wet, cap and rotor ok. Replaced plugs,...
2012 Dodge Grand Caravan SXT 3.6L Brakes
Hello all have a 2012 Grand Caravan, came in with a fading brake pedal, did various tests, determined that we needed new master cylinder, replaced it and brakes work great now but i have the brake light on, the park brake pedal is not engaged, the fluid is up ...
1997 Jeep Wrangler Sport 4.0L shift VIN: 1J4FY19S9V
Replaced clutch assy, including bearing, pressure plate. Flywheel checked ok . After job was done, and Hydraulic system was bled, vehicle shifts most of the time but grinds a lot. I replaced slave cylinder. because I found it leaking at bleed valve. I bled sys...
2010 Jeep Wrangler Unlimited Sport 3.8L steering/suspention VIN: 1J4BZ3H13A
We need a direction to go at this point. This Jeep wrangler 4 door has The death wobble. On inspection we found the upper and lower ball joints loose, and the left and right tie rod and end loose. These components were changed. all other components are tight. ...

Fixes & Summaries for Chrysler
Fix/Summary Answers
2001 Chrysler PT Cruiser 2.4L iac VIN: 3C8FY4BB01
I appreciate all the information others have sent to me. the replies although I had already done most of the testing was not much help but it helped me go in the right direction. sorry I do not have a fix for this vehicle as the customer has pulled the vehicle...
2011 Chrysler Town & Country Limited 3.6L Starting VIN: 2A4RR6DG8B
Special thanks to Jerry from Ohio Mar 14, 2014 11:42:09 AM You can usually get them out if you pull hard enough...first question are there any codes stored or active...I have disconnected battery and reconnected before and the WIN came back to life... Yo...
1993 Dodge Dakota 3.9L Mechanical VIN: 1B7FL23X6P
Well guys I want to thank all of you for your replies this Dakota actually had a few issues 1 being the brake pads they were of a poor design and the second set I put on were worse and finally the 3rd set were a lot better, 2 the drums were under spec and out ...
2005 Jeep Grand Cherokee Limited 4.7L Oil pressure VIN: 1J4HR58N75
Darin you win the prize. The intermediate sprocket bolt was left out. Tech was performing this head job and an engine R&R side by side and he thought the bolt was for the other job. Took front cover off, put bolt back in and no more problems. Thanks guys y'all...
Prev (Also Available: All, Asian, Chrysler, European, Ford, GM.) Next