 Prev |
Professional Automotive Repair Technical Discussions for October 22, 2013 International Automotive Technicians' Network (iATN) - Members Only |
Next  |
| (Also Available: All, Asian, Chrysler, European, Ford, GM.) | ||
| Vehicle Owners: If you are seeking an automotive repair professional to service your vehicle, visit the iATN Repair Shop Finder. | ||
Open Help Requests for Chrysler
| Help Request | Answers | |
| 2000 Chrysler Voyager SE 3.3L I / M flags VIN: 2C4GJ45G2Y Time for emission testing and vehicle will not pass O2, Cat, & EGR self test. Customer has driven hundreds of miles. No codes. I have done Emission drive cycles a number of times. All data looks good, no power loss. |
View | |
| 2001 Chrysler Town & Country EX 3.8L pci bus VIN: 2C8GP74L51 I check wiring diagrams onmy mitchell and all data for pci short to ground or power,continuiti ok . I not have 7.5 v on pci lines I check pin 2 on dlc to 7 on juntion port and ok I belive is the pcm vin program but Inot shure I don't have drb only multimeter I... |
View | |
| 2003 Chrysler Sebring LX 2.4L starter VIN: 1C3EL46X23 a month ago this car came in as a no start. when you tried to start it the starter would just start to engage then stop. the data in our modis did not show any security problem. as I worked my way down the starting circuit I got to the starter relay and the ca... |
View | |
| 1977 Dodge B300 7.2L No Start Have no spark (most og the time). No spark cranking. Sparks when letting off the key. I have 335mv from the distributor at the module, cranking. I have 11.2v @ the coil + cranking. Coil - reads about 1 v KOEO. The resister reads 11.2v at the pink wires, and 7.... |
View | |
| 1999 Dodge Durango SLT 5.9L 1-2 Shift VIN: 1B4HS28Z9X Vehicle came to us wont shift out of low gear at times.put the derb3 on it ,no codes.watching data stream,desired pressure will pick up [...] rpm but no actual pressue.ohmed all possible trans sensors from tcm,all is good.removed the pan to check install of... |
View | |
| 2000 Dodge Durango 5.9L Excessive Emissions, Hesitation, Cuts out, Stall VIN: 1B4HR28Z4Y good morning to all, I have a durango here that has me scratching my head. Came in with code p0601 stored. Anyway, the truck will start and run if you keep your foot on the gas. While you are holding it it will cut-out like power interuption.Every time it does... Trouble codes: P0601 |
View | |
| 2000 Dodge Dakota SLT 4.7L Unknown VIN: 1B7GG2AN6Y So I'm having trouble finding out what is wrong with this truck. Came in at first with check engine light on with no code but trans was in limp mode. Looked at data display and trans side the rpms and every thing didn't change with throttle pedal they were rea... |
View |
Fixes & Summaries for Chrysler
| Fix/Summary | Answers | |
| 2001 Chrysler 300M 3.5L oil leak VIN: 2C3AE66G51 Hello everyone. We replaced the oil pan gasket on this car and it seems to be doing fine. |
6 | |
| 2004 Chrysler Concorde Limited 3.5L No Start, Stall VIN: 2C3AD56G04 Thanks for all inputs. the car is fixed several days agao and today the owner ships back his another key to be matched with the new immobilizer. I didn't get the PIN and we sent the car with a new immobilizer to a nearest dealer shop. It costs 65 usd to put th... Trouble codes: P0513 (sentry key immobilizer module), P0340 (camshaft position sensor), P0344 (camshaft position sensor). |
6 | |
| 2005 Dodge Sprinter 3500 2.7L Starts then stalls VIN: WD0PD54435 Aloha and thank you to everyone that replied, all the info was important and relevant. The very first time I touched this Sprinter I found the trans dip stick cover sitting in the cowl along with nuts and bolt from the turbo heat shield and the negative bat... Trouble codes: P2133 (001- Glow Plug1 Circuit Short To Voltage), P2134 (001- Glow Plug2 Circuit Short To Voltage), P1482 (001- Glow Plug Module Excessive Current). |
9 | |
| 2006 Dodge Charger R/T 5.7L No Start VIN: 2B3KA53H76 i had all ready gone through and unpluged each of the sensor on the 5volt line and had gone as far as cutting the wires at the ecu to see if voltage would come back it did not . i applied 4.5 volts to the wiring harness side and it would show up on the scanner... Trouble codes: P0652, P0642, P2127, P2122, P0118, P0198. |
6 |
