|Prev||Professional Automotive Repair Technical Discussions for May 29, 2013
International Automotive Technicians' Network (iATN) - Members Only
|(Also Available: All, Asian, Chrysler, European, Ford, GM.)|
|Vehicle Owners: If you are seeking an automotive repair professional to service your vehicle, visit the iATN Repair Shop Finder.|
Open Help Requests for Chrysler
|2001 Chrysler Town & Country (Van) EX 3.8L driver side power sliding door VIN: 2C8GP54L41
Hello Everyone, I have a Power Sliding door on the driver side that doesn't open fully when it's only cold. When we push the sliding door switch the door pops open but will not slide open. The door is not binding and will start to work after helping the door o...
|2004 Chrysler Sebring LX 2.4L steering wont return VIN: 1C3EL46XX4
vehicle came in with a suspension noise and the steering wheel not returning to center. we replace lower ball joints and rack & pinion. noise is now gone but steering still does not return to center. we aligned, but tech is not here to ask about caster. any id...
|2004 Chrysler Pacifica 3.5L MIL Lamp on
did a timing belt with napa parts. came back 2 days later with the check engine light on, P0306. owner said since it never had a tune up and 200k + miles. we did one with plugs and boot ends. coils all ohm out the same but changed coils other bank. still have ... Trouble codes: P0306 (missfire cyl 6)
|2001 Dodge Ram 3500 Truck 5.9L Drive-axles VIN: 2B5WB35Z71
Hi all in IATN land. Thanks for taking the time to read this post. Van came from another shop. Customer compliant is a harmonic vibration that comes in at 55mph and gets worse as you go faster. I drove it and it is a harmonic vibration. I checked and corrected...
|1993 Eagle Talon ES 2.0L Misfire VIN: 4E3CF44E9P
Hi all in IATN land. I have a real stubborn one here. Came to me from another shop. Many of the parts listed had been replaced befor it got hear. I have repaired all but one issue. There is a hard intermittent chop at idle and at cruise. Feels and sounds like ...
Fixes & Summaries for Chrysler
|2001 Chrysler PT Cruiser 2.4L No Start VIN: 3C8FY4BB61
I'm going to call this one fixed. Most suggested a wiring harness/ground issue causing all three sensors to read high and I agreed. Took the air cleaner assembly out and found several grounds on the left side fender well. Didn't really find a smoking gun but a... Trouble codes: P0118, P0123, P1193 (Air Inlet Temp Sensor Voltage High).
|2004 Dodge Ram 2500 Truck ST 5.9L speed control VIN: 3D7KA28C74
I found that the Speed control Supply that runs from the PCM through the brake switch to the Servo is monitored by the PCM. This circuit was shorting out @ the Dump valve wich is part of the Cruise Servo.FYI BRAKE RAT means the rationality between the two brak...
|2004 Dodge Stratus SE 2.7L Surge, MIL Lamp on VIN: 1B3EL36T94
Sorry for not posting the fix earlier, I ordered the part from Daves source saved 70 bucks,thank you Dave your the man. I replaced the map sensor the old one came out with lots of oil on it im thinking the oil compromised the diaphragm in the sensor im thinkin... Trouble codes: P0108, P2074.
|2005 Dodge Neon SXT 2.0L extended crank VIN: 1B3ES56C75
First thanks to all the help, especially Eddie from Georgia, for taking time out to email me. After comparing scope patterns to know good. Finally realized was not paying close enough attention, I was looking at shape and for any drop out, and did not realize ... Trouble codes: P0344 (Cmp).
|2002 Jeep Liberty Limited 3.7L suspension VIN: 1J4GL58K32
I got a lot of good experienced advice on this problem Jeep. Five out of ten car doctors agree that Jeep ball joints are junk. I tested these for slack and found none, but replaced them anyway. I replaced the hubs as well. The popping persisted. Swapped the st...
|2003 Jeep Grand Cherokee Laredo 4.0L power windows VIN: 1J4GW48S93
Well it has been five days and customer called me to say everything is fine so were calling this a fix. Chip and Charlie both nailed it. I disconnected the battery because boss does not like any electrical problem in shop overnight. Next morning hooked it b...