 Prev |
Professional Automotive Repair Technical Discussions for May 21, 2013 International Automotive Technicians' Network (iATN) - Members Only |
Next  |
| (Also Available: All, Asian, Chrysler, European, Ford, GM.) | ||
| Vehicle Owners: If you are seeking an automotive repair professional to service your vehicle, visit the iATN Repair Shop Finder. | ||
Open Help Requests for Ford
| Help Request | Answers | |
| 1965 Ford F-100 Pickup 3.9L coil I need to get it running so I can sell it. There is no license or registration on it. I need to talk to an old ford technician so I can find the VIN number so I can apply for a lost title. |
View | |
| 2000 Ford F-250 Super Duty Lariat 7.3L banging VIN: 1FTNX20F4Y power stroke tech HELP!! 2000 f250 7.3 turbo. at cruse speeds or light accel, a gurgling sound starts then a ganging noise like fire crackers going off under the hood. soon as you let off the power a little it goes away. roll back in the gas and it starts agai... |
View | |
| 2002 Ford Ranger Edge 3.0L power steering pump VIN: 1FTYR14U52 need some help here i have this truck with a power steering pump is noisey so i replaced the pump with a after market pump and flushed the lines, bleed the system under vacume to make sure all air was out, pump is still noisey so thinking that i have a bad pum... |
View | |
| 2002 Ford F-250 Super Duty Lariat 5.4L No Start VIN: 1FTNW21L72 Truck arrived on flatbed no start. Engine cranks but no start.checked fuel press 35#psi koeo.has no injector or coil pulse when cranking. Engine has no codes , we have data with motis. Nothing looks out of the ordinary.every now and then engine will start up a... |
View | |
| 2002 Ford F-150 King Ranch 5.4L Convertor? VIN: 1FTRW07L02 Vehicle runs fine and shifts fine, no codes for eng. or trans. Only problem is a driveline "bang" or "clunk" (once) when convertor unlocks, right at the moment of unlock. Does it everytime convertor unlocks IF there is a good hill and/or moderate throttle. No ... |
View | |
| 2006 Ford Escape Hybrid 2.3L Starting VIN: 1FMYU96H76 Code poa05 and p1aod in system checked mec pump not working replaced pump pushed reset for rear battery for charge and installed charger on front battery code p1a0d still in system can not clear car will still not start or crank just a click from relay under d... |
View | |
| 2006 Ford Freestyle SE 3.0L Unknown VIN: 1FMZK01156 first time so thanks for any help .Got this car in from a local repair shop.They have replaced the engine ,flywheel and torque converter .It has a noise thats sounds like a broken flywheel witch sounds like it is coming from flywheel, torque area. Sometimes th... |
View | |
| 1969 Lincoln Mark III 7.5L blower motor VIN: 9Y89A89683 The car came into shop with no blower motor operation. The A/C compressor does function through the controls. Located blower motor wires and jumped to 12 volt source. Motor runs fine. Checked all fuses and circuit breakers in and behind glove box. Need a schem... |
View |
Fixes & Summaries for Ford
| Fix/Summary | Answers | |
| 1997 Ford F-250 Lariat 5.4L Monitors VIN: 2FTFF28L8V We have been unable to get this vehicle through emissiosn due to multiple monitors not running. I was given many suggestions and also referred to the Ford specific information to no avail.Some suggestions included: 1)Check to make sure this is not over 8600# -... |
30 | |
| 1997 Ford F-250 Lariat 5.8L engine VIN: 1FTHX25H9V Removed ballencer on inspection it was slipping. Thanks |
4 | |
| 2001 Ford F-150 XL 4.2L ign.,injecto VIN: 1FT2X17281 Thank you for the assistance. It was the CPS. Without having a scope, I pulled the old one off and could see that it was bad for the magnet had rusted all ont. Hitting that pot hole finally finished it! Matt |
7 | |
| 2001 Ford Focus SE 2.0L convertor VIN: 1FAFP34P51 Replaced the soleniods that relate to TCC no difference. It acts the same when I unplug trans connector. Customer declined further testing at this time |
9 | |
| 2003 Ford Escape XLS 3.0L ride control VIN: 1FMYU021X3 I hope I fixed this car. With the complete sturt assembly. Time will tell. Thanks to all for the replies.I know if we used just OE equipment we would have less problem but with money now days in smaller towns we could not last long in business. Thanks again fo... |
5 |
