× Auto Repair Pros Member Benefits TechHelp Knowledge Base Forums Resources My iATN Marketplace Chat Pricing About Us Join Industry Sponsors Video Members Only Repair Shops Auto Pro Careers Auto Pro Reviews
Join Now
International Automotive Technicians Network
Prev Professional Automotive Repair Technical Discussions for August 1, 2012
International Automotive Technicians' Network (iATN) - Members Only
(Also Available: All, Asian, Chrysler, European, Ford, GM.)
Vehicle Owners: If you are seeking an automotive repair professional to service your vehicle, visit the iATN Repair Shop Finder.

Open Help Requests for Chrysler
Help Request Answers
1998 Chrysler Town & Country LXi 3.8L a/c system VIN: 1C4GP64L9W
This 98 Town and Country came in blowing warm air. I tested pressures and they were 36 on low side and 75 on high side. This high pressure is too low but I cannot get it to raise. I have replaced the compressor, expansion valve, and accumalator/dryer and recha...
2008 Chrysler Town & Country Touring 3.8L Transmission VIN: 2A8HR54P88
Got one here than I need a little help with. 2008 Chrysler Town and Country van with a 3.8 and six speed auto transmission. The van was brought to us from the body shop for a transmssion leak. It had been hit in the LF corner mostly. Discovered that the valve ...
2003 Dodge Ram 3500 5.9L brake lights VIN: 3D7MU48C93
The brake lights on the bed stay on with the key. check for dtc in the fcm and the instrument cluster. also used scanner to watch PID data in the instument cluster, it switches open and closed when going on the brake. Tested the brake switch and for signal to ...
2008 Dodge Grand Caravan SE 3.3L pedal VIN: 1D8HN44H38
Hello all, i have a little issue , i think that i am going the right direction but i thought i would get a few opinions , this van has a soft brake pedal, it will stop preety good but the pedal just goes down very slow almost to the floor, i locked the wheels ...
2004 Jeep Liberty Sport 3.7L Mil VIN: 1J4GL48K74
This Jeep Liberty came in with no codes with all monitors passed. Went through the normal routine and then put it out on the lot for sale. Now it wont pass the cold start EVAP test. Within 5 minutes P0441 (Evap Purge Solenoid Performane) is stored in pending c... Trouble codes: P0441, P0443
2007 Jeep Commander Limited 5.7L 4x4 system VIN: 1J8HG58257
This commander has the message "service four wheel drive" on the instrument cluster. The message only shows up occasionally when the key is turned on. Only code in any module is b2185 stored in central gateway. All gearbox fluids are like new. Any help will be...
2008 Jeep Grand Cherokee Laredo 3.0L MIL Lamp on VIN: 1J8HR48M68
P0600 serial data connector-no drivability concerns, vehicle has had same code cleared and resets after a while, cannot find ANY info in Alldata, IATN archives-any help appreciated, Brian. Trouble codes: P0600

Fixes & Summaries for Chrysler
Fix/Summary Answers
1998 Chrysler Cirrus LXi 2.5L Poor Idle Quality, Hesitation, Stall VIN: 1C3EJ56H2W
Thanks for all the suggestions - turns out you were all right :-) I pulled the EGR valve and tube and found a LOT of debris in the tube at the intake manifold end. The tube was necked down to about half the original size. Cleaned out the tube, manifold and v...
2002 Chrysler PT Cruiser Dream 2.4L cooling fan motor VIN: 3C8FY68B52
sorry it took so long to post fix. this one turned out to have a faulty pcm. for some reason pcm would not signal hi speed fan relay on its own. only if i commanded it. thanks for all your help.
1997 Dodge B2500 5.2L MIL Lamp on VIN: 2B7HB21YGV
Just when it seemed this one would be a returning headache it wasn't. When I learned the Adaptive numerator is determined during hard decel, I was sure the problem was an internal engine issue causing a too unstable signal at the crank sensor. The owner used t... Trouble codes: P1398 (Missfire Adaptive numerator at limit).
2003 Dodge Sprinter 2500 2.7L Cuts out, MIL Lamp on, limp mode VIN: WD2YD34122
Thanx to all who sent replies. The problem with it going into limp mode was the air intake tube going to the intake manifold was cracked. Replaced it and runs well. No more going into limp mode. Still haven't figured out why scanner isn't communicating but at ... Trouble codes: P2316, P2400, P2401, P2310, P2311, P2312.
Prev (Also Available: All, Asian, Chrysler, European, Ford, GM.) Next