 Prev |
Professional Automotive Repair Technical Discussions for March 29, 2012 International Automotive Technicians' Network (iATN) - Members Only |
Next  |
| (Also Available: All, Asian, Chrysler, European, Ford, GM.) | ||
| Vehicle Owners: If you are seeking an automotive repair professional to service your vehicle, visit the iATN Repair Shop Finder. | ||
Open Help Requests for Chrysler
| Help Request | Answers | |
| 2003 Chrysler Town & Country Limited 3.8L 1-2 shift VIN: 2C8GP64L43 When hot at light throttle the 1-2 shift has harsh double bump not a slip bump or flare shift. Under very light throttle or medium to heavy throttle the shift is perfect. Pinion factor is correct and computer relearn has been performed, have driven 200 miles w... |
View | |
| 2009 Chrysler 300 Touring 3.5L Oil Dash Light VIN: 2C3KA53V49 I need help on this one vehicle came in with low oil light on and I replaced the oil sender switch light go's out but not until you start it and then turn it off and restart i have oil pressure and voltage to sensor but have never seen this before only after y... |
View | |
| 1997 Dodge Ram 1500 Laramie 3.9L Misfire, Backfire VIN: 1B7HC16XXV Truck came in with misfire on cylinder 5. Traced it to plugged injector, so cleaned it and off it went running great. Comes back three days later and it is backfiring, no power, hesitation. No misfire counters present, no codes. Suspect timing (chain is rattli... |
View | |
| 2001 Dodge Grand Caravan Sport 3.3L Hesitation, Cuts out, Misfire VIN: 2B8GP44341 Thanks in advance for all your help. At 40 mph vehicle has very light misfire 2 times or chuggle. If it was my vehicle i would keep driving. I have checked fuel pressure and spark both are within spec. When problem occurs the only thing i see in scan tool is s... |
View | |
| 2004 Dodge Stratus SXT 2.4L No Start VIN: 1B3EL46X64 Vehicle is driving us nuts. Hoping some of you guys have run across this before. Vehicle originally came in for a no start. It had no spark. Replaced ignition coil and fired right up. 1 Week later vehicle came back no start. Was actually towed in. Vehicle fire... |
View | |
| 2005 Dodge Neon SE 2.0L No Start VIN: 1B3ES26C15 05 Neon, no start,P0513-no skim key. I could really use some Chrysler help. Car was brought in for no start. No starter operation or anything. There was no communication from PCM. Went to ck. powers and grounds at PCM, found computer was full water and termina... Trouble codes: P0513 |
View | |
| 2007 Dodge Ram 2500 TRX4 5.9L No Start VIN: 3D7KS28C67 This truck came to me no start HOT...I found when HOT the High pressure fuel was only going to about 400psi...I ran every test in the book and found no problem...I replaced the pressure relief valve on the common rail (with a factory Cummins valve) and the pro... Trouble codes: P0480 (testing and results) |
View | |
| 2003 Jeep Liberty Sport 3.7L Electronic VIN: 1J4GL48K93 Hi, techs, Have this Liberty thats kicking my butt. Came in with trans in limp mode and tried to pull codes- no communication. I checked all fuses -good. went to controller and checked pin 56 - 12 volts- no power on pins 16 and 17 which means relay is not tur... |
View | |
| 1997 Plymouth Voyager 3.0L Misfire, Poor Fuel Economy VIN: 2P4FP2531V This van was given to me, and I use it for my business. Runs well but gets poor fuel economy. Seems to misfire under cruse conditions. I obtained these rather odd codes from a new scan tool, the Maxidas, 071C, 071D, 071E, 071F, 0720, 0721, 0722, 0723 described... Trouble codes: P0134 (Heated Oxygen Sensor Bank 1 Sensor 1 Signal Remains At Center), 071C, 071D, 071E, 071F, 0720 (system rich R-Idle adapt at lean limit U3F) |
View |
Fixes & Summaries for Chrysler
| Fix/Summary | Answers | |
| 2004 Chrysler Town & Country Touring 3.8L 2nd VIN: 2C4GP54L84 Thanks to everyone who took the time to assist me with this problem. I've replaced the IPM and voalla "FIXED". THANKS AGAIN!! |
7 | |
| 2002 Dodge Ram 2500 5.9L Governor pressure VIN: 3B7KC26ZX2 Thanks for all the suggestions. It turned out to be a bad PCM. Most of you said to hook up the pressure gauge to verify what I was seeing on the scanner. Everything matched up, actual pressure followed the scan tool info. Took valve body down, pressure tested ... |
10 |
