× Auto Repair Pros Member Benefits TechHelp Knowledge Base Forums Resources My iATN Marketplace Chat Pricing About Us Join Industry Sponsors Video Members Only Repair Shops Auto Pro Careers Auto Pro Reviews
Join Now
International Automotive Technicians Network
Prev Professional Automotive Repair Technical Discussions for February 1, 2012
International Automotive Technicians' Network (iATN) - Members Only
(Also Available: All, Asian, Chrysler, European, Ford, GM.)
Vehicle Owners: If you are seeking an automotive repair professional to service your vehicle, visit the iATN Repair Shop Finder.

Open Help Requests for Chrysler
Help Request Answers
1998 Chrysler Sebring JXi 2.5L MIL Lamp on VIN: 3C3EL55H9W
Hi, The codes in the related history were repaired by addressing those issues, the LT & ST trims were +25 before the o2 replacement and as sweet as could be after, the customer drove the car for about 100 miles afterwards and about that time the light came on ... Trouble codes: P0401 (Egr flow)
2005 Chrysler Pacifica Touring 3.5L MIL Lamp on VIN: 2C4GM68405
Hello everyone, I am hoping someone can help us with this problem child. It first came to our shop with the code P0133 and the tech here replaced both upstream and downstream O2 sensors with aftermarket sensors, cleared codes and performed a 40 mile test drive... Trouble codes: P0133 (O2 sensor 1/1 slow response)
2007 Chrysler Pacifica Touring 4.0L Emissions VIN: 2A8GF68X87
The customer went to have his vehicle emission tested last month and was told that it would not pass due to the O2 monitor and cat monitor have not set. We had scanned it and found no codes but the same issue with the monitors not running. We drove the vehicle...
2008 Chrysler Town & Country Touring 3.8L oil VIN: 2A8HR54P48
Seems were are seeing a bunch of Chrysler/Dodge 3.8's with excessive oil consumption. This van is drinking a quart of Pennzoil every 750 miles. Tailpipe emission is clean and spark plugs are clean also. We are going to try a different PCV valve and have alread...
1991 Dodge D350 5.9L Poor Idle Quality, Hesitation, Cuts out, Stall VIN: 1B6ME3655M
hi there. the concern with this vehicle is that it hesitates/bogs, backfires through the Throttle body under acceleration. runs rough at idle, sort of idle hunts at times. Scoped the TPS, hall effect CKP, and secondary ignition all seem OK. also scoped exhaust...
1996 Dodge Ram 2500 5.9L No Start VIN: 1B7KC23C5T
Engine will not start...customer towed truck to our shop. We work on his other vehicles so we are trying to fix this one even though we don't do much diesel engine work. It will start right up if you give it a shot of starting fluid and run ok but as soon as y...
2000 Dodge Ram 2500 5.9L Shift Point VIN: 3B7KC2669Y
I put in a transmission on this truck because the old one had a problem with it not shifting out of first at all. I dropped the pan and there was a lot of metal shavings in the pan and there was some small chunks of aluminum. The truck came back in two weeks ...
2004 Dodge Sprinter 2500 2.7L Lack of power VIN: WD2PD64414
I really hope somebody out there ran into this issue.please read carefully.truck came in with low power take from dead stop.looking at the drb3 when power brake the engine. Rpm max out to 1800 rpm and boost stays at 25psi wot.rpm should reach 2500 and boost sh...
2007 Dodge Ram 1500 TRX4 5.7L 4-5 shift VIN: 1D7HU18287
hi to all and thanks for any help. i this 2007 ram 1500 with a 5.7 and a 545rfe trans. when accelerating on to interstate when you level off at around 70 mph the tach will be at at around 2100rpm and will stay there for a while and then drop to around 1800, so...
2007 Dodge Ram 2500 SLT 6.7L MIL Lamp on VIN: 3D7KR28A37
Hi i cant clear codes and truck is in limp mode, is there any way to reset overhead message and return ecu to normal, the dpf burn off cant be activated from scanner due to reduced power Trouble codes: P242F, P0471, P2463, P1451
2008 Dodge Ram 2500 Laramie 6.7L Rear Main Seal VIN: 3D7K28A38G
Rear main seal look like its leaking. Is there any other thing that it could come from? It is dry above the flywheel housing. Thank for any hep!

Fixes & Summaries for Chrysler
Fix/Summary Answers
1996 Chrysler Cirrus LX 2.5L Cuts out, Stall VIN: 1C3EJ56H0T
As always thanks to all of you who take the time to respond to those of us seeking help. As I mentioned in the update I was waiting for a second PCM. The second PCM worked fine. Plugged it in and everything works. Thanks everyone again.
1998 Dodge Ram 1500 Laramie 3.9L Governor Pressure VIN: 1B7HC16XXW
First off, I want to thank everyone for their replies. We did hook a gauge to the Gov pressure port and it was showing exactly the same reading as the PCM. Coming out of park or neutral, the first series of shifts would occur normally, with gov pressure ra...
2006 Dodge Charger SXT 3.5L traction control VIN: 2B3KA43GX6
thanks for all the responses. turns out the bulb in the cluster was loose.
1998 Jeep Grand Cherokee Laredo 4.0L No Start VIN: 1J4GZ58S4W
recieved a lot of great information but I still haven't fixed the issue, mainly due to health reasons and time constraints. Soon as I figure it out I will post an update.. thanks to everyone that's helped!
Prev (Also Available: All, Asian, Chrysler, European, Ford, GM.) Next