 Prev |
Professional Automotive Repair Technical Discussions for August 8, 2011 International Automotive Technicians' Network (iATN) - Members Only |
Next  |
| (Also Available: All, Asian, Chrysler, European, Ford, GM.) | ||
| Vehicle Owners: If you are seeking an automotive repair professional to service your vehicle, visit the iATN Repair Shop Finder. | ||
Open Help Requests for Ford
| Help Request | Answers | |
| 1998 Ford Expedition Eddie Bauer 5.4L Noise VIN: 1FMPU18L8W All you ford guys I have a 98 expedition that has a noise and vibration in the front end at 40mph and on decel and its getting worse. We changed tires axles hubs and bearings, and even replaced the intermediate axle bearings between the axle and the differenti... |
View | |
| 1999 Ford F-250 Super Duty XLT 5.4L a/c VIN: 1FTNW21L1X This 99 Ford F250 has a history of poor a/c performance, but my friend has a 02 Ford F250 and his a/c cools just fine. Now seems like thing get worse at hwy speed, less cooling. I can feel all my suction lines very cool and I can see the system sweats like it ... |
View | |
| 2000 Ford Ranger XLT 3.0L Pats VIN: 1FTYR10VXY Hello, Hopefully someone has some insight into this problem with this vehicle. this is so intermittently we have been trying to find it for 2 years. almost never happenes in cold weather. The problem is the car will not start after hot soak the man is in pest ... |
View | |
| 2004 Ford Thunderbird 3.9L Carpet VIN: 1FAHP60A74 I have a 04 ford thunderbird, water drains out of the lower dash vent tubes with a/c on, cannot find the drain, water does drain at left floor pan/ frame area underneath car, but some is also leaking on the inside,anybody know where the drain is before i have ... |
View | |
| 2005 Ford E-450 Super Duty 6.0L No Start VIN: 1EDXE4SP25 Gentlemen we have an intermittent problem with this truck of no start, seems to happen most often after hot soak, eng cranks but will not start. Scanned data and ck icp pressure was at 570 psi, let cool all the way and usually will start.when diagnosing came u... Trouble codes: 602 (Pcm failure) |
View | |
| 2005 Ford F-350 Super Duty Lariat 6.0L Stall VIN: 1FTWX31P95 Customer brought truck in today with a dieing concern.It will die if brake is hit hard in neutral. it will die every time when put in reverse or drive but not neutral. It will dies at idle if you turn the the steering wheel fast. If you slowly put petal down i... |
View | |
| 2006 Ford Five Hundred SE 3.0L Starter Relay VIN: 1FAFP23166 We have here a 2006 Ford 500 that landed on a rock pile and ripped the fuel and brake lines out from underneath it. I installed a new fuel and brake line assembly from Ford, and Now it intermittently won't start. After a short diagnosis i found that the PCM is... |
View | |
| 2011 Ford f150 3.7L no starting condition VIN: 1FTEW1CM2B Hi friends this car wont start, i check codes with vcm ids and i dont have codes, it only start making short the starter relay, i dont known what to do, i dont have a wiring schematic to test if somebody can help me with the starting schematic please email me ... |
View | |
| 2003 Lincoln Town Car 4.6L Mechanical VIN: 1LNHM85W23 Ok please help with this cars AC!! Car came in with no cooling complaint. The compressor clutch was about to come off and it was very low in refrigerant. I replaced the orfice accumulator and the compressor. Charged system and test drove. Car still is not cool... |
View |
Fixes & Summaries for Ford
| Fix/Summary | Answers | |
| 2000 Ford E-250 Econoline 5.4L intake gasket VIN: V2YHA33179 went with the dorman intake. three used intakes all warped. |
8 | |
| 2004 Ford F-150 FX4 5.4L blend door VIN: 1FTPW14584 Well trucks fixed! We ended pulling the dash and replacing the heater box. So far so good. No issues with a/c temp. Just glad to get this one out of shop. Thanks |
3 | |
| 2008 Ford F-250 Super Duty XL 6.8L Stall, intake whistle VIN: 1FTSW21YX8 Kudos to Richard from California-the cause was a broken up catalyst media plugging converter. The whistle was apparently being caused by exhaust gas forced by the pipe to manifold seal. Thank you to all who replied to this posting. We actually discussed possib... |
7 |
