Join Now
International Automotive Technicians Network
Prev Professional Automotive Repair Technical Discussions for April 19, 2011
International Automotive Technicians' Network (iATN) - Members Only
Next
(Also Available: All, Asian, Chrysler, European, Ford, GM.)
Vehicle Owners: If you are seeking an automotive repair professional to service your vehicle, visit the iATN Repair Shop Finder.

Open Help Requests for Asian
Help Request Answers
2003 Honda Pilot EX 3.5L MIL Lamp on VIN: 2HKYF18533
I don't have access to an HDS scanner. However, I have repeatedly cleared the codes and immediately performed Honda's procedure for CKP Pattern Learn, with no results. I want to check misfire data in Mode 6 for this truck. Does anyone have a copy of this data ... Trouble codes: P0301 (Cylinder 1 misfire), P1399 (Random misfire pending)
View
2007 Honda Odyssey LX 3.5L power sliding door VIN: 5FNRL38667
I have a passenger side power sliding door on this honda that i am having trouble diagnosing. Problem started with door fully closing and latching and then the back of the door would come out/not stay latched. I tried to reset by pulling the fuse as described ...
View
2008 Honda CR-V EX 2.4L Hazard Lights VIN: 5J6RE48558
is there any issues with the MICU in these cars? never got concern to happen, cust has had car since I disconected battery drained loads. concern has not happened again. when it does happen she states that hazards will not turn off.
View
1996 Hyundai Elantra GL 1.8L Misfire VIN: KMHJW24M8T
We pulled fuel filter and fuel was dirty appear to have rust I suspected filter was clogged and took it apart to find very little debris to my surprise.Not sure what is going on.Injectors were reman. any suggestion would be appreciated! Trouble codes: P0300, P0302, P0303
View
1998 Mazda MPV ES 3.0L No Start VIN: JM3LV5231W
Came in stalled on highway have spark. Fuel pressure at 47 psi. Have no injector pulse. Noticed that the timing belt is moving toward the block and is shearing the belt. But teeth are not missing yet. Any help is appriciated
View
2005 Nissan Maxima SE 3.5L heater VIN: 1N4BA41E45
complaint is no heat in traffic. replaced t-stat w/oem, flushed system, heat turns cold at idle, like clogged core-but actually seems to flow OK. is there some kind of flow valve I cant find? also tried to bleed with a funnel fill while lifting front off groun...
View
2005 Nissan Altima S 2.5L 1-2 Shift VIN: 1N4AL11D35
Has a hard 1-2 shift no codes stored. Did some research and was looking into the Line pressure solenoid it ohms out at 3.5 ohms along with the dropping resistor at 12.5 ohms that is on the LF strut tower. Wires from TCM to resistor and solenoid all check out g...
View
1992 Other Asian Celica ST 2.0L No Start VIN: ST18300487
I need an JDM ECM pinout to repair broken wire between distributor and ECM. I cannot match this harness with any diagrams I have. The ECM has 3 connectors, 11 pin, 13 pin and 25 pin connectors. This is a Japanese Domestic Motor Vehicle. 3S-GE engine, ST183 bod... Trouble codes: 14 (No coil firing signal to ECM)
View
2005 Scion tC 2.4L 1st gear VIN: JTKDE17715
I have a 2005 Scion tC here with a whine in 1st gear. It whines at all times in 1st, both under load and coasting, clutch in or out. If I pull it out of first while coasting, the whining immediately stops. If I try to engage first while moving at over 20MPH, I...
View
2005 Scion tC 2.4L 1st gear VIN: JTKDE17715
I have a 2005 Scion tC here with a whine in 1st gear. It whines at all times in 1st, both under load and coasting, clutch in or out. If I pull it out of first while coasting, the whining immediately stops. If I try to engage first while moving at over 20MPH, I...
View
2005 Subaru Outback XT Limited 2.5L Cuts out VIN: 454BP67C05
Car came in with bad turbo, no start and code POO21. Checked belt timing two teeth off on drivers intake cam replaced belt and tensior. Replaced turbo, turbo oil pipes and two screens, pulled oil pan and cleaned, no metal in pan. Now it idles and runs fine a... Trouble codes: P0021 (a cam over advanced)
View

Fixes & Summaries for Asian
Fix/Summary Answers
1998 Honda Civic LX 1.6L No Start, Cuts out VIN: JHMEJ6553W
Problem turned out to be a faulty brand new factory ect sensor, it would intermitently read a high temperature, got lucky and caught it on the scanner when it was doing it. Thanks everyone for the help.
8
2002 Honda Accord EX 2.3L Poor Idle Quality, Misfire, MIL Lamp on VIN: JHMCG65822
First thank you to all who replied. Many good ideas as to the problem. it took two weeks for my dad to get the car back to me. the problem that the skip is gone and i dont know why. My dad has put over 1000 miles on and there is no skip to be had. If it does r... Trouble codes: P0300, P0303.
22
2006 Mazda MX-5 Miata 2.0L intake VIN: JM1NC25FX6
intake fixed car...customer is member of a Miata club and got his hands on a used one...still not sure of actual source of noise ( what is actually "broken" in IMRC system) but customer was happy anyway...testing of solenoid and actuator yielded no clues since...
2
1997 Mitsubishi Eclipse 2.0L electric VIN: 4A3AK34Y8V
thanks for your help we replace crank sensor for dealer part after this problem is fixed.
5
2004 Mitsubishi Diamante LS 3.5L Accessories VIN: 6MMAP67P14
With some help from the two responses this was to easy! I simply disabled the hood switch to prevent the system from arming. Thanks for your help.
2
1999 Subaru Forester S 2.5L Stall VIN: JF15F6553X
Thanks to all who replied. Its nice to now that I'm not in this alone. I found the maf sensor to be killing the 5v ref signal. this signal is shared by the tps,iac, as well. I unplugged all the above and she ran. Plugging them in one at a time I found that whe...
10
1994 Suzuki Sidekick JLX 1.6L Cuts out VIN: JS3TD03V1R
I have sent the computer out to be rebuilt. I am confident this will resolve the problem. The injector driver is breaking down causing the surging. Will try to add to this after the rebuilt computer is installed and vehicle is working correctly.
5
2003 Toyota Highlander 3.0L Abs VIN: JTFHF21AX3
this car is fixed,first of all thank you guys for great help.as this car been to other shops,i had no idea what they did.but problem was 5v ref wire for decelration senser was short to sheld wire,when you turn the key on ecu will ground this sheld wire,that is...
10
Prev (Also Available: All, Asian, Chrysler, European, Ford, GM.) Next