Join Now
International Automotive Technicians Network
Prev Professional Automotive Repair Technical Discussions for December 27, 2010
International Automotive Technicians' Network (iATN) - Members Only
Next
(Also Available: All, Asian, Chrysler, European, Ford, GM.)
Vehicle Owners: If you are seeking an automotive repair professional to service your vehicle, visit the iATN Repair Shop Finder.

Open Help Requests for Chrysler
Help Request Answers
1995 Chrysler Cirrus LX 2.5L No Start VIN: 1C3EJ56H2S
I had the car PCM changed because of run on three cylinders after changing the PCM car ran great for (2) days when to start on the third day lights,and horns started flashing and blowing,that put the car in thief -mode car has NO-REMOTE,never had one.return th...
View
2001 Chrysler Voyager 3.3L cluster VIN: 1C4GJ25381
Wierd one here, just trying to figure out why it's doing what it's doing. Had a speedo problem, another tech put in a cluster immedatly was flashing/pulsing guages, got a second worked fine until customer got nearly home. I test drove this morning verified con...
View
2005 Chrysler 300 (Car) C 5.7L exhaust valve VIN: 2C3JA63H55
This chrysler came in with a dead miss on cylinder #2 check compression and had 0 psi. I pulled the vavle cover and rocker arm assembly and the number 2 exhaust valve is about half inch down in the head compared to the other cylinders. I tried prying up on the...
View
2005 Chrysler 300 (Car) 2.7L Stall, MIL Lamp on, no power VIN: 2C3JA53G65
this vehicle came in, intermittent stall problem on decel, and intermittent loss of throttle response, will idle but will not accelerate. ignition can be cycled, will start and run (electronic throttle lamp will be flashing). clear codes, can drive 30 feet or ... Trouble codes: P2110, P2112
View
1998 Dodge Ram 2500 Truck 5.9L 1st Reverse VIN: 1B7KF23DXW
I do not know where to go at this point . The normal items have been done we have also bleed the clutch hydraulic system with no change.
View
2007 Dodge Ram 3500 Truck SLT 6.7L No Start VIN: 3D6WG48A77
A Friend has replaced the head gasket. The vehicle would run when it came in an now we are unable to get fuel pressure to come up. all fuses check and recheck good. The cam sensor shows all wires to computer to be good. The sensor also shows a good square wave... Trouble codes: P0341
View
2006 Jeep Grand Cherokee Limited 5.7L Misfire, MIL Lamp on VIN: 1J8HR58226
I have an 06 jeep grand cherokee with the 5.7l hemi. The vehicle has a misfire when first fired up in the morning when its cold. Around 15 degrees outside at night lately. It will run fine for a few mins and then cylinder #1 will misfire for 30 to 45 seconds a... Trouble codes: P0301
View
2007 Jeep Commander (Truck) Limited 4.7L Air bag VIN: 1J8HG58P77
Hi guys. I have an 07 jeep commander that has an air bag light on. It came in with code b1b28-front row driver seat belt pretensioner circuit low and code b1bff which i could not find a code description. Just got the vehicle from the auction so i cleared the c...
View

Fixes & Summaries for Chrysler
Fix/Summary Answers
2005 Chrysler 300 (Car) 2.7L No Start, Stall VIN: 2C3AA63H05
REPLACED THE CANNISTER AND THE PURGE VALVE AGAIN- FOUND RAW FUEL IN THE EVAP LINES. CLEANED AND RE-ASSEMBLED WITH THE NEW PARTS. FILLED TANK AND DROVE- PROBLEM HAS YET TO COME BACK..
11
2001 Dodge Durango 4.7L 2-3,3-4 shift VIN: 1B4HS28N11
Thank you for all the help I recieved for my request. I have not been able to have the vehicle back yet, but here is a summary of what I learned. Change fluid and filter, use only ATF +4, synthetic fluid might not look burned but might lose viscosity. also ...
10
2007 Dodge Dakota SLT 3.7L low compression VIN: 1D7HE22K27
thanks for the response on this one. after pulling valve covers i found right cam shaft broken between cylinder #2 and #4. i am waiting on customer to decide on replacement of heads or complete engine.
5
Prev (Also Available: All, Asian, Chrysler, European, Ford, GM.) Next