|Prev||Professional Automotive Repair Technical Discussions for December 7, 2010
International Automotive Technicians' Network (iATN) - Members Only
|(Also Available: All, Asian, Chrysler, European, Ford, GM.)|
|Vehicle Owners: If you are seeking an automotive repair professional to service your vehicle, visit the iATN Repair Shop Finder.|
Open Help Requests for Chrysler
|2001 Chrysler 300M 3.5L compressor VIN: 2C3HE66G61
This car is a regular customers. This is something I haven't personally ever seen before. It came in with a complaint of a humming noise with the ac or defrost on at idle. We had replaced the compressor for this same problem two years ago. It sounds exactly li...
|1996 Dodge B1500 3.9L Cuts out VIN: 2B7HB21X6T
Help please customer brought this van in for normal tune up not saying anything about a problem just purchased van said it was just due. Came back couple months later cutting out when first accel. We found alot of play in timing chain and replaced it. Now it c...
|2000 Dodge Dakota 3.9L Slave Cylender VIN: 1B7GL2AN1Y
installed slave cylender and now have no pedal, there is no bleeder valve to bleed system.
|2001 Dodge Durango SLT 4.7L timing? VIN: 1B4HS28N91
Hello to all and thank you in advance for yopur time.. My problem is replaced timing chains, guides and tensoiners because of noise and loose left chain. Everything went well, or so I thought (guess thats what I get for thinking)! Completed repairs (per alldat...
|2001 Dodge Durango 5.9L front brakes
Hello guys I have a durango here that the customer is complaining that the front brakes lock up during normal braking on wet roads. I have not been able to confirm this on wet roads as it is not raining here when I have seen the car. What I have noticed is on ...
|2002 Dodge Intrepid ES 3.5L No Start VIN: 1000VINR02
this one is for the chrysler techs.i installed a 02 2.7l engine and trans that came out of a deer hit car.valvecovers were damaged.i used the same harness and cam/crank sensors.when atempting to start the cam/crank go out of sync.after pulling my hair out for ...
Fixes & Summaries for Chrysler
|1997 Dodge Dakota Sport 5.2L Poor Idle Quality, Stall VIN: 1B7GG23Y5V
Thanks to all that replied. I had a 1.2 voltage drop on the ground side and that made small difference in the 5 volt return signals but the issue was the PCM took a dump intermittantly. I put a known good unit in from a runnig vehicle and bingo it ran perfect....
|2003 Dodge Durango R/T 4.7L Hesitation, Stall VIN: 1D4HS58N53
Thanks for the replies! We were unable to duplicate the complaint this time around but rechecked our work, scoped the TPS, checked the connector at the map sensor for corrosion, and cleaned all grounds. The connector was clean and tps looked fine. We found a... Trouble codes: P0121.
|2008 Dodge Sprinter 3500 3.0L Cuts out VIN: WDWPE84538
Guys A fix. Firstly a big thanks to the guys that offered help. In the ultimo it wasn't the job that took so long but the chain of command who insisted they source the parts involved! To correct the cutting out we replaced the engine harness as recommende... Trouble codes: P2978 (EGR Cooler position sensor open circuit), P2051 (Fuel rail pressure sensor max pressue exceeded), P2017 (Fuel rail pressure monitoring too low), P2953 (Intake swirl port actuator open/sensor value too low).
|1993 Jeep Grand Cherokee 5.2L No Start VIN: 1J8HR48N45
Thanks to all who provided information for this vehicle. I went through and checked the power and ground circuits as well as the bus circuits, 5 and 8 volt circuits, with no problems found except for the high voltage on the 8 volt reference circuit. Ordered ...
|1996 Jeep Grand Cherokee Limited 4.0L No Start, Cuts out VIN: IJ4GZB8SXT
I found anothe jeep cherooke of same month and year which had addiatcl remote for activation /deactivation - customer was gong back to dealer who said had already programmed vehicle to find out why he didnt get the remote - havent heard back - Problem was diff...