 Prev |
Professional Automotive Repair Technical Discussions for October 15, 2010 International Automotive Technicians' Network (iATN) - Members Only |
Next  |
| (Also Available: All, Asian, Chrysler, European, Ford, GM.) | ||
| Vehicle Owners: If you are seeking an automotive repair professional to service your vehicle, visit the iATN Repair Shop Finder. | ||
Open Help Requests for Chrysler
| Help Request | Answers | |
| 1994 Chrysler Concorde 3.3L blower/controlhead VIN: 2C3EL56T7R 94 Concorde Auto A/C. Came in with blower motor running (probably 3/4 speed)anytime ignition was on. Could control modes but not fan speed. Customer had removed blower fuse. Have power and ground at blower module. Remove signal wire from module and fan goes to... |
View | |
| 2004 Chrysler PT Cruiser 2.4L engine I got this car brought in by a wrecker and it had been run hot. the lady had taking it to another shop where they put a water pump and timing belt on it and it still ran terible. When I tore the motor down it had a melted piston and a lot of warped valves. I h... |
View | |
| 2007 Chrysler PT Cruiser 2.4L unknown VIN: 3A4FY58B47 my question is . is there any way to view evap. core with out having to remove dash ? i can not find anything else leaking. |
View | |
| 1997 Dodge Dakota SLT 5.2L Surge VIN: 1B7GL23Y0V this truck cam to my shop, it surges at times, it was at another shop and had a after makret tp sensor installed. advised to take it to the dealer. it came here, checked code. i have 5 volts vref, ground, checked single returen, i have .8 volts. but on the sca... Trouble codes: 24 (tp out of range) |
View | |
| 2004 Dodge Ram 1500 SLT 4.7L driven disk VIN: 1D7HU18N44 looking for some input from some seasoned veterans here. replacing clutch in this ram 1500. ordered clutch kit from napa and notice inner dampner springs in driven disk approximatley an inch too short, they're just bouncing around inside the outer dampner spri... |
View | |
| 2006 Dodge Sprinter 2500 2.7L stuck in 1st VIN: WD2PD64445 Suspect trans failure stuck in 1st, has code 2225,speed sensor voltage fault, had this code before the new tcm as well.need more testing info before I condemm trans.Do these trans fail often? |
View | |
| 2007 Jeep Commander 3.7L Unknown VIN: 1J8HG48K18 Please help!!!, truck came in with code 2767- input speed shaft sensor 2 no signal, customer stated she had been driving it over a month in and out of limp mode, turned off to reset it and kept driving. I replaced the hydro-electric module over the valve body ... |
View |
Fixes & Summaries for Chrysler
| Fix/Summary | Answers | |
| 2004 Chrysler 300M 3.5L engine VIN: 2C3HE66G34 It worked I used shop air to blow through hole from themostat to upper radiator hose. worked great customer is happy. THANKS FOR ALL THE HELP |
8 | |
| 2000 Dodge Ram 2500 5.9L wheel speed sensors VIN: 1B7KF2361Y sorry about the delay in closing.thanks for the responces.as some of you suggested that the front bearing could be causing he issue.which is probably the case for the wheel speed sensor on the front to be dropping out,however i decided that the only correction... |
7 | |
| 2004 Dodge Stratus SXT 2.4L MIL Lamp on VIN: 1B3EL46X94 Well, gentlemen, this vehicle is done. Sorry it took so long to close it because of circumstances beyond my control. I was able to find a good used pcm for it but in order to satisfy the security system on board it needed to be flashed. Since I didn't have ... Trouble codes: P0141 (oxygen sensor 1/2 heater performance /rationality). |
4 | |
| 1995 Jeep Grand Cherokee Orvis 4.0L Poor Idle Quality, Cuts out, Stall, Misfire VIN: 1J4GZ7857S Okay this thing is a bear! I have checked cam/ crank sync while it ran bad and when it ran good and they look good, I removed the distributor and found what I thought was excessive play so I tried dropping in another and no difference. I checked timing chain... |
9 | |
| 1999 Plymouth Grand Voyager SE 3.3L Instument Panel VIN: 1P4GP44R7X soory about the delay but the customer has not come back in for any repair, they did tell me that the cluster started to work again so i told them it will need the wiring joints resoldered and just waiting on when they want it done thanks |
11 |
