 Prev |
Professional Automotive Repair Technical Discussions for July 1, 2010 International Automotive Technicians' Network (iATN) - Members Only |
Next  |
| (Also Available: All, Asian, Chrysler, European, Ford, GM.) | ||
| Vehicle Owners: If you are seeking an automotive repair professional to service your vehicle, visit the iATN Repair Shop Finder. | ||
Open Help Requests for Chrysler
| Help Request | Answers | |
| 1999 Chrysler 300M 3.5L Poor Idle Quality, MIL Lamp on VIN: 2C3HE66G6X Hey guys, got a question about this 99 Chrysler 300M. It came into the shop last week overheating and with a check engine light on. We replaced the fan assembly to fix the o/heat condition, and checked the codes. At the time it had a p0300-random cyl. misfire.... Trouble codes: P0300, P0302, P0304, P0306 |
View | |
| 2000 Dodge Durango 5.2L Hvac Vents VIN: 1B4HS28Z4Y Hello all, I have a 2000 Durango -- the hvac system is only coming thru the defrost vents( default mode i guess ) I have checked under the hood for vacuum leaks - removed the battery -- no leaks detected -- any help would be appreciated |
View | |
| 2004 Dodge Intrepid ES 3.5L Stall, MIL Lamp on VIN: 2B3HD56M04 While watching cam sensor 5 volt ref and return signal while car acted up. Loss only signal return not ref voltage.checked wire even replaced wire from pcm to cam sensor still got same problem.it is very intermittent but does cause stalling.does seem to be mor... Trouble codes: 340 (Loss cam signal), 344 (Cam signal intermittent) |
View | |
| 2008 Dodge Caliber SXT 2.0L Drive Belt VIN: 1B3HB48B48 We have a 2008 dodge caliber 2.0 / belt vibrates / slaps at idle making severe noise . Client had new tensioner and belt installed. We have spun all pulleys and do not feel any bearing or play issue. The alternator has slight play up and down movement. We load... |
View | |
| 1988 Jeep Cherokee Limited 4.0L Excessive Emissions VIN: 1JCMT7892J I inherited this vehicle from another tech who went on his week vacation today. He tested everything but feels that he missed something(and told me good luck). This jeep runs great but fails for NOX only, during a California SMOG test. HC & CO are OK. Fuel pre... |
View | |
| 1996 Jeep Grand Cherokee Limited 5.2L Compressor VIN: 1J4GZ78Y1T Compressor is not engaging. Can operate compressor with scan tool. Found codes 01 in-vehicle temperature sensor and 26 in ATC. Mitchell shows code 26 as reseved. Mitchell does not tell you how to test this system very well. I think it has a bad ATC control. |
View | |
| 1999 Jeep Grand Cherokee Laredo 4.7L No Start, Stall VIN: 1J4GW68N6X this jeep was towed in as a no start i hopped in it and it fired right up put the scanner on and checked data on ckp and cmp sensors all ok i shut the hood and and car stalled and lost communication to computer.late in the day so i pushed it outside next day s... |
View | |
| 2000 Jeep Wrangler Sahara 4.0L 1-2 shift VIN: 1J4FA59S5Y Hello. We have a Wrangler here with a 5-speed manual transmission. When you shift from 1st to 2nd you get a clanking noise from the bell housing area. It sounds like excessive gear lash. We pulled the trans to check the clutch and it looks ok. On the trans the... |
View | |
| 2003 Jeep Liberty Sport 3.7L Stall, MIL Lamp on VIN: 1J4GK48K13 thanks in advance for the help.this jeep liberty came in with complaint of stalling and no start for 20-30 min checked codes found PO320 no crank referance signal at pcm. checked connection and wires for damage then replaced crank sensor , still same prob. rep... Trouble codes: P0320, P1391 |
View | |
| 2005 Jeep Grand Cherokee Limited 4.7L Dead Battery VIN: 1J4HR58N35 Vehicle may not start after sitting for 3 to 5 days intermittently. This does not happen consistantly. Last time it happen battery had 2-3 volts. Charged battery, tested charging system (ok) and check for drains on battery. After 20-30 minutes i end up with ma... |
View |
Fixes & Summaries for Chrysler
| Fix/Summary | Answers | |
| 2007 Chrysler Pacifica 4.0L Steering Angle Sensor VIN: 2A8GM78X77 This hot rod is finally fixed. I have had the new clockspring sitting on my toolbox for 2 weeks now but no car to put it in. Installed clock spring and recalibrated, good as new. The old one sounded like a rattle when I shook it. Guess i found the problem. Tha... |
5 |
