 Prev |
Professional Automotive Repair Technical Discussions for June 17, 2010 International Automotive Technicians' Network (iATN) - Members Only |
Next  |
| (Also Available: All, Asian, Chrysler, European, Ford, GM.) | ||
| Vehicle Owners: If you are seeking an automotive repair professional to service your vehicle, visit the iATN Repair Shop Finder. | ||
Open Help Requests for Chrysler
| Help Request | Answers | |
| 1993 Chrysler LeBaron 2.5L Fuel Pump VIN: 1C3XU6536M Fuel pump was replaced at another shop. I have no information for this vehicle, all my books are 800 miles away. Can someone send me the wiring diagram for this, it appears that the computer should be controlling the fuel pump and is not. I am in bad need of t... |
View | |
| 2000 Chrysler LHS 3.5L Starter/ Antitheft VIN: 2C3HC56G9Y There is one code for a serial link internal failure. I clear the coed and it comes back instantly. I diconnected the battery for a couple hours and it did nothing to help. I also tried to leave the ignition on for a couple hours and no change. We toed it to t... |
View | |
| 2000 Chrysler Town & Country LXi 3.8L Timing Chain VIN: 1C4GP54L9Y We did the timing chain on this vehicle and used the mitchell guide to set timing this was completely wrong no compression. Need to know how to time this vehicle. Thank you |
View | |
| 2002 Chrysler PT Cruiser 2.4L MIL Lamp on VIN: 3C8FY68B32 Car came in with P0320 The lady driver said before the check engine light came on she heard a thump noise under the passenger side, pulled over shut the engine off, checked around and underneath the car to see if she ran over something.Found nothing. Then when... Trouble codes: P0320 (No crank Reference signal at PCM) |
View | |
| 2006 Chrysler 300 C 5.7L input speed sensor VIN: 2C3KA53G16 Cars runs fine most of the time but will go to limp mode sets code p2767 input - turbine sensor b circuit no signal. Can stop, turn off ignition, restart and all will be fine for awhile. Also sets generic code P0700 trans control system malfunction. This is my... |
View | |
| 2002 Dodge Ram 1500 SLT 5.9L RS Hi-Beam, LS Low-Beam, Front Turn Signals, LR Tu VIN: 1D7HU18ZX2 I have no R.S. high beam, L.S. low beam, front turn signals, or L.R. turn signal. No power to these lights coming out of the front control module. If I power the circuit up with 12v jumper, the lights work. I also cannot make them work with the Snap-On scanner... |
View | |
| 2007 Dodge Ram 2500 SLT 5.9L transfer case VIN: 1D7KS28C87 I've got this truck that the 4 wheel drive comes on and off at times, also I had the encoder motor on the transfer case switching when opening the door. I was told the A/C transducer would cause this. Replaced it to no avail. When scanning I found history code... |
View | |
| 2008 Dodge Magnum SXT 3.5L Steering VIN: 2D4GZ37V68 Hello there, We have a 2008 magnum in the shop that had a definite front rotor pulsation on application. Measured run out and we had .007. Installed a new set of rotors and clocked till we had under .002 runout. Drove vehicle and the pulsation in the steering ... |
View | |
| 1999 Jeep Grand Cherokee Laredo 4.0L No Start VIN: 1J4GW58S5W Complaint of a no start after short or long drives. Origanal had no comunication with the PCM removed and inspected no corrosion good terminal contact. Removed relays from panel found some corosion and cleaned. Customer road tested several days problem reoccur... |
View | |
| 2001 Jeep Cherokee Sport 4.0L air bag light, inop cluster VIN: IJFF48SX1L we retrieved p1698 and p1694 tested bus wires and found to check out ok i can communicat with ecm but tcm will not respond. we replaced tcm with a known good module and still have same problem and codes. someone please help! |
View | |
| 2005 Jeep Wrangler Unlimited 4.0L Cuts out VIN: 1J4FA44S65 Hello to all that read and help. This Jeep came in with p0016 and p0344 will run good at idle and will rev with on problem. On test drive @ 2000 to 3000 rpm engine will start to cut out until you let off the throttle.I have ran the wire harness and checked the... Trouble codes: P0344, P0016 |
View | |
| 2005 Jeep Grand Cherokee Limited 5.7L heat control VIN: 1J8HC58235 HVAC has no codes No matter AC compressor is on or off there is too much heat in all vents. For instance: if both right and left temperatures are set to 70, even after a lot of time, system is blowing very hot air (100F or more). Including on rear vent. For... |
View |
Fixes & Summaries for Chrysler
| Fix/Summary | Answers | |
| 1997 Chrysler Cirrus LX 2.5L P0500, vss VIN: 1C3EJ56H5V Fixed, ended up finding where someone had ran a wire from tps 5 volt reference to the steering system wire signal, which is part of circuit for output speed sensor signal wire and was staying at 5 volts all the time. |
5 | |
| 1999 Dodge Durango 5.9L No Start, Poor Idle Quality VIN: 1B4HR28ZXX thanks for all responses. tried heat gun to pcm with engine cold still have no bus no com to scan tool. would try pcm but dont have drb3 to program miles or vin. boss decided to cut losses from job as too not be married to a problem child. customer is to tak... |
6 | |
| 2001 Dodge Durango 4.7L Misfire, MIL Lamp on VIN: 1B4HS28N31 had to replace ECM. thanks to everybody who replied |
4 | |
| 2002 Dodge Ram 1500 SLT 4.7L ABS Module VIN: 3D3HA18N82 Approximately 1 foot from the ABS module we found a broken wire in harness that was sometimes making contact and sometimes not. |
2 | |
| 2006 Dodge Ram 3500 SLT 5.9L Poor Idle Quality, Surge VIN: 3D7MX48C26 Thanks for the replies. I think Tom from North Carolina hit it on the head. When put into gear, the engine would have to work harder to hold the same idle. Fuel injector pressure would climb, and the truck would actually "lurch" forward when you let off the... |
5 | |
| 1986 Jeep CJ7 4.2L Oil Pressure VIN: 1JCCM87EGH Thanks for all that helped. The wires in question from the other oil pressure switch control the electric choke. |
5 | |
| 1997 Plymouth Breeze 2.0L No Start VIN: 1P3EJ46C4T Yes I did get this finally repaired, I did replace crank sensor with a factory sensor. Still no crank signal, it cam with a new connector also. (the crank sensor I got from the local parts store came with one also, I had already installed that connector) I dec... |
5 |
